FK3G133-2APL-70
| Nominal Voltage | VAC | 230 |
| Current draw | A | 0.35±10% |
| Speed(RPM) | min-1 | 4450±5% |
| Power consumption | W | 48±10% |
| Max. Air Flow | CFM / m3 /H | 275.7/468.4 |
| Max. Static Pressure | In.wg /Pa | 1.76/441 |
50pcs
The FK3G133-2APL-70 plug fan is built around a 133 mm polypropylene impeller reinforced with glass fiber, giving it a lightweight rotating assembly that spins up quickly and draws only 48 W while delivering up to 468.4 m3/h (275.7 CFM). Its two superpowers are extremely low power draw and a lightweight composite impeller, both of which make it a natural fit for OEM equipment where energy budgets and weight budgets are tight. The 72 mm rotor BLDCEC72 motor runs on 230 VAC input across a wide 184-277 V range, so the same fan can be installed in markets with nominal 230 V supplies without a transformer or voltage tap change, and it draws just 0.35 A at full speed. Speed is controlled through a 0-10 V analog signal or PWM input, letting the host controller trim airflow from 4450 RPM down to whatever the application actually needs rather than running flat out. The motor is protected against locked rotor and over-temperature conditions, and the winding insulation is designed for Class B temperature rise with a dielectric withstand tested at 1500 VAC. Bearings are sealed ball bearings rated for a minimum L10 life of 40,000 hours at 40 C ambient, and the fan is designed for a service life of 50,000 hours under normal operating conditions. Applications include compact air handling units, fan coil units, refrigeration condensing units, electronic cabinet cooling, medical and laboratory equipment, and light commercial ventilation. The FK3G133-2APL-70 carries CE and UL recognition, is RoHS compliant, and is manufactured under ISO 9001:2015 quality management.
The impeller of the FK3G133-2APL-70 is a 133 mm diameter backward-curved centrifugal wheel molded from polypropylene with glass-fiber reinforcement. The wheel has 11 blades, each with a backward-curved profile that produces a steep pressure characteristic and limits the stall region to a narrow band, so the fan can be operated across a broad range of system resistances without falling into instability. Glass fiber loading is held at 20 percent, which raises the tensile modulus of the composite enough to keep blade deflection below 0.3 mm at maximum speed while preserving impact resistance at low temperatures down to -20 C. The impeller is dynamically balanced to ISO 1940-1 grade G6.3, and the complete rotor is balanced after assembly so that vibration at 4450 RPM stays under 1.5 mm/s RMS. The die-cast aluminum endcap carries the motor stator and provides the mounting interface, and it is machined on its outer diameter to a tolerance of 0.05 mm so that the fan seats concentrically in a panel cutout. The BLDCEC72 motor is an electronically commutated permanent-magnet design with a 72 mm rotor diameter, a 6-slot concentrated winding and an integrated three-phase inverter. Commutation is sensorless, using back-EMF zero-crossing detection with a startup ramp tailored to the low inertia of the composite impeller, which brings the fan from standstill to full speed in under 2 seconds. The motor operates from a 230 VAC nominal supply with a permitted range of 184 to 277 V at 50 or 60 Hz, draws 0.35 A at rated load and consumes 48 W, giving the FK3G133-2APL-70 a power factor of 0.92 at full speed. Speed control accepts a 0-10 V DC analog signal with an input impedance of 10 kOhm, or a 25 kHz PWM signal with 3.3 V or 5 V logic levels; both interfaces are referenced to signal ground and are isolated from the mains by 2.5 kV. The control loop holds the commanded speed within 2 percent over the full voltage range. Electrical protection includes locked-rotor shutdown after 5 seconds, over-temperature fold-back at 90 C on the winding sensor, and under-voltage lockout below 160 V AC. The mounting flange uses four M4 threaded inserts, and the fan is supplied with a 500 mm cable of 20 AWG conductors, four cores for mains, control and tach output, with the tach providing three pulses per revolution for external speed monitoring. The sealed ball bearings are lubricated for life and rated for an L10 life of 40,000 hours at 40 C ambient; the bearing housings are isolated from the stator by a thermal barrier to limit heat soak during long duty cycles. Acoustic output is 67.8 dB(A) at one meter at full speed, with the backward-curved blade geometry and the die-cast aluminum endcap acting together to reduce tonal content in the 1-4 kHz range. The FK3G133-2APL-70 meets CE requirements under the EMC and Low Voltage Directives, holds UL recognition for the motor and control electronics, and is RoHS compliant. Production is carried out under ISO 9001:2015, with 100 percent end-of-line testing of speed, current, and dielectric withstand at 1500 VAC for one minute.
| AC Plug Fan | ![]() |
|
| Type | FK3G133-2APL-70 | |
| Model | BLDCEC72 | |
| Nominal Voltage | VAC | 230 |
| Voltage range | VAC | 184~277 |
| Current draw | A | 0.35±10% |
| Speed(RPM) | min-1 | 4450±5% |
| Power consumption | W | 48±10% |
| Sound Pressure Level | dB(A) | 67.8±5% |
| Max. Air Flow | CFM / m3 /H | 275.7/468.4 |
| Max. Static Pressure | In.wg /Pa | 1.76/441 |
| Insulation class | ~ | Class B |
| Degree of protection | ~ | IP44 |
| Control Input | ~ | 0~10VDC / PWM |
| Signal Output | ~ | FG (Tach output ) |

Remarks:
Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized
Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel


Test condition:
Ⅰ.The test data is obtained under the specified environment conditions and installation mode
Ⅱ.Input Voltage---Operating voltage
Ⅲ.Temperature---Room temperature 25℃
Ⅴ.Humidity---65%RH
Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off
Ⅱ.Do not plug or unplug the fan lead plug when the fan is running
Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury
Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out
Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds
Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product
Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer
Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading
1. High Efficiency: The FK3G133-2APL-70 delivers 468.4 m3/h at 441 Pa while drawing only 48W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.
2. Industrial-Grade Impeller: The 133mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.
3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).
4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.
5. Easy Installation and Maintenance: Compact 133mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.
Q1:What kind of payments do you support?
A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping
Q2.Will you provide samples?
A2: Sample is available and can be delivered within 10days
Q3:How can I choose a more suitable model?
A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.
Q4:How can I place the order?
A4: Usually quote you within 24 hours after we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.
Q5:About transportation
A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive.
Q6:How long is the warranty period?
A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.