FK3G190-2AGL-90
| Nominal Voltage | VAC | 230 |
| Current draw | A | 1.2±10% |
| Speed(RPM) | min-1 | 4000±5% |
| Power consumption | W | 155±10% |
| Max. Air Flow | CFM / m3 /H | 727.5/1236.2 |
| Max. Static Pressure | In.wg /Pa | 2.96/740 |
50pcs
When a duct run is long, a filter bank is dense, or a plenum must push air through several outlets, the limiting factor is rarely flow at free delivery; it is pressure at the working point. The FK3G190-2AGL-90 is built for exactly those duties, pairing a 190 mm galvanized steel backward-curved impeller with a 92 mm rotor BLDCEC92 motor to reach a maximum static pressure of 2.96 In.wg (740 Pa) while still moving up to 727.5 CFM (1236.2 m3H). Because the motor is electronically commutated, it runs directly from 230VAC mains anywhere in the 184 to 277V band with no external transformer, and it draws only 1.2 A at 4000 RPM for 155 W of input power, keeping the pressure head available without the losses of an AC induction plus VFD package. Speed is set by a 0 to 10V analog signal or a PWM input through the integrated control interface, so a commissioning engineer can dial the fan to the exact operating point of the system instead of bleeding excess pressure away with a damper. The steel impeller is the durability story here: galvanized sheet resists corrosion and abrasion in dusty or humid airstreams far better than molded plastic, and it holds its blade geometry when the fan is run continuously at the top of its speed range. Insulation is Class F with protection against overload and locked-rotor conditions, and the ball bearing set is rated for 40,000 hours at 40 degrees C ambient, giving a realistic service interval for air-handling units, cleanroom return plenums, laboratory exhaust and telecom cabinet cooling. At 73 dB(A) the unit is intended for plant rooms and equipment compartments rather than occupied spaces. CE and RoHS compliance, together with ISO 9001 controlled production, make the FK3G190-2AGL-90 straightforward to specify as a drop-in EC replacement for fixed-speed AC plug fans.
The impeller of the FK3G190-2AGL-90 is a 190 mm diameter backward-curved centrifugal wheel formed from galvanized steel sheet, with blades rolled to a constant curvature and riveted or crimped into the backplate and shroud so that tip clearance stays uniform around the full circumference. Backward-curved blading is chosen because its rising pressure characteristic is non-overloading: as system resistance increases, shaft power falls rather than climbs, which protects the motor when a filter loads up or a damper closes. The galvanized zinc coating provides sacrificial corrosion protection and resistance to the fine abrasive dust common in return-air and industrial ventilation paths, and the steel construction tolerates higher airstream temperatures than thermoplastic wheels of the same size. The wheel is dynamically balanced after assembly, then mounted on a machined hub and clamped to the motor shaft, keeping vibration low at the 4000 RPM design point.
Drive is provided by a BLDCEC92 electronically commutated motor with a 92 mm rotor diameter. The rotor uses permanent magnets and the stator is wound for three-phase operation, with a dedicated commutation controller converting the incoming AC supply to the DC link internally. Compared with an AC induction fan of similar output, the EC topology removes slip losses and allows the speed to be trimmed continuously, which is why the complete assembly delivers 155 W of input power at 1.2 A on a 230VAC nominal supply. The wide operating window of 184 to 277VAC covers the usual mains tolerances found across Europe, the Middle East and Asia, and it means a single part number can be stocked for markets where nominal voltage drifts.
The control interface accepts a 0 to 10V DC analog setpoint and a PWM duty signal, with tachometer output available for monitoring actual speed. This allows the fan to follow a pressure, temperature or CO2 transducer directly, or to be commanded by a building management system through an isolated signal. Because the controller limits current internally, soft start and locked-rotor protection are inherent, and the unit can be stopped and restarted on demand without inrush contactors.
Electrically, the fan is rated 230VAC nominal, 1.2 A maximum current, 155 W input power and 4000 RPM maximum speed, with airflow up to 727.5 CFM (1236.2 m3H) and static pressure up to 2.96 In.wg (740 Pa). Insulation is Class F, and the winding and electronics are protected against overtemperature and overcurrent. The motor is fitted with precision ball bearings lubricated for life and rated 40,000 hours L10 at 40 degrees C ambient; where ambient is lower, expected life extends considerably, and the bearings are not field-serviceable, so the fan is treated as a long-life sealed assembly.
The die-cast aluminum endcap carries the motor and provides the mounting datum, combining stiffness with good heat rejection from the controller. A 20AWG cable, 121 mm in free length, exits the housing for power and control connection. The FK3G190-2AGL-90 is CE marked and RoHS compliant, and it is manufactured under an ISO 9001 quality system with routine hipot, insulation resistance and balance checks on every unit. Typical installations include air-handling units, cleanroom return plenums, laboratory extract, dense filter banks and cabinet cooling, where the combination of 740 Pa pressure capability and steel impeller durability is the deciding factor.
| AC Plug Fan | ![]() |
|
| Type | FK3G190-2AGL-90 | |
| Model | BLDCEC92 | |
| Nominal Voltage | VAC | 230 |
| Voltage range | VAC | 184~277 |
| Current draw | A | 1.2±10% |
| Speed(RPM) | min-1 | 4000±5% |
| Power consumption | W | 155±10% |
| Sound Pressure Level | dB(A) | 73±5% |
| Max. Air Flow | CFM / m3 /H | 727.5/1236.2 |
| Max. Static Pressure | In.wg /Pa | 2.96/740 |
| Insulation class | ~ | Class B |
| Degree of protection | ~ | IP44 |
| Control Input | ~ | 0~10VDC / PWM |
| Signal Output | ~ | FG (Tach output ) |

Remarks:
Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized
Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel


Test condition:
Ⅰ.The test data is obtained under the specified environment conditions and installation mode
Ⅱ.Input Voltage---Operating voltage
Ⅲ.Temperature---Room temperature 25℃
Ⅴ.Humidity---65%RH
Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off
Ⅱ.Do not plug or unplug the fan lead plug when the fan is running
Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury
Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out
Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds
Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product
Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer
Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading
1. High Efficiency: The FK3G190-2AGL-90 delivers 1236.2 m3/h at 740 Pa while drawing only 155W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.
2. Industrial-Grade Impeller: The 190mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.
3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).
4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.
5. Easy Installation and Maintenance: Compact 190mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.
Q1:What kind of payments do you support?
A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping
Q2.Will you provide samples?
A2: Sample is available and can be delivered within 10days
Q3:How can I choose a more suitable model?
A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.
Q4:How can I place the order?
A4: Usually quote you within 24 hours after we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.
Q5:About transportation
A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive.
Q6:How long is the warranty period?
A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.