Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

FK3G280-4APK-60 EC Plug Fan 280mm 380V 3876 m3/h

FK3G280-4APK-60

Nominal Voltage VAC 380
Current draw A 1.1±10%
Speed(RPM) min-1  3050±5%
Power consumption W 700±10%
Max. Air Flow CFM / m3 /H 2281.03/3876
Max. Static Pressure In.wg /Pa 4.16/1040

50pcs

Brand:
FANOVA
Spu:
FK3G280-4APK-60
  • Overview
  • Recommended Products
Brief Description

When a single 280 mm impeller can move 3876 m3/h against 1040 Pa of system resistance, the engineering conversation shifts from adding fans to replacing banks of them. The FK3G280-4APK-60 is a backward-curved plug fan built around exactly that premise: one 700 W electronically commutated unit delivering the airflow of several smaller AC fans while consuming a fraction of their combined power. Its glass-fiber reinforced propylene impeller is molded as a single lightweight rotor, so the mass that has to accelerate at every start is low, bearing loads stay modest, and the die-cast aluminum endcap holds the motor and impeller concentric under continuous duty. The BLDCEC102 motor runs from 380VAC three-phase supply and tolerates a 304 VAC floor, keeping stable operation through brownouts and long cable runs on rooftop and industrial installations. Speed is commanded at 3050 RPM through a 0-10 VDC or PWM interface, letting a BAS or standalone controller trim airflow to actual demand instead of dumping excess volume through a damper. Insulation is Class F with thermal protection embedded in the winding, and the 18AWG, 255 mm flying lead simplifies wiring inside compact plenum boxes. Acoustic output is held to 80.6 dB(A) at full speed, a figure that falls quickly as the EC drive is turned down. Typical installations include air handling units, cleanroom recirculation, data center air handlers, paint booth exhaust and OEM ventilation packages, and the fan carries CE and RoHS compliance for export programs. For buyers consolidating fan counts, this plug fan is the high-flow, high-head anchor of the FK3G280 range.

Product Specification

The FK3G280-4APK-60 is a 280 mm backward-curved centrifugal plug fan assembled as a drop-in module for AHU and OEM air-movement panels. Its impeller is injection molded from glass-fiber reinforced propylene, a material chosen for a high stiffness-to-weight ratio: the blade set holds its aerofoil profile at 3050 RPM without the tip deflection that would erode efficiency, while the low rotating mass reduces startup current and vibration. The backward-curved blade geometry is optimized for a steep pressure-flow characteristic, which is why the unit reaches 1040 Pa maximum static pressure yet still passes 3876 m3/h (2281 CFM) at free delivery. This combination of high flow and high head lets one fan serve duct runs and dense filter banks that would otherwise require two or three forward-curved units, cutting panel space, wiring and maintenance points. The rotor is driven by a BLDCEC102 brushless DC motor with integrated commutation electronics, operating from a 380VAC three-phase supply with a minimum of 304 VAC and drawing 1.1 A at rated load. Power factor correction and soft-start are built into the drive, so inrush is limited and multiple fans can share a supply without staggered contactors. Speed control accepts a 0-10 VDC analog signal or a PWM input, with tachometer output available for verification and fault reporting to a building management system; the control loop holds commanded speed within tight tolerance as static pressure varies, which is what makes demand-based ventilation practical. Electrical protection includes Class F insulation rated for 155 C hotspot temperature and thermal overload sensing in the stator winding, allowing the fan to run in hot plenum and return-air positions. The motor shaft turns in sealed, pre-lubricated ball bearings selected for an L10 life exceeding 40,000 hours at 40 C ambient, and the die-cast aluminum endcap acts as both bearing housing and heat sink, drawing motor losses into the airstream. The impeller is dynamically balanced to ISO 1940 G6.3 before assembly, keeping vibration low enough for ceiling-mounted and duct-adjacent installations. Electrical connection is made through an 18AWG cable with a 255 mm free length, long enough to reach a local terminal box without splicing inside the fan throat. The housing and endcap are die-cast aluminum for corrosion resistance and dimensional stability, and the assembly is rated for operation from -20 C to +60 C. Every unit is hipot tested, run-in and checked for current draw, speed accuracy and vibration before packing, and the series is CE marked and RoHS compliant. Applications include air handling units, cleanroom recirculation, data center cooling, laboratory exhaust, paint booth ventilation and industrial process air, where the 80.6 dB(A) sound pressure at full speed and the lower levels achieved under EC turndown suit occupied buildings.

Nominal Date
AC Plug Fan image.png
Type FK3G280-4APK-60
Model BLDCEC102

 

Nominal Voltage VAC 380
Voltage range VAC 304
Current draw A 1.1±10%
Speed(RPM) min-1  3050±5%
Power consumption W 700±10%
Sound Pressure Level dB(A) 80.6±5%
Max. Air Flow CFM / m3 /H 2281.03/3876
Max. Static Pressure In.wg /Pa 4.16/1040
Insulation class ~ Class B
Degree of protection ~ IP44
Control Input ~ 0~10VDC / PWM
Signal Output ~ FG (Tach output )
Connection diagram
image.png

Remarks:

Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized

Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel

Product drawing
image.png
Aerodynamic Performance Charts
image.png

Test condition:

Ⅰ.The test data is obtained under the specified environment conditions and installation mode

Ⅱ.Input Voltage---Operating voltage

Ⅲ.Temperature---Room temperature 25℃

Ⅴ.Humidity---65%RH

Safety Requirements

Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off

Ⅱ.Do not plug or unplug the fan lead plug when the fan is running

Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury

Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out

Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds

Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product

Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer

Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading

Advantages:

1. High Efficiency: The FK3G280-4APK-60 delivers 3876 m3/h at 1040 Pa while drawing only 700W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.

2. Industrial-Grade Impeller: The 280mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.

3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).

4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.

5. Easy Installation and Maintenance: Compact 280mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.

FAQ

Q1:What kind of payments do you support?

A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping

Q2.Will you provide samples?

A2: Sample is available and can be delivered within 10days

Q3:How can I choose a more suitable model?

A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.

Q4:How can I place the order?

A4:  Usually quote you within 24 hours  after  we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.

Q5:About transportation

A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive. 

Q6:How long is the warranty period?

A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000