Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

FB3G250-2APS-70 EC Backward Curved Centrifugal Fan 250mm 230V 1240 m3/h

FB3G250-2APS-70

Nominal Voltage VAC 230
Current draw A 0.6±10%
Speed(RPM) min-1  2200±5%
Power consumption W 80±10%
Max. Air Flow CFM / m3 /H 730/1240.5
Max. Static Pressure In.wg /Pa 1.72/430

50pcs

Brand:
FANOVA
Spu:
FB3G250-2APS-70
  • Overview
  • Recommended Products
Brief Description

When a 250 mm backward-curved centrifugal fan is specified for noise-sensitive air handling, the FB3G250-2APS-70 from FANOVA answers with a measured 63.8 dB(A) sound pressure level while still delivering up to 1240.5 m3/h (730 CFM) at free air and 430 Pa (1.72 in.wg) of static pressure. The impeller is molded from glass-fiber reinforced propylene, a lightweight composite that keeps rotating mass low and blade passing tones soft, and it is paired with a die-cast aluminum endcap that damps vibration and holds bearing alignment. The BLDCEC72 electronically commutated motor draws only 80 W at 0.6 A from a 230 VAC supply that tolerates 184 to 270 V, so the unit can be connected directly to single-phase mains without an external transformer or VFD. Speed is set at 2200 RPM and is controlled through a 0-10 VDC or PWM interface, with tachometer feedback available for system monitoring. Insulation is Class B with Class F windings as an option, and the motor is protected against locked rotor, over-temperature and over-current; the ball-bearing set is rated for 40,000 hours at 40 C, giving long service intervals in continuous duty. Typical applications include medical and laboratory exhaust, cleanroom recirculation, office ventilation, fan-coil and air-handling units, and electronics cooling racks where low sound and low power draw matter. The fan carries CE and RoHS declarations and is manufactured under ISO 9001 quality management. For OEM and ODM programs, FANOVA can adapt cable length, connector type, control curve and mounting brackets to suit the host equipment.

Product Specification

The FB3G250-2APS-70 is a 250 mm diameter backward-curved centrifugal fan built around a glass-fiber reinforced propylene impeller. The wheel uses a hub-and-shroud construction with a hub ratio selected to balance inlet velocity against blade loading, and it carries 11 backward-curved blades with a logarithmic profile. Compared with a steel wheel of the same diameter, the composite impeller weighs roughly 40 percent less, which lowers start-up torque, reduces bearing load and shifts resonance away from the 2200 RPM operating point. The blade tips are trimmed to a small clearance against the inlet cone to limit recirculation, and the wheel is dynamically balanced in two planes to ISO 1940 G6.3 before assembly. The endcap and motor housing are die-cast aluminum, machined in one setup so that the bearing seats and stator bore stay concentric; this rigid structure also acts as a heat sink for the motor electronics. The 72 mm rotor diameter stator is a concentrated-winding design with permanent-magnet rotor, driven by the BLDCEC72 integrated commutation module. The electronics accept 230 VAC nominal with a full operating window of 184 to 270 V at 50/60 Hz, rectify the mains internally and generate a regulated DC bus, so fan performance stays stable during brownouts and line sag. At rated speed the motor consumes 80 W and 0.6 A, with efficiency above 80 percent at the design point. Speed control is through a 0-10 VDC analog input or a 25 kHz PWM input, both isolated from mains; a frequency output provides rotor-lock and speed feedback to a host controller, and the control terminals are brought out on the same 500 mm cable assembly as the supply. The cable is 20AWG, 500 mm long, with flying leads for field termination. Motor windings are Class B rated with Class F magnet wire available on request, and the insulation system is designed for a 1.5 kV dielectric withstand test. Protection features include locked-rotor shutdown, over-current limiting, over-temperature rollback and under-voltage lockout, all handled by the onboard microcontroller. The shaft runs in two pre-lubricated deep-groove ball bearings with a calculated L10 life of 40,000 hours at 40 C ambient; the bearing cavities are shielded to keep out dust and the shaft is grounded with a conductive brush to prevent electrical erosion from inverter-induced shaft currents. Airflow reaches 1240.5 m3/h (730 CFM) at free delivery and static pressure peaks at 430 Pa (1.72 in.wg), with the operating range covering ducted systems of moderate resistance. Sound pressure at one meter is 63.8 dB(A), and the composite wheel plus the aluminum housing together suppress the higher-order blade-passing harmonics that make small centrifugal fans sound harsh. The fan is rated for ambient temperatures from -20 to 60 C and can be mounted in any orientation. It complies with the CE marking directives for electromagnetic compatibility and low voltage, and with the RoHS substance restrictions; production follows ISO 9001 procedures with routine hipot, balance and performance testing on every unit.

Nominal Date
AC Backward Curved Centrifugal Fan image.png
Type FB3G250-2APS-70
Model BLDCEC72

 

Nominal Voltage VAC 230
Voltage range VAC 184~270
Current draw A 0.6±10%
Speed(RPM) min-1  2200±5%
Power consumption W 80±10%
Sound Pressure Level dB(A) 63.8±5%
Max. Air Flow CFM / m3 /H 730/1240.5
Max. Static Pressure In.wg /Pa 1.72/430
Insulation class ~ Class B
Degree of protection ~ IP44
Control Input ~ 0~10VDC / PWM
Signal Output ~ FG (Tach output )
Connection diagram
image.png

Remarks:

Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized

Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel

Product drawing
image.png
Aerodynamic Performance Charts
image.png

Test condition:

Ⅰ.The test data is obtained under the specified environment conditions and installation mode

Ⅱ.Input Voltage---Operating voltage

Ⅲ.Temperature---Room temperature 25℃

Ⅴ.Humidity---65%RH

Safety Requirements

Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off

Ⅱ.Do not plug or unplug the fan lead plug when the fan is running

Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury

Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out

Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds

Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product

Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer

Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading

Advantages:

1. High Efficiency: The FB3G250-2APS-70 delivers 1240.5 m3/h at 430 Pa while drawing only 80W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.

2. Industrial-Grade Impeller: The 250mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.

3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).

4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.

5. Easy Installation and Maintenance: Compact 250mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.

FAQ

Q1:What kind of payments do you support?

A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping

Q2.Will you provide samples?

A2: Sample is available and can be delivered within 10days

Q3:How can I choose a more suitable model?

A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.

Q4:How can I place the order?

A4:  Usually quote you within 24 hours  after  we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.

Q5:About transportation

A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive. 

Q6:How long is the warranty period?

A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000