FK3G175-1ALH-7A
| Nominal Voltage | VAC | 115 |
| Current draw | A | 0.6±10% |
| Speed(RPM) | min-1 | 2850±5% |
| Power consumption | W | 35±10% |
| Max. Air Flow | CFM / m3 /H | 320.3/544.3 |
| Max. Static Pressure | In.wg /Pa | 1.3/325 |
50pcs
When quiet operation is non-negotiable, the FK3G175-1ALH-7A plug fan delivers a superpower combination of 59.4 dB(A) sound pressure and a mere 35 W power draw, making it the ideal air mover for noise-sensitive spaces such as medical consulting rooms, laboratory fume hoods, office ventilation and residential HRV units. This 175 mm backward-curved centrifugal fan is driven by a BLDCEC72 electronically commutated motor rated at 115VAC (92-138V), 0.6 A, and 2850 RPM, so it can be plugged directly into North American and Japanese power systems without a step-down transformer. The glass-fiber reinforced polypropylene impeller keeps rotating mass low for fast spin-up and low vibration, while the die-cast aluminum end cap provides a rigid, corrosion-resistant motor mount. Air performance reaches 320.3 CFM (544.3 m3/h) at free air and 1.3 in.wg (325 Pa) maximum static pressure, enough to push through a modest filter bank or duct run in compact air-handling equipment. Speed is controlled via a 0-10V DC or PWM input, giving precise airflow modulation and further noise reduction at part load. The motor is electronically protected against lock-up and over-temperature, with Class B insulation and a 20AWG, 500 mm flying cable for simple installation. Bearing life exceeds 40,000 hours at 40 degrees C, and the fan carries CE and RoHS certification. Typical applications include fan coils, cleanroom FFUs, telecom cabinets, EV chargers and light commercial ventilation.
The FK3G175-1ALH-7A is a plug-in centrifugal fan built around a 175 mm diameter backward-curved impeller molded from glass-fiber reinforced polypropylene. The impeller uses a hub-and-shroud construction with a precisely balanced blade array that is statically and dynamically balanced to ISO 1940 G6.3, minimizing vibration and tonal noise at the 2850 RPM design point. The forward-swept blade exit angle is optimized for a steep pressure curve, yielding a maximum static pressure of 325 Pa (1.3 in.wg) and a free-air flow of 544.3 m3/h (320.3 CFM). The single-piece die-cast aluminum end cap houses the motor and incorporates the mounting flange, providing a stiff, non-resonant structure that contributes to the low 59.4 dB(A) sound level. The BLDCEC72 motor is a three-phase electronically commutated design with integrated rotor position sensing and a sinusoidal drive for smooth, low-torque-ripple operation. It is rated for 115VAC nominal (operating range 92-138V, 50/60 Hz), drawing 0.6 A and 35 W at full speed. Speed control accepts a 0-10V DC analog signal or a 25 kHz PWM input, with tach output and alarm output available on request; the control interface is isolated from the mains for safety. Electrical protection includes locked-rotor and over-temperature shutdown with automatic restart, and the motor is insulated to Class B with a dielectric strength of 1500 VAC for one minute. The 20AWG, 500 mm cable is stripped and tinned for direct connection to terminal blocks or a mating connector. Bearings are pre-lubricated sealed ball bearings rated for more than 40,000 hours L10 life at 40 degrees C ambient, and the rotor is supported in a dynamically balanced assembly to keep vibration below 2.8 mm/s RMS. The fan is designed for panel mounting with the impeller drawing air axially and discharging radially through the backward-curved blades, and it can be installed in any orientation. Quality control includes 100 percent run-in and hipot testing, plus sampling for airflow and noise per AMCA 210/300. The product complies with CE, RoHS and REACH, and is manufactured under an ISO 9001:2015 quality management system. With its combination of low power, low noise and 115VAC direct operation, this model is suited to fan coils, CRAC units, laboratory equipment, medical devices and residential ventilation systems where energy efficiency and acoustic comfort are paramount.
| AC Plug Fan | ![]() |
|
| Type | FK3G175-1ALH-7A | |
| Model | BLDCEC72 | |
| Nominal Voltage | VAC | 115 |
| Voltage range | VAC | 92~138 |
| Current draw | A | 0.6±10% |
| Speed(RPM) | min-1 | 2850±5% |
| Power consumption | W | 35±10% |
| Sound Pressure Level | dB(A) | 59.4±5% |
| Max. Air Flow | CFM / m3 /H | 320.3/544.3 |
| Max. Static Pressure | In.wg /Pa | 1.3/325 |
| Insulation class | ~ | Class B |
| Degree of protection | ~ | IP44 |
| Control Input | ~ | 0~10VDC / PWM |
| Signal Output | ~ | FG (Tach output ) |

Remarks:
Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized
Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel


Test condition:
Ⅰ.The test data is obtained under the specified environment conditions and installation mode
Ⅱ.Input Voltage---Operating voltage
Ⅲ.Temperature---Room temperature 25℃
Ⅴ.Humidity---65%RH
Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off
Ⅱ.Do not plug or unplug the fan lead plug when the fan is running
Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury
Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out
Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds
Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product
Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer
Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading
1. High Efficiency: The FK3G175-1ALH-7A delivers 544.3 m3/h at 325 Pa while drawing only 35W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.
2. Industrial-Grade Impeller: The 175mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.
3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).
4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.
5. Easy Installation and Maintenance: Compact 175mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.
Q1:What kind of payments do you support?
A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping
Q2.Will you provide samples?
A2: Sample is available and can be delivered within 10days
Q3:How can I choose a more suitable model?
A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.
Q4:How can I place the order?
A4: Usually quote you within 24 hours after we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.
Q5:About transportation
A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive.
Q6:How long is the warranty period?
A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.