FD3G146-48GL-90
| Nominal Voltage | VDC | 48 |
| Current draw | A | 4.2±10% |
| Speed(RPM) | min-1 | 1700±5% |
| Power consumption | W | 201.6±10% |
| Max. Air Flow | CFM / m3 /H | 890.9/1513.9 |
| Max. Static Pressure | In.wg /Pa | 1.31/328 |
50pcs
When a single compact blower must move more than 1500 m3/h of air, the FD3G146-48GL-90 dual inlet centrifugal blower is engineered to replace two smaller fans in one space-saving footprint. Its 146 mm galvanized steel impeller and precision-balanced dual-inlet housing deliver a maximum airflow of 1513.9 m3/h (890.9 CFM) at 1700 RPM, while the 92 mm rotor BLDCDC92 brushless DC motor generates 201.6 W from a 48VDC nominal supply (operating range 36 to 57VDC). This model is purpose-built for telecom and data-center environments where the -48VDC bus is the standard, and its 4.2 A current draw keeps distribution losses low across the cabinet. Air pressure reaches 1.31 in.wg (328 Pa), enough to push through dense filter media or long duct runs without stalling. Speed is controlled via a 0-10V analog interface or PWM input, allowing seamless integration with DCIM monitoring and variable-load cooling strategies. The motor carries Class F insulation and is protected against dust and moisture for reliable continuous duty. Bearings are rated for 70,000 hours at 40 degrees C, minimizing service intervals in hard-to-reach installations. Typical applications include telecom shelters, outdoor cabinets, EV charging stations, industrial enclosures and renewable-energy power conversion systems. The unit is CE and RoHS compliant and backed by FANOVA's OEM/ODM engineering support.
The FD3G146-48GL-90 is a dual inlet centrifugal blower built around a 146 mm diameter impeller formed from galvanized steel sheet. Each impeller uses a high blade count with a forward-curved profile that maximizes pressure development at moderate tip speeds, and the dual-inlet configuration draws air from both sides of the scroll housing to double intake area without increasing the package width. The impeller is dynamically balanced to ISO 1940 G6.3, reducing vibration and bearing load during continuous operation. The endcap and housing are die-cast aluminum, chosen for its dimensional stability, heat dissipation and resistance to corrosion in humid or polluted air streams. The rotor diameter is 92 mm, paired with a BLDCDC92 brushless DC motor that uses electronic commutation to eliminate brush wear and sparking. Motor windings are rated for 48VDC nominal with an allowable input range of 36 to 57VDC, and the drive electronics maintain stable speed control across that band. At 1700 RPM the blower produces a maximum airflow of 1513.9 m3/h (890.9 CFM) and a maximum static pressure of 328 Pa (1.31 in.wg) while consuming 201.6 W at 4.2 A. Speed can be commanded through a 0-10V analog signal or a PWM input, and a tachometer output provides real-time RPM feedback for DCIM and building-management systems. The motor is insulated to Class F and protected by an integrated lock-rotor and over-temperature circuit that shuts down the drive if airflow is blocked. Bearings are pre-lubricated ball bearings rated for 70,000 hours at 40 degrees C ambient, and the motor shaft runs in a precision-machined bearing seat to limit axial play. Electrical connection is made through a 20AWG cable, 209 mm in length, with flying leads for direct termination to a terminal block or controller. The blower is designed for panel-mount installation with four M4 threaded inserts in the aluminum endcap, and the discharge orientation can be rotated in 90-degree increments during assembly to suit duct routing. Acoustic output is 72 dB(A) at maximum speed, and the balanced impeller and rubber isolation grommets supplied with the unit reduce structure-borne noise. The FD3G146-48GL-90 is CE marked, RoHS compliant and manufactured under FANOVA's ISO 9001 quality system, with 100 percent run-in testing and a routine performance check on every unit before shipment.
| DC Dual Inlet Centrifugal Blower | ![]() |
|
| Type | FD3G146-48GL-90 | |
| Model | BLDCDC92 | |
| Nominal Voltage | VDC | 48 |
| Voltage range | VDC | 36~57 |
| Current draw | A | 4.2±10% |
| Speed(RPM) | min-1 | 1700±5% |
| Power consumption | W | 201.6±10% |
| Sound Pressure Level | dB(A) | 72±5% |
| Max. Air Flow | CFM / m3 /H | 890.9/1513.9 |
| Max. Static Pressure | In.wg /Pa | 1.31/328 |
| Insulation class | ~ | Class B |
| Degree of protection | ~ | IP44 |
| Control Input | ~ | 0~10VDC / PWM |
| Signal Output | ~ | FG (Tach output ) |

Remarks:
Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized
Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel


Test condition:
Ⅰ.The test data is obtained under the specified environment conditions and installation mode
Ⅱ.Input Voltage---Operating voltage
Ⅲ.Temperature---Room temperature 25℃
Ⅴ.Humidity---65%RH
Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off
Ⅱ.Do not plug or unplug the fan lead plug when the fan is running
Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury
Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out
Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds
Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product
Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer
Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading
1. High Efficiency: The FD3G146-48GL-90 delivers 1513.9 m3/h at 328 Pa while drawing only 201.6W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.
2. Industrial-Grade Impeller: The 146mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.
3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).
4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.
5. Easy Installation and Maintenance: Compact 146mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.
Q1:What kind of payments do you support?
A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping
Q2.Will you provide samples?
A2: Sample is available and can be delivered within 10days
Q3:How can I choose a more suitable model?
A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.
Q4:How can I place the order?
A4: Usually quote you within 24 hours after we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.
Q5:About transportation
A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive.
Q6:How long is the warranty period?
A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.