FK3G175-2ALH-7A
| Nominal Voltage | VAC | 230 |
| Current draw | A | 0.3±10% |
| Speed(RPM) | min-1 | 2850±5% |
| Power consumption | W | 35±10% |
| Max. Air Flow | CFM / m3 /H | 320.3/544.3 |
| Max. Static Pressure | In.wg /Pa | 1.3/325 |
50pcs
The FK3G175-2ALH-7A is a whisper-quiet plug fan built around three engineering signatures: acoustics below the level of ordinary conversation, full-range 230VAC EC operation, and a power draw of only 35 W. Running at 2850 RPM, this 175 mm backward-curved centrifugal fan moves up to 544.3 m3/h (320.3 CFM) against a maximum static pressure of 325 Pa (1.3 In.wg), yet its sound pressure is held to 59.4 dB(A), which makes it a natural fit for meeting rooms, clinics, laboratory benches and office ventilation where fan noise is unacceptable. The single-phase 230VAC supply accepts anything from 184 to 277 V, so one SKU covers nominal 220 V, 230 V and 240 V grids without a step-down transformer or rewiring. Inside, a BLDC EC72 external-rotor motor with integrated electronics draws just 0.3 A and delivers electronic commutation instead of brush wear, while the impeller is molded from propylene reinforced with glass fiber, giving a light rotating mass that reaches speed quickly and resists many chemical vapors. Control is handled through the onboard EC interface, allowing 0-10 V or PWM speed setting and tach feedback so airflow can be trimmed to the exact duty point rather than fixed by a transformer tap. Insulation is Class B and the electronics are protected against locked-rotor and over-temperature conditions, and the motor is rated for a long L10 bearing life suitable for continuous duty. Typical installations include air-handling units, fan coils, cleanroom recirculation, telecom cabinets and light commercial exhaust, and the fan carries CE and RoHS compliance consistent with FANOVA's OEM/ODM quality system. The FK3G175-2ALH-7A is the model to specify when the brief says quiet first, efficient second and simple to install third.
The FK3G175-2ALH-7A is a 175 mm diameter plug fan from FANOVA's backward-curved centrifugal range, supplied as a ready-to-mount assembly with a die-cast aluminum endcap and a 72 mm rotor. The impeller is injection molded in glass-fiber reinforced propylene, a material chosen because its low density keeps rotating inertia small, its molded blade geometry can be held to tight tolerances for low turbulence and low noise, and its chemical resistance suits humid or mildly corrosive air streams. The backward-curved blade form produces a steep pressure characteristic, so the fan holds its working point when filters load or duct resistance rises, and the 325 Pa maximum static pressure is achieved at a flow well above the free-delivery condition, letting the 544.3 m3/h peak airflow and the pressure ceiling be balanced against each other for each installation. Air is drawn axially and discharged radially through the scroll, which is why the unit slots directly into an AHU panel or a plenum chamber without a separate housing.\n\nAt the heart of the fan is the BLDC EC72 external-rotor electronically commutated motor, rated 35 W at 2850 RPM and drawing 0.3 A from a single-phase 230VAC supply that tolerates 184 to 277 V. The integrated inverter rectifies and re-drives the mains supply, so speed is independent of line frequency and the same fan works on 50 Hz and 60 Hz grids. Speed can be set by a 0-10 VDC analog signal, by a PWM input, or by the internal potentiometer, and a tachometer output reports actual RPM to a BMS or controller; a floating alarm contact is available on request. Because the motor is electronically commutated, there are no brushes and no capacitor-run winding, and efficiency stays high across the whole speed band rather than peaking at one operating point. Electrical connection is by a 500 mm flying lead of 20AWG cable, with separate conductors for supply, control and tach, allowing the installer to commission the fan from a terminal box or a wall-mounted controller.\n\nMechanically the fan is built for long unattended service. The rotor runs in sealed, pre-lubricated ball bearings selected for an L10 life that comfortably exceeds the usual air-handling duty cycle, and the external-rotor layout places the bearings close to the impeller to minimize overhung load. The die-cast aluminum endcap dissipates motor heat and stiffens the mounting face, and the whole assembly is balanced after moulding to keep vibration low at 2850 RPM, which is what holds the sound level down to 59.4 dB(A). Insulation is Class B, the electronics include locked-rotor and over-temperature protection, and the fan is designed for ambient temperatures typical of HVAC plant rooms. CE and RoHS declarations are issued with each shipment, and production follows FANOVA's ISO-based quality system with routine performance and hipot testing on every unit. As an OEM/ODM supplier, FANOVA can adapt cable length, connector type, control protocol and mounting details for volume programs, making the FK3G175-2ALH-7A equally suitable as a catalog item or as a custom-built fan for a specific air-handling platform.
| AC Plug Fan | ![]() |
|
| Type | FK3G175-2ALH-7A | |
| Model | BLDCEC72 | |
| Nominal Voltage | VAC | 230 |
| Voltage range | VAC | 184~277 |
| Current draw | A | 0.3±10% |
| Speed(RPM) | min-1 | 2850±5% |
| Power consumption | W | 35±10% |
| Sound Pressure Level | dB(A) | 59.4±5% |
| Max. Air Flow | CFM / m3 /H | 320.3/544.3 |
| Max. Static Pressure | In.wg /Pa | 1.3/325 |
| Insulation class | ~ | Class B |
| Degree of protection | ~ | IP44 |
| Control Input | ~ | 0~10VDC / PWM |
| Signal Output | ~ | FG (Tach output ) |

Remarks:
Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized
Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel


Test condition:
Ⅰ.The test data is obtained under the specified environment conditions and installation mode
Ⅱ.Input Voltage---Operating voltage
Ⅲ.Temperature---Room temperature 25℃
Ⅴ.Humidity---65%RH
Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off
Ⅱ.Do not plug or unplug the fan lead plug when the fan is running
Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury
Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out
Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds
Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product
Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer
Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading
1. High Efficiency: The FK3G175-2ALH-7A delivers 544.3 m3/h at 325 Pa while drawing only 35W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.
2. Industrial-Grade Impeller: The 175mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.
3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).
4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.
5. Easy Installation and Maintenance: Compact 175mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.
Q1:What kind of payments do you support?
A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping
Q2.Will you provide samples?
A2: Sample is available and can be delivered within 10days
Q3:How can I choose a more suitable model?
A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.
Q4:How can I place the order?
A4: Usually quote you within 24 hours after we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.
Q5:About transportation
A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive.
Q6:How long is the warranty period?
A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.