FK3G175-48LH-70
| Nominal Voltage | VDC | 48 |
| Current draw | A | 0.85±10% |
| Speed(RPM) | min-1 | 3100±5% |
| Power consumption | W | 42±10% |
| Max. Air Flow | CFM / m3 /H | 319.2/542.4 |
| Max. Static Pressure | In.wg /Pa | 1.52/380 |
50pcs
Standing at just 42 watts yet delivering 542.4 m3/h (319.2 CFM) at free air and 380 Pa (1.52 in.wg) of static pressure, the FK3G175-48LH-70 is a compact plug fan engineered for ultra-low-power DC ventilation where every milliamp matters. This 48 VDC backward-curved centrifugal unit runs natively across a 36 to 57 VDC envelope and draws only 0.85 A, making it a natural fit for -48 VDC telecom racks, battery-backed cabinets, solar-assisted air handlers and off-grid cooling skids that cannot afford a 100 W-plus load. The impeller is a 175 mm glass-fiber reinforced propylene molding, a lightweight plastic rotor that resists dilute acids and cleaning agents while keeping start-up inertia low for frequent on/off cycling. A 72 mm rotor is matched to the BLDCDC72 brushless DC motor, electronically commutated and governed at 3100 RPM with closed-loop speed stability. Control is through the motor's DC interface, accepting a 0 to 10 V analog setpoint or PWM duty signal so airflow can be trimmed to demand rather than dumped through a damper. Electrical protection includes locked-rotor and polarity safeguards, insulation is Class B rated, and the die-cast aluminum endcap doubles as a heat spreader for the drive electronics. Bearings are pre-lubricated ball types rated for 40,000 hours at 40 C ambient, keeping the unit service-free through a typical five-year telecom life. At 67 dB(A) the acoustic signature stays below normal office conversation, which suits it to equipment rooms, lab cabinets, EV charging enclosures and inverter cooling. The fan carries CE and RoHS declarations and is manufactured under ISO 9001, with the 20AWG 500 mm flying lead ready for direct terminal-block connection. As an OEM/ODM platform, FANOVA can re-terminate, re-label or re-curve the FK3G175-48LH-70 to your cabinet's airflow path.
The FK3G175-48LH-70 is built around a 175 mm diameter backward-curved centrifugal impeller injection-molded from glass-fiber reinforced propylene. The plastic composition is chosen deliberately: it lowers rotating mass to roughly a third of an equivalent steel wheel, cuts bearing load at the 3100 RPM design point, and gives the blades enough chemical resistance to survive the mildly acidic condensate and cleaning sprays found in telecom shelters and outdoor cabinets. The blade array is a backward-curved, non-overloading profile, so the 42 W input power stays essentially flat as system resistance rises from free delivery toward the 380 Pa maximum static pressure, protecting the drive from overload on dirty filters. Airflow reaches 542.4 m3/h (319.2 CFM) at zero static and tapers predictably along the published curve. The rotor measures 72 mm and spins on the BLDCDC72 brushless DC motor, an electronically commutated three-phase design with integrated Hall sensing and a surface-mounted commutation stage. The motor accepts a 36 to 57 VDC input, draws 0.85 A at 48 VDC nominal, and is speed-controlled either by a 0 to 10 VDC analog reference or by a PWM duty-cycle input on the control lead; a tachometer output is available on request for DCIM or BMS integration. Electrical protection covers locked-rotor shutdown, reverse-polarity tolerance, over-current limiting and thermal fold-back of the drive. Insulation is Class B, and the winding is vacuum-impregnated to resist vibration. The die-cast aluminum endcap is not merely structural: it clamps the stator, carries the bearing seats and acts as the primary heat sink for the commutation electronics, holding junction temperatures in check even in sealed enclosures. Bearings are double-shielded, pre-lubricated ball bearings rated at 40,000 hours L10 at 40 C ambient, with a balanced rotor assembly that keeps vibration below 2.8 mm/s RMS. The electrical interface is a 500 mm flying lead of 20AWG wire, color-coded for power, ground and control, and can be supplied with a connector or longer harness to suit OEM line-side assembly. Acoustic output is 67 dB(A) at one meter, measured at nominal voltage and free inlet. Quality is assured under an ISO 9001 system, and the fan is CE marked and RoHS compliant; UL and CSA recognition can be arranged for volume programs. Mounting is via the die-cast aluminum flange, and the unit can be oriented in any axis without oil migration. The FK3G175-48LH-70 is supplied as a bare plug fan for ducted or plenum mounting, and FANOVA's engineering team supports airflow-path customization, harness changes and firmware speed curves for OEM and ODM projects.
| DC Plug Fan | ![]() |
|
| Type | FK3G175-48LH-70 | |
| Model | BLDCDC72 | |
| Nominal Voltage | VDC | 48 |
| Voltage range | VDC | 36~57 |
| Current draw | A | 0.85±10% |
| Speed(RPM) | min-1 | 3100±5% |
| Power consumption | W | 42±10% |
| Sound Pressure Level | dB(A) | 67±5% |
| Max. Air Flow | CFM / m3 /H | 319.2/542.4 |
| Max. Static Pressure | In.wg /Pa | 1.52/380 |
| Insulation class | ~ | Class B |
| Degree of protection | ~ | IP44 |
| Control Input | ~ | 0~10VDC / PWM |
| Signal Output | ~ | FG (Tach output ) |

Remarks:
Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized
Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel


Test condition:
Ⅰ.The test data is obtained under the specified environment conditions and installation mode
Ⅱ.Input Voltage---Operating voltage
Ⅲ.Temperature---Room temperature 25℃
Ⅴ.Humidity---65%RH
Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off
Ⅱ.Do not plug or unplug the fan lead plug when the fan is running
Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury
Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out
Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds
Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product
Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer
Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading
1. High Efficiency: The FK3G175-48LH-70 delivers 542.4 m3/h at 380 Pa while drawing only 42W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.
2. Industrial-Grade Impeller: The 175mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.
3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).
4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.
5. Easy Installation and Maintenance: Compact 175mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.
Q1:What kind of payments do you support?
A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping
Q2.Will you provide samples?
A2: Sample is available and can be delivered within 10days
Q3:How can I choose a more suitable model?
A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.
Q4:How can I place the order?
A4: Usually quote you within 24 hours after we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.
Q5:About transportation
A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive.
Q6:How long is the warranty period?
A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.