FK3G220-48PL-92
| Nominal Voltage | VDC | 48 |
| Current draw | A | 1.65±10% |
| Speed(RPM) | min-1 | 2760±5% |
| Power consumption | W | 80±10% |
| Max. Air Flow | CFM / m3 /H | 577.02/980.5 |
| Max. Static Pressure | In.wg /Pa | 1.94/485 |
50pcs
When a telecom cabinet or DCIM-managed rack needs a compact, low-power air mover that runs directly from a 48VDC bus, the FK3G220-48PL-92 plug fan is engineered to slot in without an AC inverter stage. Its headline advantage is a power draw of only 80 W at the design point, making it one of the most energy-frugal 220 mm backward-curved impellers in the FANOVA range, while still delivering 577 CFM (980 m3/h) of free air and 1.94 in.wg (485 Pa) of static pressure. The impeller is molded from glass-fiber reinforced propylene, a material chosen to keep rotating mass low so the 92 mm rotor can accelerate quickly and run smoothly at 2760 RPM. Drive comes from a BLDCDC92 brushless DC motor with integrated commutation electronics, accepting a 36 to 57VDC input window so nominal -48V telecom plants, battery strings and 48V DC microgrids all fall inside the safe operating envelope. Speed is set through a 0-10V analog or PWM control interface, allowing the fan to be throttled by a DCIM controller or thermal sensor rather than running at full tilt continuously. Electrical safety is covered by Class B insulation and locked-rotor and reverse-polarity protection, and the dual ball-bearing system is rated for 70,000 hours at 40 degrees C, giving long service intervals in unattended cabinets. Typical installations include telecom base stations, edge data closets, switchgear enclosures, battery thermal management and industrial DC power distribution, and the unit carries CE and RoHS declarations with optional UL recognition on request.
The FK3G220-48PL-92 is a 220 mm backward-curved centrifugal plug fan built around a glass-fiber reinforced propylene impeller. The single-piece molded impeller carries a dense array of backward-curved blades that are aerodynamically profiled to suppress flow separation at the trailing edge, which is why the fan reaches 485 Pa of static pressure without the tonal noise penalty typical of aluminum wheels. Because the propylene compound is roughly one-third the density of die-cast aluminum, the rotor inertia is low; the BLDCDC92 motor can therefore ramp from standstill to 2760 RPM in well under a second, and the lower mass reduces bearing loads during repeated start-stop cycles. The impeller is dynamically balanced to ISO 1940 G6.3 before assembly, and the hub is secured to the motor shaft with a machined collet to prevent fretting. The stationary endcap and venturi housing are die-cast aluminum, machined on CNC centers to hold concentricity between the impeller tip and the inlet orifice, a tolerance that directly controls the pressure-flow curve repeatability from unit to unit. Motor technology is a three-phase brushless DC topology with surface-mounted permanent magnets on the 92 mm rotor and a six-step or sinusoidal commutation stage integrated in the rear electronics cavity. The controller accepts 36 to 57VDC and draws 1.65 A at the 48VDC nominal rating, producing 80 W of shaft power at the design point. Speed command is via a 0-10V analog input or a 25 kHz PWM signal, with a tachometer output for closed-loop monitoring by a DCIM or PLC; the control harness is a 500 mm 20AWG cable with a molded connector, and separate power leads are color-coded for polarity. Protection features include locked-rotor shutdown with automatic restart, reverse-polarity blocking, over-current limiting and thermal fold-back of the drive stage. Insulation is Class B, and the winding is vacuum-impregnated to resist vibration and moisture. The bearing set consists of two pre-lubricated dual-shield ball bearings rated L10 at 70,000 hours at 40 degrees C ambient; the outboard bearing is seated in a rubber isolator that damps the 2760 RPM rotational order before it reaches the aluminum housing, contributing to the 71.4 dB(A) sound pressure level measured at 1 m. The fan is designed for horizontal or vertical panel-mount installation through a square cutout, retained by four M4 screws, and weighs approximately 1.1 kg. Quality control includes 100 percent end-of-line run-in at 48VDC for 30 minutes with speed, current and vibration signature recorded, plus hi-pot testing at 500 VAC. The product is CE marked and RoHS compliant, with UL recognition available as an option, and is manufactured in a facility certified to ISO 9001 and ISO 14001.
| DC Plug Fan | ![]() |
|
| Type | FK3G220-48PL-92 | |
| Model | BLDCDC92 | |
| Nominal Voltage | VDC | 48 |
| Voltage range | VDC | 36~57 |
| Current draw | A | 1.65±10% |
| Speed(RPM) | min-1 | 2760±5% |
| Power consumption | W | 80±10% |
| Sound Pressure Level | dB(A) | 71.4±5% |
| Max. Air Flow | CFM / m3 /H | 577.02/980.5 |
| Max. Static Pressure | In.wg /Pa | 1.94/485 |
| Insulation class | ~ | Class B |
| Degree of protection | ~ | IP44 |
| Control Input | ~ | 0~10VDC / PWM |
| Signal Output | ~ | FG (Tach output ) |

Remarks:
Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized
Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel


Test condition:
Ⅰ.The test data is obtained under the specified environment conditions and installation mode
Ⅱ.Input Voltage---Operating voltage
Ⅲ.Temperature---Room temperature 25℃
Ⅴ.Humidity---65%RH
Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off
Ⅱ.Do not plug or unplug the fan lead plug when the fan is running
Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury
Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out
Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds
Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product
Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer
Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading
1. High Efficiency: The FK3G220-48PL-92 delivers 980.5 m3/h at 485 Pa while drawing only 80W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.
2. Industrial-Grade Impeller: The 220mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.
3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).
4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.
5. Easy Installation and Maintenance: Compact 220mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.
Q1:What kind of payments do you support?
A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping
Q2.Will you provide samples?
A2: Sample is available and can be delivered within 10days
Q3:How can I choose a more suitable model?
A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.
Q4:How can I place the order?
A4: Usually quote you within 24 hours after we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.
Q5:About transportation
A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive.
Q6:How long is the warranty period?
A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.