FD3G146-24GL-90
| Nominal Voltage | VDC | 24 |
| Current draw | A | 8.4±10% |
| Speed(RPM) | min-1 | 1700±5% |
| Power consumption | W | 201.6±10% |
| Max. Air Flow | CFM / m3 /H | 890.9/1513.9 |
| Max. Static Pressure | In.wg /Pa | 1.31/328 |
50pcs
When a single compact blower must move more than 1500 m3/h of air in a 24 VDC system, the FD3G146-24GL-90 is the answer: a dual inlet centrifugal blower that replaces multiple smaller fans while keeping wiring simple and safe. This 201.6 W, 1700 RPM unit delivers 890.9 CFM (1513.9 m3/h) at free air and 1.31 in.wg (328 Pa) of static pressure, enough to push through dense filter banks or long duct runs. The heart of the blower is a BLDCDC92 brushless DC motor, driven by an integrated EC controller that accepts 16 to 28 VDC and draws 8.4 A at nominal 24 V. Speed is set by a 0-10 V analog signal or PWM input, so the same blower can be ramped for night setback or constant-pressure control. The 146 mm impeller is fabricated from galvanized steel sheet for abrasion resistance and long service in dusty or high-temperature airstreams, while the die-cast aluminum endcap and housing hold tolerances and dissipate motor heat. Insulation is Class F with Class B rise, and the motor carries locked-rotor, over-voltage and over-temperature protection. Dual ball bearings rated L10 at 70,000 hours at 40 C keep maintenance intervals long. Typical installations include telecom shelters, energy-storage cabinets, commercial air handling units, laboratory exhaust, and off-grid solar ventilation. The unit is CE and RoHS compliant and produced under ISO 9001. FANOVA offers OEM/ODM customization of cable length, connector, speed curve and labeling for qualified projects.
The FD3G146-24GL-90 is a dual inlet centrifugal blower built around a 146 mm diameter impeller, a size chosen to balance flow capacity against cabinet footprint. Each impeller is formed from galvanized steel sheet, with blades stamped, folded and riveted to a steel backplate and inlet ring. The galvanized coating provides sacrificial corrosion protection and resists the abrasive wear that often shortens the life of plastic wheels in particulate-laden airstreams. The wheel is dynamically balanced after assembly to ISO 1940 G6.3, a step that keeps vibration low at the 1700 RPM operating point and protects the motor bearings. The blower housing is a die-cast aluminum volute with machined mating faces; aluminum was selected over stamped steel for dimensional stability, better heat rejection from the motor and lower tooling cost at this volume. Two inlet throats feed the single wheel from both sides, producing the characteristic dual inlet flow pattern that raises pressure and flow without increasing rotational speed.
Air performance is rated at 890.9 CFM, or 1513.9 m3/h, at free delivery, with a maximum static pressure of 1.31 in.wg, or 328 Pa. The flow-pressure curve is relatively flat through the mid-range, which suits systems with variable filter loading. Acoustic output is 72 dB(A) measured at one meter in free field; the dual inlet layout distributes the sound across two inlet paths and reduces the tonal peak compared with single inlet designs of similar output. The motor is a BLDCDC92 brushless DC machine with an integrated electronic commutator and driver board mounted in the airstream for cooling. Electrical input is 24 VDC nominal, with an operating window from 16 to 28 VDC, and current draw of 8.4 A at full speed, giving 201.6 W of input power. The controller accepts a 0-10 VDC analog setpoint or a 25 kHz PWM duty signal on the control lead, and provides an open-collector tachometer output for speed feedback to a building management system. Soft-start limits inrush current, and the drive includes locked-rotor, over-voltage, under-voltage and over-temperature protection with automatic restart.
Electrical connection is made through a 209 mm flying lead of 20 AWG cable, color-coded for power, ground, control and tachometer. The cable exits the aluminum housing through a sealed grommet. Motor insulation is Class F, with Class B temperature rise at rated load, allowing operation in ambient temperatures up to 40 C without derating. The rotor shaft runs in two pre-lubricated ball bearings selected for an L10 rating of 70,000 hours at 40 C; the bearing bores are machined into the die-cast endcap to maintain alignment under belt-free direct drive. The complete blower weighs approximately 3.2 kg and is mounted via four tapped bosses on the housing feet, with optional resilient mounts to isolate residual vibration. The unit is CE marked and RoHS compliant, is manufactured in an ISO 9001 certified facility, and is 100 percent run-tested for speed, current and pressure before packing. FANOVA can supply application-specific variants with alternate cable lengths, connectors, speed profiles or impeller coatings under its OEM/ODM program.
| DC Dual Inlet Centrifugal Blower | ![]() |
|
| Type | FD3G146-24GL-90 | |
| Model | BLDCDC92 | |
| Nominal Voltage | VDC | 24 |
| Voltage range | VDC | 16~28 |
| Current draw | A | 8.4±10% |
| Speed(RPM) | min-1 | 1700±5% |
| Power consumption | W | 201.6±10% |
| Sound Pressure Level | dB(A) | 72±5% |
| Max. Air Flow | CFM / m3 /H | 890.9/1513.9 |
| Max. Static Pressure | In.wg /Pa | 1.31/328 |
| Insulation class | ~ | Class B |
| Degree of protection | ~ | IP44 |
| Control Input | ~ | 0~10VDC / PWM |
| Signal Output | ~ | FG (Tach output ) |

Remarks:
Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized
Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel


Test condition:
Ⅰ.The test data is obtained under the specified environment conditions and installation mode
Ⅱ.Input Voltage---Operating voltage
Ⅲ.Temperature---Room temperature 25℃
Ⅴ.Humidity---65%RH
Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off
Ⅱ.Do not plug or unplug the fan lead plug when the fan is running
Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury
Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out
Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds
Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product
Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer
Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading
1. High Efficiency: The FD3G146-24GL-90 delivers 1513.9 m3/h at 328 Pa while drawing only 201.6W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.
2. Industrial-Grade Impeller: The 146mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.
3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).
4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.
5. Easy Installation and Maintenance: Compact 146mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.
Q1:What kind of payments do you support?
A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping
Q2.Will you provide samples?
A2: Sample is available and can be delivered within 10days
Q3:How can I choose a more suitable model?
A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.
Q4:How can I place the order?
A4: Usually quote you within 24 hours after we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.
Q5:About transportation
A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive.
Q6:How long is the warranty period?
A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.