Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

FK3G220-48PL-95 DC Plug Fan 220mm 48V 1246 m3/h

FK3G220-48PL-95

Nominal Voltage VDC 48
Current draw A 3.0±10%
Speed(RPM) min-1  3500±5%
Power consumption W 144±10%
Max. Air Flow CFM / m3 /H 733.57/1246.5
Max. Static Pressure In.wg /Pa 3.6/900

50pcs

Brand:
FANOVA
Spu:
FK3G220-48PL-95
  • Overview
  • Recommended Products
Brief Description

The FK3G220-48PL-95 is a 220 mm backward-curved plug fan built for telecom and DC power rooms where the nominal -48VDC bus must drive high-restriction air paths without an inverter. Its standout capability is static pressure: the unit develops up to 3.6 in.wg (900 Pa) while still moving 733.57 CFM (1246.5 m3/h), so it can push through dense filter banks, long duct runs and multi-outlet plenums that stall ordinary axial fans. The impeller is molded from glass-fiber reinforced propylene, giving a lightweight, chemically resistant wheel that resists moisture and washdown aerosols and keeps starting torque low on the 48VDC rail. Drive comes from a BLDCDC92 brushless DC motor rated 144 W at 3.0 A across a 36 to 57VDC window, with sinusoidal commutation and integrated speed control via PWM or 0-10V input, so airflow can be trimmed to match DCIM load profiles. Winding insulation is Class F with Class B rise limits, and the electronics are reverse-polarity and over-current protected. Dual ball bearings rated for 70,000 hours at 40 degrees C carry the rotor, and the die-cast aluminum endcap doubles as a heat spreader for the drive board. At 3500 RPM the fan produces 74 dB(A), acceptable for unmanned equipment bays. Typical installations include -48VDC telecom cabinets, outdoor energy-storage enclosures, rectifier rooms and rail power modules. The fan carries CE and RoHS conformity and is manufactured under ISO 9001 with 100 percent run-in testing.

Product Specification

The FK3G220-48PL-95 is a 220 mm diameter backward-curved centrifugal plug fan supplied as a complete cartridge: impeller, external-rotor BLDCDC92 brushless DC motor, die-cast aluminum endcap and 500 mm flying lead. The impeller is injection molded in glass-fiber reinforced propylene, a formulation chosen for stiffness-to-weight ratio rather than metal substitution alone. The wheel carries a dense array of backward-curved blades that are continuously curved from inlet to tip; this geometry accelerates air radially and converts velocity into pressure efficiently, which is why the fan reaches 3.6 in.wg (900 Pa) at shutoff-region operation and 733.57 CFM (1246.5 m3/h) at free delivery. The reinforced polymer blades damp high-frequency blade-pass energy better than sheet metal, contributing to the 74 dB(A) sound level at 3500 RPM, and the material tolerates humidity, mild acids and alkaline cleaning agents found in battery and rectifier rooms. The rotor diameter is 92 mm, and the wheel is dynamically balanced to ISO 1940 G6.3 before final assembly. The external-rotor motor uses rare-earth magnets and a 48VDC-optimized winding; at 3.0 A and 144 W it delivers roughly 0.39 N.m of continuous torque with reserve for filter loading. Commutation is sinusoidal through an integrated drive board mounted inside the aluminum endcap, which acts as a heatsink and holds surface temperature rise below 40 K at rated load. Speed control accepts a 25 kHz PWM signal or a 0-10V analog reference, with tachometer and locked-rotor alarm outputs available on the lead; the input range is 36 to 57VDC, covering the full telecom -48VDC tolerance band including equalize charge excursions. Protection includes reverse-polarity blocking, over-current foldback, under-voltage lockout at 34VDC and thermal shutdown at 100 degrees C on the power stage. The motor is insulated to Class F with Class B temperature rise and tested at 500 VAC hipot for one minute. Dual pre-lubricated ball bearings, shielded on both sides, give an L10 life of 70,000 hours at 40 degrees C ambient; the outboard bearing is spring-preloaded to control axial play and reduce rumble at low speed. The die-cast aluminum endcap is powder-coated and drilled with a standard 4-hole flange pattern for drop-in mounting into plenums and cabinet walls; the impeller inlet ring is machined for a close radial clearance to limit recirculation. Electrical connection is a 20AWG, 500 mm four-conductor cable, stripped and tinned, carrying supply, ground, control and tach. The unit is CE marked, RoHS compliant and produced in an ISO 9001 facility with 100 percent end-of-line run-in, airflow sampling and hipot verification; each fan ships with a serialized test label. Operating range is -20 to 60 degrees C, and storage tolerance is -40 to 80 degrees C.

Nominal Date
DC Plug Fan image.png
Type FK3G220-48PL-95
Model BLDCDC92

 

Nominal Voltage VDC 48
Voltage range VDC 36~57
Current draw A 3.0±10%
Speed(RPM) min-1  3500±5%
Power consumption W 144±10%
Sound Pressure Level dB(A) 74±5%
Max. Air Flow CFM / m3 /H 733.57/1246.5
Max. Static Pressure In.wg /Pa 3.6/900
Insulation class ~ Class B
Degree of protection ~ IP44
Control Input ~ 0~10VDC / PWM
Signal Output ~ FG (Tach output )
Connection diagram
image.png

Remarks:

Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized

Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel

Product drawing
image.png
Aerodynamic Performance Charts
image.png

Test condition:

Ⅰ.The test data is obtained under the specified environment conditions and installation mode

Ⅱ.Input Voltage---Operating voltage

Ⅲ.Temperature---Room temperature 25℃

Ⅴ.Humidity---65%RH

Safety Requirements

Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off

Ⅱ.Do not plug or unplug the fan lead plug when the fan is running

Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury

Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out

Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds

Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product

Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer

Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading

Advantages:

1. High Efficiency: The FK3G220-48PL-95 delivers 1246.5 m3/h at 900 Pa while drawing only 144W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.

2. Industrial-Grade Impeller: The 220mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.

3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).

4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.

5. Easy Installation and Maintenance: Compact 220mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.

FAQ

Q1:What kind of payments do you support?

A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping

Q2.Will you provide samples?

A2: Sample is available and can be delivered within 10days

Q3:How can I choose a more suitable model?

A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.

Q4:How can I place the order?

A4:  Usually quote you within 24 hours  after  we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.

Q5:About transportation

A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive. 

Q6:How long is the warranty period?

A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000