Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

FB3G220-24PL-93 DC Backward Curved Centrifugal Fan 220mm 24V 812 m3/h

FB3G220-24PL-93

Nominal Voltage VDC 24
Current draw A 1.875±10%
Speed(RPM) min-1  2300±5%
Power consumption W 45±10%
Max. Air Flow CFM / m3 /H 477.9/812
Max. Static Pressure In.wg /Pa 1.34/334

50pcs

Brand:
FANOVA
Spu:
FB3G220-24PL-93
  • Overview
  • Recommended Products
Brief Description

The FB3G220-24PL-93 is a whisper-quiet, low-voltage backward curved centrifugal fan built for designers who need serious air movement without adding noise to the room. Running from a 24VDC supply (usable across 16 to 28VDC), it draws only 1.875 A and 45 W while turning a 220 mm glass-fiber reinforced polypropylene impeller at 2300 RPM, delivering up to 477.9 CFM (812 m3/h) of airflow against a maximum static pressure of 1.34 In.wg (334 Pa). The measured sound pressure is just 64 dB(A), a level that sits below normal conversation and makes the fan suitable for medical equipment, laboratory cabinets, office air handling and other spaces where acoustic comfort matters. A die-cast aluminum housing with a 92 mm rotor diameter gives the unit a rigid, dimensionally stable frame that resists vibration and keeps the blade-tip clearance consistent over a long service life. The BLDCDC92 brushless DC motor is electronically commutated, so speed can be trimmed with a 0-10V analog signal or a PWM input, letting the system match airflow to real demand instead of running flat out. Electrical safety is supported by Class B insulation and protection circuitry against locked-rotor and over-current conditions, while the 20AWG, 500 mm flying lead simplifies connection to a controller or DC bus. Because the fan operates on safe extra-low voltage, it is a natural fit for solar-powered ventilation, off-grid cooling skids, battery cabinets and new-energy enclosures where a 24VDC rail is already present. The molded composite impeller is lightweight and chemically resistant, cutting rotor inertia and start-up current compared with metal wheels of the same size. Units are produced under the FANOVA quality system with CE and RoHS compliance, and the fan is available for OEM and ODM customization of cable length, connector type and control interface.

Product Specification

The FB3G220-24PL-93 is a single-inlet backward curved centrifugal fan in the FANOVA FB3G220 series, configured around a 220 mm diameter impeller molded from glass-fiber reinforced polypropylene. The wheel carries a dense array of backward swept blades that are curved away from the direction of rotation, a geometry that produces a steep pressure-flow characteristic and keeps the operating point stable when the downstream duct resistance rises. Glass-fiber loading raises the stiffness of each blade so that tip deflection stays small even at the 2300 RPM design speed, preserving the close running clearance to the inlet cone and holding efficiency over the life of the unit. The hub and backplate are molded as one piece, which removes the riveted or welded joints found on fabricated metal wheels and eliminates a common source of imbalance and fatigue cracking. The impeller is dynamically balanced before assembly. The rotating assembly is carried in a die-cast aluminum housing with a 92 mm rotor envelope; the cast frame is stiffer than folded sheet-metal scrolls, damps vibration transmitted to the mounting panel and keeps bearing alignment true under belt or bracket loads. The motor is a BLDCDC92 brushless DC, electronically commutated machine with an integrated drive board, so commutation is handled without brushes, brush dust or sparking, and the only wearing parts are the shaft bearings. At the rated 24VDC input the fan consumes 1.875 A and 45 W, and the supply may range from 16 to 28VDC without damage, which allows operation from a nominal 24 V battery bank whose terminal voltage swings between charge and discharge states. Speed control is offered through a 0-10V analog interface and a PWM input, giving the system integrator a choice of control philosophies; a tachometer output can be specified to report actual rotor speed back to the host controller for closed-loop verification. The fan produces a maximum airflow of 477.9 CFM (812 m3/h) at free delivery and a maximum static pressure of 1.34 In.wg (334 Pa) at shut-off, and the useful working range extends across the mid-curve where ducted systems typically operate. Sound pressure at the standard measuring position is 64 dB(A), low enough for installation in occupied rooms, near laboratory instruments or inside medical carts. Electrical insulation is Class B, and the drive includes locked-rotor and over-current protection that limits winding heating if the impeller is obstructed. Connection is made through a 500 mm, 20AWG flying cable, and connector type, cable length and lead termination can be changed for OEM programs. The fan is designed for a long bearing service life under continuous duty and is intended for clean-air applications such as electronics cooling, air purification, heat-recovery ventilation, telecom cabinets, solar and off-grid ventilation systems, and battery thermal management in new-energy equipment. Each unit is functionally tested at the end of the line for speed, current, airflow and noise, and production follows the FANOVA quality management system with CE and RoHS declarations available on request.

Nominal Date
DC Backward Curved Centrifugal Fan image.png
Type FB3G220-24PL-93
Model BLDCDC92

 

Nominal Voltage VDC 24
Voltage range VDC 16~28
Current draw A 1.875±10%
Speed(RPM) min-1  2300±5%
Power consumption W 45±10%
Sound Pressure Level dB(A) 64±5%
Max. Air Flow CFM / m3 /H 477.9/812
Max. Static Pressure In.wg /Pa 1.34/334
Insulation class ~ Class B
Degree of protection ~ IP44
Control Input ~ 0~10VDC / PWM
Signal Output ~ FG (Tach output )
Connection diagram
image.png

Remarks:

Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized

Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel

Product drawing
image.png
Aerodynamic Performance Charts
image.png

Test condition:

Ⅰ.The test data is obtained under the specified environment conditions and installation mode

Ⅱ.Input Voltage---Operating voltage

Ⅲ.Temperature---Room temperature 25℃

Ⅴ.Humidity---65%RH

Safety Requirements

Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off

Ⅱ.Do not plug or unplug the fan lead plug when the fan is running

Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury

Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out

Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds

Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product

Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer

Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading

Advantages:

1. High Efficiency: The FB3G220-24PL-93 delivers 812 m3/h at 334 Pa while drawing only 45W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.

2. Industrial-Grade Impeller: The 220mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.

3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).

4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.

5. Easy Installation and Maintenance: Compact 220mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.

FAQ

Q1:What kind of payments do you support?

A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping

Q2.Will you provide samples?

A2: Sample is available and can be delivered within 10days

Q3:How can I choose a more suitable model?

A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.

Q4:How can I place the order?

A4:  Usually quote you within 24 hours  after  we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.

Q5:About transportation

A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive. 

Q6:How long is the warranty period?

A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000