Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

FK3G280-2APK-60F EC Plug Fan 280mm 230V 3876 m3/h

FK3G280-2APK-60F

Nominal Voltage VAC 230
Current draw A 3.1±10%
Speed(RPM) min-1  3050±5%
Power consumption W 700±10%
Max. Air Flow CFM / m3 /H 2281.03/3876
Max. Static Pressure In.wg /Pa 4.16/1040

50pcs

Brand:
FANOVA
Spu:
FK3G280-2APK-60F
  • Overview
  • Recommended Products
Brief Description

When a single 280 mm impeller can deliver 3876 m3/h at up to 1040 Pa, the FK3G280-2APK-60F plug fan replaces whole banks of smaller AC fans in one 230VAC drop-in package. This backward-curved centrifugal unit is built around a glass-fiber reinforced propylene impeller on a 102 mm rotor BLDCEC102 EC motor, drawing 3.1 A and 700 W at 3050 RPM from any 184-270VAC supply. Its 1040 Pa ceiling is the headline for pressure-hungry designs: dense HEPA filter trains, long duct runs and multi-outlet plenums no longer force oversizing. Large 280 mm wheel diameter keeps tip speeds and noise in check (80.6 dB(A)) while moving the airflow, and the lightweight composite impeller cuts rotating mass for fast, smooth acceleration. Speed is commanded through a 0-10V/PWM EC interface with tach output, so airflow can be trimmed on site or tracked by a BMS. Motor protection and Class F insulation are standard, and the maintenance-free ball bearing set is rated for 40,000 hours at 40 degrees C. Typical duties include cleanroom FFU banks, AHU filter sections, lab exhaust, drying ovens, telecom shelters and new-energy cabinet cooling. CE and RoHS compliance, 18AWG 242 mm flying leads and die-cast aluminum endcap complete a package designed for panel mounting in air-handling equipment.

Product Specification

The FK3G280-2APK-60F is a backward-curved centrifugal plug fan assembled from a 280 mm diameter impeller molded in glass-fiber reinforced propylene, a material chosen to keep the wheel light yet stiff enough to hold blade geometry at 3050 RPM. Multiple backward-curved blades are bonded into a single hub-and-shroud assembly that is dynamically balanced after molding, limiting vibration and keeping the 80.6 dB(A) sound figure stable across the speed range. The wheel mounts directly on the shaft of a BLDCEC102 electronically commutated motor with a 102 mm rotor, a three-phase permanent-magnet design with integrated commutation electronics. Operating from a 230VAC nominal supply anywhere between 184 and 270VAC, the fan absorbs 3.1 A and 700 W at full speed, producing a maximum airflow of 3876 m3/h (2281 CFM) and a maximum static pressure of 1040 Pa (4.16 in.wg). Speed control is handled by an analog 0-10V input or a PWM signal, with a tachometer/frequency output available for closed-loop monitoring; the control cable and the 18AWG, 242 mm power leads exit the motor housing for direct termination in a control panel. The EC motor eliminates brush wear and slip losses, and its onboard electronics include over-current, over-voltage, locked-rotor and thermal protection. Insulation is Class F, and the motor is designed for continuous duty at ambient temperatures up to 40 degrees C. Mechanical support comes from a die-cast aluminum endcap that carries the bearing bores and provides a rigid, corrosion-resistant mounting face for the fan inlet ring; the bearing set is lubricated-for-life and rated for approximately 40,000 hours of L10 operation. Because the impeller is a composite, the unit resists dilute acids, cleaning agents and humidity better than untreated steel wheels and adds no galvanic corrosion risk in damp air streams. The plug-fan format, with the impeller and motor as one cartridge, allows the unit to be fitted into an AHU panel cut-out or a plenum wall without a separate bearing frame. The product is CE and RoHS compliant and is inspected for balance, dielectric strength, power draw and pressure performance before shipment.

Nominal Date
AC Plug Fan image.png
Type FK3G280-2APK-60F
Model BLDCEC102

 

Nominal Voltage VAC 230
Voltage range VAC 184~270
Current draw A 3.1±10%
Speed(RPM) min-1  3050±5%
Power consumption W 700±10%
Sound Pressure Level dB(A) 80.6±5%
Max. Air Flow CFM / m3 /H 2281.03/3876
Max. Static Pressure In.wg /Pa 4.16/1040
Insulation class ~ Class B
Degree of protection ~ IP44
Control Input ~ 0~10VDC / PWM
Signal Output ~ FG (Tach output )
Connection diagram
image.png

Remarks:

Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized

Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel

Product drawing
image.png
Aerodynamic Performance Charts
image.png

Test condition:

Ⅰ.The test data is obtained under the specified environment conditions and installation mode

Ⅱ.Input Voltage---Operating voltage

Ⅲ.Temperature---Room temperature 25℃

Ⅴ.Humidity---65%RH

Safety Requirements

Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off

Ⅱ.Do not plug or unplug the fan lead plug when the fan is running

Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury

Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out

Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds

Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product

Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer

Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading

Advantages:

1. High Efficiency: The FK3G280-2APK-60F delivers 3876 m3/h at 1040 Pa while drawing only 700W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.

2. Industrial-Grade Impeller: The 280mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.

3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).

4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.

5. Easy Installation and Maintenance: Compact 280mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.

FAQ

Q1:What kind of payments do you support?

A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping

Q2.Will you provide samples?

A2: Sample is available and can be delivered within 10days

Q3:How can I choose a more suitable model?

A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.

Q4:How can I place the order?

A4:  Usually quote you within 24 hours  after  we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.

Q5:About transportation

A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive. 

Q6:How long is the warranty period?

A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000