Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

FB3G250-2APS-21 EC Backward Curved Centrifugal Fan 250mm 230V 2200 m3/h

FB3G250-2APS-21

Nominal Voltage VAC 230
Current draw A 2.3±10%
Speed(RPM) min-1  3750±5%
Power consumption W 500±10%
Max. Air Flow CFM / m3 /H 1294.7/2200
Max. Static Pressure In.wg /Pa 6.08/1520

50pcs

Brand:
FANOVA
Spu:
FB3G250-2APS-21
  • Overview
  • Recommended Products
Brief Description

When a single 250 mm impeller must move as much air as two or three smaller AC fans while still pushing through dense HEPA media, the FB3G250-2APS-21 is the answer. Delivering a maximum airflow of 2200 m3/h (1294.7 CFM) and a peak static pressure of 1520 Pa (6.08 in.wg), this 230 VAC backward curved centrifugal fan replaces multiple lower-pressure units and simplifies ductwork in high-resistance air paths. The heart of the unit is a 102 mm BLDCEC102 electronically commutated motor rated 500 W at 3750 RPM, drawing 2.3 A from a wide 184-270 VAC supply so it rides through grid fluctuations without a step-down transformer. Speed is controlled via a 0-10 VDC or PWM interface, allowing precise balancing of airflow against filter loading. The impeller is molded from glass-fiber reinforced propylene, combining low mass with chemical resistance and cost efficiency, while the die-cast aluminum endcap provides rigid motor mounting and heat dissipation. Insulation is Class B with integrated thermal and locked-rotor protection, and the ball-bearing system is rated for 40,000 hours at 40 C ambient. Typical applications include cleanroom FFU stacks, industrial HEPA filter benches, fume hoods, and dense electronic enclosure cooling. The fan carries CE and RoHS certification and is manufactured under ISO 9001 quality management.

Product Specification

The FB3G250-2APS-21 is a backward curved centrifugal fan built around a 250 mm diameter impeller injection-molded from glass-fiber reinforced propylene. This material choice yields a lightweight rotor with good resistance to many industrial chemicals and a lower cost than metal alternatives, while the backward curved blade geometry - a single-piece hub and shroud with a high blade count optimized for pressure development - produces a steep pressure curve that holds airflow under heavy system resistance. The impeller is dynamically balanced to ISO 1940 G6.3 after assembly to keep vibration low at the 3750 RPM design speed. The motor is a BLDCEC102 outer-rotor electronically commutated design with a 102 mm rotor diameter, rated 500 W and 2.3 A at 230 VAC nominal. Its wide input range of 184 to 270 VAC means the fan can operate directly on nominal 230 V single-phase mains without a separate transformer, and internal power factor correction and soft-start circuitry limit inrush current. Speed control is available through a 0-10 VDC analog input or a PWM signal, with tachometer output for speed monitoring; the control electronics are housed in the die-cast aluminum endcap, which also serves as the motor heat sink and provides a rigid mounting interface. Electrical connection is via a 500 mm, 18 AWG cable with flying leads for mains, control and tach signals. Protection features include integrated thermal overload and locked-rotor protection, Class B insulation, and a ball-bearing system rated for 40,000 hours L10 life at 40 C ambient. The fan is designed for 230 VAC 50/60 Hz operation and produces a sound pressure level of 86.2 dB(A) at maximum speed, which is typical for a high-pressure 500 W unit and can be reduced by operating at lower speed where the application allows. The die-cast aluminum endcap and the impeller material combination keep the rotating mass low, reducing bearing loads and start-up stresses. The FB3G250-2APS-21 is intended for applications requiring high airflow against high static pressure, such as cleanroom fan filter units, HEPA filter housings, laboratory fume hoods, industrial air handling units, and dense electronics cooling. Each unit is factory tested for voltage withstand, insulation resistance and performance, and the product is CE and RoHS compliant, manufactured in an ISO 9001 certified facility.

Nominal Date
AC Backward Curved Centrifugal Fan image.png
Type FB3G250-2APS-21
Model BLDCEC102

 

Nominal Voltage VAC 230
Voltage range VAC 184~270
Current draw A 2.3±10%
Speed(RPM) min-1  3750±5%
Power consumption W 500±10%
Sound Pressure Level dB(A) 86.2±5%
Max. Air Flow CFM / m3 /H 1294.7/2200
Max. Static Pressure In.wg /Pa 6.08/1520
Insulation class ~ Class B
Degree of protection ~ IP44
Control Input ~ 0~10VDC / PWM
Signal Output ~ FG (Tach output )
Connection diagram
image.png

Remarks:

Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized

Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel

Product drawing
image.png
Aerodynamic Performance Charts
image.png

Test condition:

Ⅰ.The test data is obtained under the specified environment conditions and installation mode

Ⅱ.Input Voltage---Operating voltage

Ⅲ.Temperature---Room temperature 25℃

Ⅴ.Humidity---65%RH

Safety Requirements

Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off

Ⅱ.Do not plug or unplug the fan lead plug when the fan is running

Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury

Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out

Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds

Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product

Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer

Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading

Advantages:

1. High Efficiency: The FB3G250-2APS-21 delivers 2200 m3/h at 1520 Pa while drawing only 500W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.

2. Industrial-Grade Impeller: The 250mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.

3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).

4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.

5. Easy Installation and Maintenance: Compact 250mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.

FAQ

Q1:What kind of payments do you support?

A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping

Q2.Will you provide samples?

A2: Sample is available and can be delivered within 10days

Q3:How can I choose a more suitable model?

A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.

Q4:How can I place the order?

A4:  Usually quote you within 24 hours  after  we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.

Q5:About transportation

A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive. 

Q6:How long is the warranty period?

A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000