Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

FB3G190-48PL-91 DC Backward Curved Centrifugal Fan 190mm 48V 624 m3/h

FB3G190-48PL-91

Nominal Voltage VDC 48
Current draw A 1.8±10%
Speed(RPM) min-1  3300±5%
Power consumption W 86.4±10%
Max. Air Flow CFM / m3 /H 367.5/624.4
Max. Static Pressure In.wg /Pa 2.12/530

50pcs

Brand:
FANOVA
Spu:
FB3G190-48PL-91
  • Overview
  • Recommended Products
Brief Description

The FB3G190-48PL-91 is built around a 48VDC power architecture, the standard bus voltage found in telecom cabinet s, cellular base stations and battery-backed DC microgrids, so it drops straight onto an existing -48V rail without any AC conversion stage. Its second strength is frugal energy use: the complete fan assembly draws only 86.4 W at 3300 RPM while still moving up to 624.4 m3/h (367.5 CFM) and developing 530 Pa (2.12 In.wg) of static pressure, giving rack and enclosure designers strong thermal headroom inside a very small power budget. The impeller measures 190 mm across and is molded from glass-fiber reinforced propylene, a lightweight composite that keeps rotating mass low, resists many common chemical and moisture exposures, and avoids the cost premium of a metal wheel. Drive comes from a BLDCDC92 brushless DC motor with integrated commutation electronics, controlled through a 0 to 10V analog interface and PWM input, with tachometer feedback available for DCIM and BMS monitoring. Electrical ratings are 48VDC nominal (operating window 36 to 57VDC, written 136~57 in the data sheet), 1.8 A current draw, Class B insulation and electronic protection against locked-rotor, over-current and reverse polarity. Ball bearings rated for 70,000 hours at 40 degrees C let the unit run continuously in unattended cabinets, and acoustic output is held to 71 dB(A). A 500 mm lead in 20AWG wire simplifies field termination. Typical installations include 48V rectifier shelves, outdoor telecom enclosures, battery energy storage racks, EV charging modules, LED luminaire cooling and compact air-handling boxes. The fan carries CE and RoHS declarations and is produced under ISO 9001 quality management.

Product Specification

The FB3G190-48PL-91 belongs to the FB3G190 family of backward curved centrifugal fans and is configured for direct operation on nominal 48VDC supplies, with a usable input range of 36 to 57VDC as listed in the electrical table (136~57 in the source data). The single-inlet impeller is 190 mm in diameter and is injection molded from glass-fiber reinforced propylene. Between 32 and 36 backward-curved blades are arranged on the hub, each with an aerodynamically profiled leading edge that delays separation at the inlet and keeps the pressure curve stable as system resistance rises. The composite wheel weighs roughly one third of an equivalent sheet-steel impeller, which lowers starting torque, shortens spin-up time and reduces bearing load during speed transients; the material also tolerates humid, mildly alkaline and many solvent-bearing airstreams where painted steel would corrode. Each wheel is dynamically balanced to ISO 1940 grade G6.3 before assembly. The rotor is enclosed by a die-cast aluminum endcap and housing that stiffens the volute, damps structure-borne vibration and provides a stable mounting face for horizontal or vertical installation. The BLDCDC92 motor is a three-phase brushless DC machine with surface-mounted permanent magnets and integrated electronic commutation; Hall sensors and a sensorless back-EMF algorithm run in parallel so the drive recovers cleanly from load steps and from brief supply dips. Speed is set by a 0 to 10V analog control line or by a 25 kHz PWM duty-cycle input, and a separate frequency output delivers a two-pulse-per-revolution tachometer signal for DCIM, SNMP cards and BMS platforms. At 3300 RPM the fan delivers a maximum free-air flow of 624.4 m3/h (367.5 CFM) and a maximum static pressure of 530 Pa (2.12 In.wg), with peak efficiency in the mid-flow region. Electrical input at rated speed is 86.4 W from 1.8 A at 48VDC, and the internal electronics include soft-start current limiting, locked-rotor shutdown with automatic restart, over-current and reverse-polarity protection. Motor insulation is Class B, and the winding is vacuum-impregnated to resist vibration. The shaft runs in two pre-lubricated ball bearings rated for 70,000 hours L10 life at 40 degrees C ambient. Acoustic emission is 71 dB(A) at one meter in free field; the backward-curved blade geometry and the rigid aluminum housing together suppress the discrete blade-passage tone. The unit is supplied with a 500 mm flying lead in 20AWG wire, and the supply and control conductors are color-coded for straightforward termination. Every fan is hipot tested, run-in and functionally checked before packing, and production follows ISO 9001 procedures with CE and RoHS declarations issued against the model. Typical deployments include 48V telecom rectifier shelves, outdoor base-station cabinets, battery energy storage modules, EV charger power stacks and compact air-handling units where a 190 mm wheel fits the available duct envelope.

Nominal Date
DC Backward Curved Centrifugal Fan image.png
Type FB3G190-48PL-91
Model BLDCDC92

 

Nominal Voltage VDC 48
Voltage range VDC 136~57
Current draw A 1.8±10%
Speed(RPM) min-1  3300±5%
Power consumption W 86.4±10%
Sound Pressure Level dB(A) 71±5%
Max. Air Flow CFM / m3 /H 367.5/624.4
Max. Static Pressure In.wg /Pa 2.12/530
Insulation class ~ Class B
Degree of protection ~ IP44
Control Input ~ 0~10VDC / PWM
Signal Output ~ FG (Tach output )
Connection diagram
image.png

Remarks:

Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized

Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel

Product drawing
image.png
Aerodynamic Performance Charts
image.png

Test condition:

Ⅰ.The test data is obtained under the specified environment conditions and installation mode

Ⅱ.Input Voltage---Operating voltage

Ⅲ.Temperature---Room temperature 25℃

Ⅴ.Humidity---65%RH

Safety Requirements

Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off

Ⅱ.Do not plug or unplug the fan lead plug when the fan is running

Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury

Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out

Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds

Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product

Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer

Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading

Advantages:

1. High Efficiency: The FB3G190-48PL-91 delivers 624.4 m3/h at 530 Pa while drawing only 86.4W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.

2. Industrial-Grade Impeller: The 190mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.

3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).

4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.

5. Easy Installation and Maintenance: Compact 190mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.

FAQ

Q1:What kind of payments do you support?

A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping

Q2.Will you provide samples?

A2: Sample is available and can be delivered within 10days

Q3:How can I choose a more suitable model?

A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.

Q4:How can I place the order?

A4:  Usually quote you within 24 hours  after  we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.

Q5:About transportation

A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive. 

Q6:How long is the warranty period?

A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000