Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

FK3G175-24LH-7F DC Plug Fan 175mm 24V 798 m3/h

FK3G175-24LH-7F

Nominal Voltage VDC 24
Current draw A 4.0±10%
Speed(RPM) min-1  4250±5%
Power consumption W 96±10%
Max. Air Flow CFM / m3 /H 939.4/798.1
Max. Static Pressure In.wg /Pa 2.93/731

50pcs

Brand:
FANOVA
Spu:
FK3G175-24LH-7F
  • Overview
  • Recommended Products
Brief Description

The FK3G175-24LH-7F is a low-voltage DC plug fan engineered for two jobs at once: it delivers up to 731 Pa (2.93 in.wg) of static pressure while drawing only 96 W from a 24VDC supply. That combination of high pressure and ultra-low power makes it a natural fit for battery-backed and off-grid air systems, where every watt is drawn from a solar module, a DC microgrid or a lithium pack rather than a wall outlet. Operating across 16 to 28VDC at a nominal 4.0 A, the fan spins a 175 mm glass-fiber reinforced polypropylene impeller to 4250 RPM and moves 939.4 CFM (798.1 m3H) at free air. The impeller's molded plastic construction keeps rotating mass low, so the BLDCDC72 brushless DC motor reaches working speed quickly and the bearings carry a lighter load than a comparable metal wheel would impose, which supports a long service life in continuous-duty equipment. Speed is commanded through the motor's DC control interface, letting the host controller trim airflow to demand instead of throttling with a mechanical damper. The die-cast aluminum endcap and housing hold the rotor on a rigid 72 mm center, and the fan terminates in a 500 mm 20AWG cable for direct wiring into a cabinet or duct plenum. Typical installations include telecom and outdoor enclosures, solar inverter cooling, refrigerated transport, air purifiers with dense filter media, and laboratory or medical carts that run on 24V battery rails. The unit is produced under FANOVA's Suzhou manufacturing and quality system with CE and RoHS compliance.

Product Specification

The impeller of the FK3G175-24LH-7F is a backward-curved centrifugal wheel measuring 175 mm in diameter, molded in glass-fiber reinforced polypropylene. The fiber loading raises the stiffness of each blade so that tip deflection stays small at the 4250 RPM design point, and the backward-curved blade profile gives the wheel a rising pressure characteristic that tolerates the resistance of long duct runs and loaded filters. Because the wheel is injection molded, blade spacing and surface finish repeat from unit to unit, keeping the acoustic signature consistent; the fan is rated at 73 dB(A). The wheel is mounted on a 72 mm rotor and enclosed by a die-cast aluminum endcap and housing, which provide the dimensional stability needed to hold tight tip clearance and act as a heat path away from the motor. At the heart of the unit is the BLDCDC72 brushless DC motor, an electronically commutated design with integrated drive electronics. It accepts a 24VDC nominal supply anywhere from 16 to 28VDC, so it rides through the voltage sag of a discharging battery string without dropping out, and it draws 4.0 A at rated load for 96 W of input power. Speed is set by a DC control signal through the motor's control interface, allowing stepless adjustment from standstill to 4250 RPM and enabling the host system to close a loop on temperature, pressure or air quality. The motor is designed for continuous duty with Class B insulation practice and electronic protection against over-current, locked rotor and reverse polarity. Mechanical support comes from precision ball bearings selected for low-vibration running and long L10 life at the rated speed. The complete assembly weighs little for its output, and the rotating group is balanced after assembly to keep vibration low. Electrical connection is made through a 500 mm lead of 20AWG cable, factory-fitted and strain-relieved at the housing exit, suitable for direct termination in a control cabinet or junction box. The FK3G175-24LH-7F is built in FANOVA's Suzhou facility under a quality system covering incoming material inspection, in-process balancing and end-of-line performance testing of airflow, static pressure, current and noise, and it is supplied in CE and RoHS compliant configuration. With 939.4 CFM and 731 Pa available from a 96 W, 24V package, it replaces larger AC blowers in solar inverter cooling, outdoor telecom cabinets, rail and marine ventilation, and filter-equipped air treatment equipment where low-voltage safety and low current draw are decisive.

Nominal Date
DC Plug Fan image.png
Type FK3G175-24LH-7F
Model BLDCDC72

 

Nominal Voltage VDC 24
Voltage range VDC 16~28
Current draw A 4.0±10%
Speed(RPM) min-1  4250±5%
Power consumption W 96±10%
Sound Pressure Level dB(A) 73±5%
Max. Air Flow CFM / m3 /H 939.4/798.1
Max. Static Pressure In.wg /Pa 2.93/731
Insulation class ~ Class B
Degree of protection ~ IP44
Control Input ~ 0~10VDC / PWM
Signal Output ~ FG (Tach output )
Connection diagram
image.png

Remarks:

Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized

Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel

Product drawing
image.png
Aerodynamic Performance Charts
image.png

Test condition:

Ⅰ.The test data is obtained under the specified environment conditions and installation mode

Ⅱ.Input Voltage---Operating voltage

Ⅲ.Temperature---Room temperature 25℃

Ⅴ.Humidity---65%RH

Safety Requirements

Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off

Ⅱ.Do not plug or unplug the fan lead plug when the fan is running

Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury

Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out

Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds

Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product

Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer

Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading

Advantages:

1. High Efficiency: The FK3G175-24LH-7F delivers 798.1 m3/h at 731 Pa while drawing only 96W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.

2. Industrial-Grade Impeller: The 175mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.

3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).

4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.

5. Easy Installation and Maintenance: Compact 175mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.

FAQ

Q1:What kind of payments do you support?

A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping

Q2.Will you provide samples?

A2: Sample is available and can be delivered within 10days

Q3:How can I choose a more suitable model?

A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.

Q4:How can I place the order?

A4:  Usually quote you within 24 hours  after  we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.

Q5:About transportation

A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive. 

Q6:How long is the warranty period?

A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000