Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

FD3G133-2AGL-70 EC Dual Inlet Centrifugal Blower 133mm 230V 857 m3/h

FD3G133-2AGL-70

Nominal Voltage VAC 230
Current draw A 0.75±10%
Speed(RPM) min-1  1500±5%
Power consumption W 105±10%
Max. Air Flow CFM / m3 /H 524.9/857.2
Max. Static Pressure In.wg /Pa 0.78/175

50pcs

Brand:
FANOVA
Spu:
FD3G133-2AGL-70
  • Overview
  • Recommended Products
Brief Description

When a 133 mm dual-inlet blower is specified at 64 dB(A), the design target is quiet operation, not merely low noise on paper. The FD3G133-2AGL-70 meets that target by pairing a 72 mm BLDCEC72 rotor with a galvanized steel dual-inlet impeller, delivering 524.9 CFM (857.2 m3/h) at 0.78 in.wg (175 Pa) while drawing only 105 W from a 230 VAC supply. Rather than treating steel as a durability-only choice, this model uses the stiffness and dimensional stability of galvanized sheet to hold tight blade tolerances at 1500 RPM, which keeps the blade-pass tone controlled and the overall sound signature below conversational level. The 230 VAC input accepts 184 to 277 VAC, so the blower can be commissioned directly on European, Asian or North American 230 V single-phase circuits without a step-down transformer, and the EC motor maintains speed and airflow as line voltage fluctuates. Control is via a 0-10 VDC or PWM interface, with tach output available for verification; the integrated electronics remove the need for external VFDs, contactors or motor protection relays. Electrical safety is assured by Class F insulation, an internal thermal cutoff and an ingress-protected die-cast aluminum endcap that also acts as the heat sink for the drive electronics. The 20AWG, 176 mm cable provides a short, serviceable lead for panel wiring, and the dual ball-bearing system is rated for 40,000 hours at 40 degrees C, giving maintenance intervals that align with air-handling unit service schedules. Typical applications include medical and laboratory exhaust, office ventilation, cleanroom recirculation, fan-coil units and air purifiers where sound pressure at the occupied zone is a design constraint. The blower is CE and RoHS compliant, and production is supported by FANOVA's Suzhou manufacturing and test facility with airflow, power and noise verification on every unit.

Product Specification

The FD3G133-2AGL-70 is a dual-inlet centrifugal blower built around a 133 mm diameter impeller formed from galvanized steel sheet. Each impeller uses a forward-curved blade set with a defined blade count selected to balance pressure development against tonal noise; the galvanized coating provides corrosion resistance in humid air streams while the steel substrate maintains blade geometry under centrifugal load at 1500 RPM. The two impeller halves are mounted on a common shaft and enclosed by a die-cast aluminum endcap and housing that combine structural rigidity with effective heat dissipation for the motor drive. The rotor diameter is 72 mm, and the BLDCEC72 motor is an electronically commutated permanent-magnet design with integrated three-phase drive electronics. Speed control is through a 0-10 VDC analog input or a PWM signal, with a tachometer output for speed verification and fault monitoring; the control interface is isolated from the mains and accepts logic-level signals from a building management system or dedicated controller. Electrical ratings are 230 VAC nominal with an operating range of 184 to 277 VAC, 0.75 A current draw and 105 W input power at maximum speed. The motor is Class F insulated and protected by an internal thermal cutoff, and the drive electronics include overcurrent, overvoltage and locked-rotor protection. The blower is supplied with a 20AWG cable, 176 mm in length, for connection to a terminal block or panel-mounted controller. The bearing system uses dual pre-lubricated ball bearings rated for 40,000 hours at 40 degrees C ambient, with the shaft and bearing housing machined to maintain rotor alignment and minimize vibration transmitted to the housing. Aerodynamic performance at maximum speed is 524.9 CFM (857.2 m3/h) at a maximum static pressure of 0.78 in.wg (175 Pa), with a sound pressure level of 64 dB(A) measured at the standard test position. The unit is CE and RoHS compliant and is manufactured under FANOVA's quality system, with each blower subjected to performance and safety testing before shipment.

Nominal Date
AC Dual Inlet Centrifugal Blower image.png
Type FD3G133-2AGL-70
Model BLDCEC72

 

Nominal Voltage VAC 230
Voltage range VAC 184~277
Current draw A 0.75±10%
Speed(RPM) min-1  1500±5%
Power consumption W 105±10%
Sound Pressure Level dB(A) 64±5%
Max. Air Flow CFM / m3 /H 524.9/857.2
Max. Static Pressure In.wg /Pa 0.78/175
Insulation class ~ Class B
Degree of protection ~ IP44
Control Input ~ 0~10VDC / PWM
Signal Output ~ FG (Tach output )
Connection diagram
image.png

Remarks:

Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized

Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel

Product drawing
image.png
Aerodynamic Performance Charts
image.png

Test condition:

Ⅰ.The test data is obtained under the specified environment conditions and installation mode

Ⅱ.Input Voltage---Operating voltage

Ⅲ.Temperature---Room temperature 25℃

Ⅴ.Humidity---65%RH

Safety Requirements

Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off

Ⅱ.Do not plug or unplug the fan lead plug when the fan is running

Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury

Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out

Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds

Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product

Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer

Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading

Advantages:

1. High Efficiency: The FD3G133-2AGL-70 delivers 857.2 m3/h at 175 Pa while drawing only 105W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.

2. Industrial-Grade Impeller: The 133mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.

3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).

4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.

5. Easy Installation and Maintenance: Compact 133mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.

FAQ

Q1:What kind of payments do you support?

A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping

Q2.Will you provide samples?

A2: Sample is available and can be delivered within 10days

Q3:How can I choose a more suitable model?

A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.

Q4:How can I place the order?

A4:  Usually quote you within 24 hours  after  we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.

Q5:About transportation

A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive. 

Q6:How long is the warranty period?

A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000