FK3G280-2APK-60
| Nominal Voltage | VAC | 230 |
| Current draw | A | 3.1±10% |
| Speed(RPM) | min-1 | 3050±5% |
| Power consumption | W | 700±10% |
| Max. Air Flow | CFM / m3 /H | 2281.03/3876 |
| Max. Static Pressure | In.wg /Pa | 4.16/1040 |
50pcs
When a single 280 mm impeller can deliver 3876 m3/h at up to 1040 Pa, the usual multi-fan array becomes unnecessary - that is the engineering premise behind the FK3G280-2APK-60 plug fan. Driven by a 700 W BLDCEC102 electronically commutated motor on 230VAC (operating window 184-270V), it reaches 3050 RPM and shifts 2281 CFM while holding 4.16 In.wg of static pressure, so one compact wheel replaces two or three smaller AC fans in the same plenum. The glass-fiber reinforced polypropylene impeller keeps rotating mass low, shortening spin-up and reducing bearing load, while the die-cast aluminum endcap ties the motor and impeller into a stiff, vibration-damped unit. Because the EC motor is speed-controllable across its full range, airflow can be trimmed to the duty point instead of being fixed by an AC tap, and the 230VAC input means the fan drops straight into existing single-phase cabinets with no transformer or VFD. Integrated electronics provide soft start, over-current and locked-rotor protection, thermal safeguarding and Class B insulation for long service in conditioned equipment rooms. The dual ball-bearing system is rated for continuous duty at elevated temperature, giving tens of thousands of maintenance-free hours at the nominal operating point. Typical installations are air-handling units, cleanroom and HEPA filter modules, rooftop ventilation packages, battery energy storage cabinets and data-center air movers, where high pressure capability and high flow are needed together. The unit is CE and RoHS compliant and built under ISO 9001 quality management, with the 18AWG 255 mm cable pre-terminated for fast panel wiring.
The impeller of the FK3G280-2APK-60 is a 280 mm diameter backward-curved centrifugal wheel molded in glass-fiber reinforced polypropylene. Backward-curved blades, over a dozen in number, are profiled to keep the airflow attached at high pressure ratios, which is why the fan can hold 1040 Pa while still moving 3876 m3/h at free delivery; the plastic-and-glass composite resists chemical attack, will not rust in humid airstreams and keeps the wheel light enough for 3050 RPM operation without excessive inertia. The wheel is balanced and mounted on the BLDCEC102 external-rotor motor, whose 102 mm rotor is integrated into the hub. Motor and impeller sit inside a die-cast aluminum endcap that serves as the structural backplate, heat sink and mounting interface, machined for concentricity so tip clearance stays uniform around the circumference. The EC motor's permanent-magnet rotor and three-phase stator are commutated electronically, producing 700 W at 230VAC nominal with a 184-270V tolerance so the fan rides through brownouts and overvoltage without tripping; current draw is 3.1 A at the rated point. Speed is set by a 0-10V DC analog input, PWM signal or onboard potentiometer, with tachometer output for monitoring; the drive offers soft start, over-current, over-temperature and locked-rotor protection, plus polarity and surge protection on the supply. Insulation is Class B and the winding is impregnated for moisture and vibration resistance. The shaft runs in two pre-lubricated ball bearings selected for continuous duty at 3050 RPM, with an L10 life exceeding 40,000 hours at the nominal point and ambient, and the bearing seats are damped to suppress rotor-borne noise, which measures 80.6 dB(A) at full speed. Electrical connection is an 18AWG cable, 255 mm long, factory-fitted for panel termination. The unit is CE marked, RoHS compliant and manufactured under ISO 9001, with routine hipot, insulation-resistance and balance checks on every unit.
| AC Plug Fan | ![]() |
|
| Type | FK3G280-2APK-60 | |
| Model | BLDCEC102 | |
| Nominal Voltage | VAC | 230 |
| Voltage range | VAC | 184~270 |
| Current draw | A | 3.1±10% |
| Speed(RPM) | min-1 | 3050±5% |
| Power consumption | W | 700±10% |
| Sound Pressure Level | dB(A) | 80.6±5% |
| Max. Air Flow | CFM / m3 /H | 2281.03/3876 |
| Max. Static Pressure | In.wg /Pa | 4.16/1040 |
| Insulation class | ~ | Class B |
| Degree of protection | ~ | IP44 |
| Control Input | ~ | 0~10VDC / PWM |
| Signal Output | ~ | FG (Tach output ) |

Remarks:
Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized
Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel


Test condition:
Ⅰ.The test data is obtained under the specified environment conditions and installation mode
Ⅱ.Input Voltage---Operating voltage
Ⅲ.Temperature---Room temperature 25℃
Ⅴ.Humidity---65%RH
Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off
Ⅱ.Do not plug or unplug the fan lead plug when the fan is running
Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury
Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out
Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds
Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product
Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer
Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading
1. High Efficiency: The FK3G280-2APK-60 delivers 3876 m3/h at 1040 Pa while drawing only 700W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.
2. Industrial-Grade Impeller: The 280mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.
3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).
4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.
5. Easy Installation and Maintenance: Compact 280mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.
Q1:What kind of payments do you support?
A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping
Q2.Will you provide samples?
A2: Sample is available and can be delivered within 10days
Q3:How can I choose a more suitable model?
A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.
Q4:How can I place the order?
A4: Usually quote you within 24 hours after we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.
Q5:About transportation
A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive.
Q6:How long is the warranty period?
A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.