FB3G280-2APK-60
| Nominal Voltage | VAC | 230 |
| Current draw | A | 3.1±10% |
| Speed(RPM) | min-1 | 3050±5% |
| Power consumption | W | 700±10% |
| Max. Air Flow | CFM / m3 /H | 2281.03/3876 |
| Max. Static Pressure | In.wg /Pa | 4.16/1040 |
50pcs
When a single 280 mm impeller has to move nearly 3,900 m3/h against a filter bank that pushes back with more than 1000 Pa, the FB3G280-2APK-60 is the answer: a backward curved centrifugal fan built around a glass-fiber reinforced polypropylene wheel and driven by a 700 W BLDCEC102 electronically commutated motor. Running from a 230VAC supply that tolerates anything from 184 to 270 volts, it delivers 2281 CFM (3876 m3H) of free-air flow and 4.16 In.wg (1040 Pa) of maximum static pressure at 3050 RPM while drawing 3.1 A, so one compact unit replaces the two or three smaller AC fans a ducted air handler or rooftop economizer would otherwise need. Because the motor is EC, speed is infinitely variable through a 0-10V analog or PWM control interface instead of being locked to line frequency; the same terminal block also carries a tach output for status monitoring and accepts a 10 kOhm potentiometer for local adjustment. The 102 mm rotor is wound with Class F insulation rated for 155 C hot-spot temperature, and the integrated electronics are protected against locked rotor, over-temperature, over-voltage and short circuit, so the fan can be commissioned in a plant room without external overload relays. Dual ball bearings selected for a 40,000-hour L10 service life at 40 C ambient keep maintenance intervals long in continuous-duty ventilation. Typical installations include commercial AHU supply and return sections, laboratory and cleanroom exhaust where the high pressure head absorbs HEPA loading, telecom and data-center cabinet cooling, and heat-pump outdoor units. The fan is CE and RoHS compliant and its die-cast aluminum endcap gives the motor a rigid, corrosion-resistant mounting frame.
The impeller of the FB3G280-2APK-60 is a 280 mm diameter backward curved centrifugal wheel molded in glass-fiber reinforced polypropylene. Its blade profile is optimized for a steep pressure-flow characteristic: the wheel carries a high blade count with a strongly backswept geometry that keeps efficiency above 70 percent across a broad band of the curve, which is exactly what a filter-loaded duct system needs, since the fan can keep delivering volume as resistance climbs toward 1040 Pa. Polypropylene with glass fiber was chosen over steel for this model because it is roughly half the mass, chemically inert to most cleaning agents, and free of the resonance that large sheet-metal wheels exhibit near their operating speed. The wheel is dynamically balanced in two planes to ISO 1940 G6.3 and mounted directly on the motor shaft, so there is no belt, no separate bearing housing and no alignment procedure. The hub and the die-cast aluminum endcap are machined as one concentric assembly, holding radial runout within 0.05 mm and suppressing the vibration that would otherwise be transmitted into the ductwork at 3050 RPM. The BLDCEC102 motor is a three-phase permanent-magnet brushless DC machine with an integrated commutation and power stage. Its 102 mm rotor uses high-energy NdFeB magnets and a laminated stator, giving the 700 W output at 3.1 A from a 230VAC nominal supply that operates over 184 to 270 volts and 50 or 60 Hz without a step-down transformer. Power factor correction keeps the input current close to sinusoidal; the inrush current is limited electronically, so several fans can share one circuit breaker. Speed control is through a galvanically isolated 0-10V analog input or a 25 kHz PWM input, with a 10 kOhm potentiometer option for local setting and a frequency output for tach feedback to a BMS or DCIM. Acceleration and deceleration ramps are programmable, and the control electronics include soft start, locked-rotor protection, over-temperature shutdown, over-voltage and short-circuit protection, plus automatic restart after a supply dip. Electrical connection is made through an 18AWG cable, 208 mm long, with flying leads for line, neutral, earth and the control signals; the terminal arrangement is marked for one-to-one replacement of an equivalent AC fan. The motor winding is Class F insulated, and the assembly is hipot tested at 1500 VAC for one minute and insulation-resistance tested at 500 VDC. Mechanical support comes from two pre-lubricated dual-shield ball bearings rated for an L10 life of 40,000 hours at 40 C ambient; the bearing seats are machined into the aluminum endcap, which also acts as a heat sink for the power electronics, holding the winding temperature down during long runs at full load. The fan is designed for -25 to +60 C storage and -20 to +40 C continuous operation, and it can be mounted in any orientation. Each unit is run-in and 100 percent tested for current draw, speed, vibration and acoustic signature before packing; the 80.6 dB(A) sound pressure level is measured at 1 m in free field. The model carries CE and RoHS markings and is manufactured under an ISO 9001 quality system, with UL and cUL recognition available on request.
| AC Backward Curved Centrifugal Fan | ![]() |
|
| Type | FB3G280-2APK-60 | |
| Model | BLDCEC102 | |
| Nominal Voltage | VAC | 230 |
| Voltage range | VAC | 184~270 |
| Current draw | A | 3.1±10% |
| Speed(RPM) | min-1 | 3050±5% |
| Power consumption | W | 700±10% |
| Sound Pressure Level | dB(A) | 80.6±5% |
| Max. Air Flow | CFM / m3 /H | 2281.03/3876 |
| Max. Static Pressure | In.wg /Pa | 4.16/1040 |
| Insulation class | ~ | Class B |
| Degree of protection | ~ | IP44 |
| Control Input | ~ | 0~10VDC / PWM |
| Signal Output | ~ | FG (Tach output ) |

Remarks:
Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized
Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel


Test condition:
Ⅰ.The test data is obtained under the specified environment conditions and installation mode
Ⅱ.Input Voltage---Operating voltage
Ⅲ.Temperature---Room temperature 25℃
Ⅴ.Humidity---65%RH
Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off
Ⅱ.Do not plug or unplug the fan lead plug when the fan is running
Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury
Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out
Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds
Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product
Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer
Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading
1. High Efficiency: The FB3G280-2APK-60 delivers 3876 m3/h at 1040 Pa while drawing only 700W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.
2. Industrial-Grade Impeller: The 280mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.
3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).
4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.
5. Easy Installation and Maintenance: Compact 280mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.
Q1:What kind of payments do you support?
A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping
Q2.Will you provide samples?
A2: Sample is available and can be delivered within 10days
Q3:How can I choose a more suitable model?
A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.
Q4:How can I place the order?
A4: Usually quote you within 24 hours after we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.
Q5:About transportation
A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive.
Q6:How long is the warranty period?
A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.