Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

FD3G133-1AGL-70 EC Dual Inlet Centrifugal Blower 133mm 115V 857 m3/h

FD3G133-1AGL-70

Nominal Voltage VAC 115
Current draw A 1.5±10%
Speed(RPM) min-1  1500±5%
Power consumption W 105±10%
Max. Air Flow CFM / m3 /H 524.9/857.2
Max. Static Pressure In.wg /Pa 0.78/175

50pcs

Brand:
FANOVA
Spu:
FD3G133-1AGL-70
  • Overview
  • Recommended Products
Brief Description

Quiet enough to work beside, tough enough to work in a plant: the FD3G133-1AGL-70 is a dual inlet centrifugal blower whose 64 dB(A) sound floor lets it sit in occupied spaces rather than behind a mechanical room door. Two back-to-back galvanized steel impellers, each 133 mm across, push 524.9 CFM (857.2 m3/h) against up to 0.78 In.wg (175 Pa) of duct resistance, so the blower can carry long supply runs and still keep the noise signature below normal conversation level. The drive is a BLDCEC72 electronically commutated brushless motor with a 72 mm rotor, rated 105 W at 1500 RPM and drawing 1.5 A from a 115VAC supply that may swing anywhere from 92 to 138 VAC. Because the motor is DC electronically commutated, speed is set by a 0-10 VDC analog signal or a PWM input rather than by a triac, so there is no 60 Hz hum and no transformer needed for North American and Japanese 115 V panels: the unit wires straight into a standard branch circuit. Windings are insulated to Class F and the electronics are protected against locked-rotor, over-voltage, under-voltage and over-temperature conditions, while the dual ball bearings are rated for a 40,000 hour L10 service life at 40 degrees C ambient. The die-cast aluminum endcaps and housing hold the rotor rigidly and resist corrosion in humid air, and the galvanized steel impeller blades shrug off dust, grit and temperatures that would soften a plastic wheel. Typical installations include cleanroom return air, laboratory fume hood make-up, medical isolation rooms, quiet office ventilation, air handling unit fan sections replacing larger single-inlet wheels, and OEM equipment where a low acoustic footprint is a specification rather than a preference. The blower carries CE and RoHS marks and is built under an ISO 9001 quality system; UL recognition on the motor is available on request.

Product Specification

The FD3G133-1AGL-70 is built around a twin-inlet impeller assembly. Each side carries a 133 mm diameter centrifugal wheel formed from galvanized steel sheet, with the blades rolled and crimped into the backplate so the wheel stays balanced after thousands of hours of service. Galvanized construction gives the impeller a zinc coating that resists rust in condensate-laden airstreams, and unlike molded plastic it does not creep or soften when the airstream runs warm. The two wheels are mounted on a common shaft between die-cast aluminum endcaps; the aluminum housing, besides being lighter than cast iron, damps vibration and provides a stable bearing seat, which is part of why the acoustic output stays at 64 dB(A) at the duty point. Air enters from both sides and discharges through a single rectangular outlet, delivering 524.9 CFM (857.2 m3/h) free air and a maximum static pressure of 0.78 In.wg (175 Pa), a combination suited to medium-length duct runs, filters and plenum boxes. The motor is the BLDCEC72, a brushless DC electronically commutated machine with a 72 mm rotor diameter. It is rated 105 W at 1500 RPM on a 115VAC nominal supply that tolerates 92 to 138 VAC, drawing 1.5 A; the internal rectifier and inverter stage means no external transformer or VFD is required, and the input power factor stays high across the voltage band. Speed control is through a 0-10 VDC analog interface or a 25 kHz PWM input, with the option of a factory-set fixed speed; tach output and alarm output are available on the control harness. Electrical protection covers locked rotor, over-current, over-voltage, under-voltage and over-temperature shutdown, with automatic restart after the fault clears. Windings are Class F insulated and the motor is designed for a 40 degrees C ambient; the dual pre-lubricated ball bearings carry an L10 rating of 40,000 hours at that ambient, and the bearing bores are machined in the aluminum endcaps to keep shaft alignment true. The connection is a 20AWG lead set, 176 mm long, ending in flying leads for field termination. The blower is RoHS compliant and CE marked, manufactured under an ISO 9001 quality management system with routine hipot, insulation resistance and balance checks on every unit; UL recognition of the motor is offered as an option for North American OEM programs. Mounting is by the endcap flanges in any orientation, and the discharge can be rotated at build time to suit the duct layout.

Nominal Date
AC Dual Inlet Centrifugal Blower image.png
Type FD3G133-1AGL-70
Model BLDCEC72

 

Nominal Voltage VAC 115
Voltage range VAC 92~138
Current draw A 1.5±10%
Speed(RPM) min-1  1500±5%
Power consumption W 105±10%
Sound Pressure Level dB(A) 64±5%
Max. Air Flow CFM / m3 /H 524.9/857.2
Max. Static Pressure In.wg /Pa 0.78/175
Insulation class ~ Class B
Degree of protection ~ IP44
Control Input ~ 0~10VDC / PWM
Signal Output ~ FG (Tach output )
Connection diagram
image.png

Remarks:

Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized

Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel

Product drawing
image.png
Aerodynamic Performance Charts
image.png

Test condition:

Ⅰ.The test data is obtained under the specified environment conditions and installation mode

Ⅱ.Input Voltage---Operating voltage

Ⅲ.Temperature---Room temperature 25℃

Ⅴ.Humidity---65%RH

Safety Requirements

Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off

Ⅱ.Do not plug or unplug the fan lead plug when the fan is running

Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury

Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out

Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds

Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product

Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer

Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading

Advantages:

1. High Efficiency: The FD3G133-1AGL-70 delivers 857.2 m3/h at 175 Pa while drawing only 105W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.

2. Industrial-Grade Impeller: The 133mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.

3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).

4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.

5. Easy Installation and Maintenance: Compact 133mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.

FAQ

Q1:What kind of payments do you support?

A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping

Q2.Will you provide samples?

A2: Sample is available and can be delivered within 10days

Q3:How can I choose a more suitable model?

A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.

Q4:How can I place the order?

A4:  Usually quote you within 24 hours  after  we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.

Q5:About transportation

A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive. 

Q6:How long is the warranty period?

A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000