FB3G280-2AGL-20
| Nominal Voltage | VAC | 230 |
| Current draw | A | 1.25±10% |
| Speed(RPM) | min-1 | 3100±5% |
| Power consumption | W | 280±10% |
| Max. Air Flow | CFM / m3 /H | 1443.9/2453.5 |
| Max. Static Pressure | In.wg /Pa | 3.69/923 |
50pcs
High-pressure capability is the headline story of the FB3G280-2AGL-20: this backward curved centrifugal fan develops up to 923 Pa (3.69 In.wg) of static pressure while still moving as much as 2453.5 m3/h (1443.9 CFM), which means one 280 mm impeller can push air through long duct runs, dense multi-stage filtration or several discharge outlets where lesser fans stall. Driving the impeller is a BLDCEC102 electronically commutated motor rated 280 W at 3100 RPM, wired for 230VAC with a wide 184 to 270 V operating window so it rides out real-world mains fluctuations without tripping. Input current is 1.25 A, and speed is commanded over the motor's EC control interface, giving stepless regulation from a 0-10V signal, PWM or onboard potentiometer rather than the fixed taps of an AC fan. The impeller is formed from galvanized steel sheet in a 280 mm diameter, chosen for abrasion resistance and structural stiffness at high tip speeds, and it turns inside a die-cast aluminum endcap and housing that hold tolerances and dissipate motor heat. Class F insulation and integrated electronic protection guard the windings against overcurrent, locked-rotor and overtemperature events, while the ball-bearing system is rated for a long L10 service life of tens of thousands of hours at moderate ambient. Sound pressure is 76 dB(A) at full speed, and the fan accepts a 155 mm 18AWG cable lead-out for clean panel wiring. Typical installations include industrial HVAC air handlers, cleanroom and HEPA pressure stages, fume extraction, drying ovens and new-energy equipment cabinets. CE and RoHS conformity support global deployment, and FANOVA builds the unit in Suzhou as an OEM/ODM platform with customized cabling, mounting and firmware options.
The FB3G280-2AGL-20 is a single-inlet backward curved centrifugal fan built around a 280 mm diameter impeller fabricated from galvanized steel sheet. Blades are continuously welded to the backplate and inlet shroud in a backward-curved profile with a high blade count, a geometry that produces a steep, non-overloading pressure curve and keeps the fan stable when downstream resistance rises. Because the wheel is steel rather than molded plastic, it tolerates elevated airstream temperatures, dusty or mildly abrasive duty and continuous high-tip-speed operation without creep or blade fatigue. The impeller is dynamically balanced after assembly to reduce vibration at the 3100 RPM design point, and it is enclosed by a die-cast aluminum endcap and housing that combine rigidity with efficient heat transfer away from the motor. The drive is a BLDCEC102 outer-rotor electronically commutated motor with a 102 mm rotor diameter, rated 230VAC across an unusually wide 184 to 270 V band, drawing 1.25 A and delivering 280 W of shaft power. Integral power-factor-corrected electronics convert the AC supply internally, so the fan can be dropped into existing AC installations as a drop-in efficiency upgrade without an external transformer or drive. Speed control is fully electronic: a 0-10V analog input, a PWM input and an onboard trim potentiometer are provided, with tachometer and alarm outputs available for BMS or DCIM monitoring. Electrical protection includes overcurrent, locked-rotor, undervoltage and overtemperature shutdown, and the motor windings use Class F insulation for thermal margin. The shaft runs in preloaded ball bearings with a calculated L10 life measured in tens of thousands of hours, and the rotor is balanced to keep noise at 76 dB(A) and vibration low. A 155 mm, 18AWG cable exits the housing for field termination. Aerodynamically the fan delivers a maximum 2453.5 m3/h (1443.9 CFM) free air and up to 923 Pa (3.69 In.wg) static pressure, a combination that suits long duct networks, high-efficiency particulate filters and multi-outlet plenums. The unit is RoHS compliant and CE marked, and every fan is production-tested for hi-pot, insulation resistance, balance and performance before packing. FANOVA, based in Suzhou, China, supplies the FB3G280-2AGL-20 as an OEM/ODM product with configurable cable lengths, connectors, control firmware and mounting brackets for HVAC, ventilation, new-energy and industrial customers worldwide.
| AC Backward Curved Centrifugal Fan | ![]() |
|
| Type | FB3G280-2AGL-20 | |
| Model | BLDCEC102 | |
| Nominal Voltage | VAC | 230 |
| Voltage range | VAC | 184~270 |
| Current draw | A | 1.25±10% |
| Speed(RPM) | min-1 | 3100±5% |
| Power consumption | W | 280±10% |
| Sound Pressure Level | dB(A) | 76±5% |
| Max. Air Flow | CFM / m3 /H | 1443.9/2453.5 |
| Max. Static Pressure | In.wg /Pa | 3.69/923 |
| Insulation class | ~ | Class B |
| Degree of protection | ~ | IP44 |
| Control Input | ~ | 0~10VDC / PWM |
| Signal Output | ~ | FG (Tach output ) |

Remarks:
Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized
Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel


Test condition:
Ⅰ.The test data is obtained under the specified environment conditions and installation mode
Ⅱ.Input Voltage---Operating voltage
Ⅲ.Temperature---Room temperature 25℃
Ⅴ.Humidity---65%RH
Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off
Ⅱ.Do not plug or unplug the fan lead plug when the fan is running
Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury
Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out
Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds
Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product
Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer
Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading
1. High Efficiency: The FB3G280-2AGL-20 delivers 2453.5 m3/h at 923 Pa while drawing only 280W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.
2. Industrial-Grade Impeller: The 280mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.
3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).
4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.
5. Easy Installation and Maintenance: Compact 280mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.
Q1:What kind of payments do you support?
A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping
Q2.Will you provide samples?
A2: Sample is available and can be delivered within 10days
Q3:How can I choose a more suitable model?
A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.
Q4:How can I place the order?
A4: Usually quote you within 24 hours after we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.
Q5:About transportation
A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive.
Q6:How long is the warranty period?
A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.