FB3G310-24AL-90
| Nominal Voltage | VDC | 24 |
| Current draw | A | 5.0±10% |
| Speed(RPM) | min-1 | 1720±5% |
| Power consumption | W | 120±10% |
| Max. Air Flow | CFM / m3 /H | 1132.1/1923.7 |
| Max. Static Pressure | In.wg /Pa | 1.6/400 |
50pcs
Big-airflow duty does not have to mean big voltage: the FB3G310-24AL-90 backward curved centrifugal fan moves up to 1923.7 m3/h (1132.1 CFM) while running entirely on a 24VDC nominal supply (operating window 16 to 28VDC). That combination lets a single 310 mm impeller replace two or three smaller fans in a plenum or cabinet, cutting fan count, wiring runs and maintenance points, and it keeps the whole air path on safety extra-low voltage for solar arrays, battery rooms, off-grid telecom shelters and new-energy equipment racks where 230VAC is simply not available. Driving the impeller is a BLDCDC92 brushless DC motor rated 120 W at 1720 RPM, drawing 5.0 A and holding 1.6 in.wg (400 Pa) of static pressure - enough for a real filter stack or a long duct run without falling off the curve. The 310 mm die-cast aluminum impeller and matching die-cast aluminum endcap and housing give a stiff, dimensionally stable rotor that holds balance at 1720 RPM and shrugs off the heat that builds up inside enclosures. Control is by 0-10VDC or PWM speed signal, so the fan can track temperature, pressure or battery state instead of running flat out; protection and insulation are built to the usual IEC motor standards, and the dual ball-bearing set is rated for tens of thousands of hours of continuous duty. Typical applications include off-grid cooling, solar inverter cabinets, energy storage racks, DC ventilation plenums and industrial air handling on low-voltage buses. The unit carries CE and RoHS compliance and is produced under FANOVA's ISO 9001 quality system.
The FB3G310-24AL-90 is built around a 310 mm diameter backward curved impeller cast in aluminum alloy, with a blade count and curvature tuned for a broad, stable pressure characteristic rather than a single peak - the fan can be throttled by a filter or duct without collapsing into surge. The die-cast aluminum hub and the die-cast aluminum endcap and housing form a rigid rotating assembly that resists the thermal cycling common in outdoor and enclosure-mounted installations; the rotor diameter of 92 mm matches the BLDCDC92 motor family. The brushless DC motor is electronically commutated, using Hall-effect sensing and an integrated drive board to deliver 120 W at 1720 RPM from a 24VDC nominal bus that may float anywhere from 16 to 28VDC, drawing 5.0 A at full load. Because the speed is set electronically rather than by line frequency, the fan holds its operating point as the battery or DC bus voltage sags, which is exactly what off-grid and inverter-fed systems need. Speed control is accepted through a 0-10VDC analog input or a PWM duty signal, with tachometer output available for monitoring; the control leads and the 20AWG, 120 mm power cable exit the housing for direct termination into a terminal block or controller. The motor is insulated and protected to standard IEC practice, with locked-rotor and over-temperature protection on the drive. Bearings are a pair of preloaded ball bearings rated for extended continuous life at the rated speed, and the rotor is dynamically balanced to keep vibration low at 1720 RPM. Acoustic output is 67 dB(A) at the duty point, and the unit is CE and RoHS compliant, manufactured in FANOVA's ISO 9001 certified facility in Suzhou with routine performance and hipot testing on every batch.
| DC Backward Curved Centrifugal Fan | ![]() |
|
| Type | FB3G310-24AL-90 | |
| Model | BLDCDC92 | |
| Nominal Voltage | VDC | 24 |
| Voltage range | VDC | 16~28 |
| Current draw | A | 5.0±10% |
| Speed(RPM) | min-1 | 1720±5% |
| Power consumption | W | 120±10% |
| Sound Pressure Level | dB(A) | 67±5% |
| Max. Air Flow | CFM / m3 /H | 1132.1/1923.7 |
| Max. Static Pressure | In.wg /Pa | 1.6/400 |
| Insulation class | ~ | Class B |
| Degree of protection | ~ | IP44 |
| Control Input | ~ | 0~10VDC / PWM |
| Signal Output | ~ | FG (Tach output ) |

Remarks:
Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized
Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel


Test condition:
Ⅰ.The test data is obtained under the specified environment conditions and installation mode
Ⅱ.Input Voltage---Operating voltage
Ⅲ.Temperature---Room temperature 25℃
Ⅴ.Humidity---65%RH
Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off
Ⅱ.Do not plug or unplug the fan lead plug when the fan is running
Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury
Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out
Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds
Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product
Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer
Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading
1. High Efficiency: The FB3G310-24AL-90 delivers 1923.7 m3/h at 400 Pa while drawing only 120W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.
2. Industrial-Grade Impeller: The 310mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.
3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).
4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.
5. Easy Installation and Maintenance: Compact 310mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.
Q1:What kind of payments do you support?
A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping
Q2.Will you provide samples?
A2: Sample is available and can be delivered within 10days
Q3:How can I choose a more suitable model?
A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.
Q4:How can I place the order?
A4: Usually quote you within 24 hours after we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.
Q5:About transportation
A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive.
Q6:How long is the warranty period?
A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.