FB3G280-2AGY-20
| Nominal Voltage | VAC | 230 |
| Current draw | A | 1.8±10% |
| Speed(RPM) | min-1 | 2780±5% |
| Power consumption | W | 410±10% |
| Max. Air Flow | CFM / m3 /H | 1731.96/2943 |
| Max. Static Pressure | In.wg /Pa | 3.36/840 |
50pcs
When one air mover has to carry the entire airflow budget of a cabinet, duct run or process line, the FB3G280-2AGY-20 is built for that job: a 280 mm backward curved impeller in galvanized steel delivers 2943 m3H (1732 CFM) at free air and still pushes 840 Pa (3.36 In.wg) of static pressure, so a single fan can retire the pair or trio of smaller units it replaces. Behind that output sits a BLDCEC102 electronically commutated motor rated 410 W at 2780 RPM on 230 VAC, drawing 1.8 A across a wide 184 to 270 VAC window so it rides out grid sag and surge without a stabilizer. Because the motor is EC, speed is trimmed by a 0-10 VDC or PWM control signal rather than a transformer or variac, giving stepless turndown and soft-start inrush well below the 1.8 A running figure. The die-cast aluminum endcap and housing hold rotor alignment under continuous duty, and the assembly is Class F insulated with Class B rise limits, tested to 1500 VAC dielectric strength and protected against locked rotor and over-temperature. Dual ball bearings rated L10 at 70,000 hours at 40 degC ambient carry the radial and axial loads of a 280 mm steel wheel. At 83.6 dB(A) the acoustic signature reflects the high-output duty point, and the fan is normally mounted on anti-vibration isolators inside an acoustic enclosure. Typical installations include cleanroom make-up air, HEPA pre-filtration banks, fume hood exhaust, drying ovens, telecom shelters, EV charging cabinets and general industrial supply or extract ductwork. CE and RoHS conformity, an IP54-rated motor enclosure and a 500 mm 18AWG flying lead complete the package for OEM integration.
The impeller of the FB3G280-2AGY-20 is a 280 mm diameter backward curved centrifugal wheel fabricated from galvanized steel sheet, with the corrosion-resistant zinc coating left intact on both faces so the blade passages tolerate humid, mildly acidic and dusty airstreams without a secondary finish. Blades are formed to a backward inclined profile and riveted or clinched to the backplate and inlet shroud at controlled pitch, a construction that self-limits absorbed power as resistance rises and keeps the motor out of overload at the top of the duct system curve. The wheel is dynamically balanced after assembly to ISO 1940 grade G6.3, which controls the once-per-revolution excitation that would otherwise transmit through the housing into cabinet panels at 2780 RPM. Air enters axially through the inlet ring, turns through the blade passages and leaves radially into the die-cast aluminum scroll, whose machined surfaces and tight cut-off clearance hold the pressure characteristic flat well past the free-air point. The motor is a BLDCEC102 three-phase electronically commutated design with a permanent magnet rotor measuring 102 mm in diameter, driven by an integrated inverter that rectifies the 230 VAC mains, regulates the DC link and commutates the stator windings in response to rotor position feedback. The 184 to 270 VAC input range means the fan can be specified on nominal 230 V systems in Europe, the Middle East, Asia and Australia without a step-down transformer, and it will continue to run through brownouts that would stall an AC induction equivalent. Rated input is 410 W at 1.8 A and 2780 RPM, with power factor correction bringing the displacement factor near unity so supply cabling and breaker sizing are governed by real rather than apparent current. Speed control is exercised through a 0-10 VDC analog input or a PWM duty signal referenced to the control common, both isolated from mains, with a tachometer or frequency output available for verification of actual RPM; the electronics include soft-start ramping, locked-rotor shutdown, over-temperature foldback and reverse-polarity protection on the control lines. Electrical connection is made through a 500 mm flying lead of 18AWG conductors, with separate cores for mains, control and tach, and the motor enclosure is rated IP54 against dust ingress and water splash. The stator uses Class F insulation with Class B temperature rise under rated load, and the winding is hipot tested to 1500 VAC for one minute before assembly. Mechanical support comes from two pre-lubricated double-shielded ball bearings selected for an L10 rating life of 70,000 hours at 40 degC ambient, mounted in the die-cast aluminum endcap that also serves as the motor heat sink and maintains rotor-to-stator concentricity through thermal cycling. The die-cast aluminum housing combines rigidity with mass damping, and the fan is intended for mounting on rubber or spring isolators with the discharge oriented to suit the duct layout. The completed unit is checked for airflow, static pressure, power, current and noise on the production line, and the series carries CE marking and RoHS compliance for sale into the European Economic Area; custom cable lengths, connector terminations, alternative control voltage ranges and IP55 sealing upgrades are available on request under the FANOVA OEM/ODM program.
| AC Backward Curved Centrifugal Fan | ![]() |
|
| Type | FB3G280-2AGY-20 | |
| Model | BLDCEC102 | |
| Nominal Voltage | VAC | 230 |
| Voltage range | VAC | 184~270 |
| Current draw | A | 1.8±10% |
| Speed(RPM) | min-1 | 2780±5% |
| Power consumption | W | 410±10% |
| Sound Pressure Level | dB(A) | 83.6±5% |
| Max. Air Flow | CFM / m3 /H | 1731.96/2943 |
| Max. Static Pressure | In.wg /Pa | 3.36/840 |
| Insulation class | ~ | Class B |
| Degree of protection | ~ | IP44 |
| Control Input | ~ | 0~10VDC / PWM |
| Signal Output | ~ | FG (Tach output ) |

Remarks:
Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized
Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel


Test condition:
Ⅰ.The test data is obtained under the specified environment conditions and installation mode
Ⅱ.Input Voltage---Operating voltage
Ⅲ.Temperature---Room temperature 25℃
Ⅴ.Humidity---65%RH
Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off
Ⅱ.Do not plug or unplug the fan lead plug when the fan is running
Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury
Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out
Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds
Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product
Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer
Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading
1. High Efficiency: The FB3G280-2AGY-20 delivers 2943 m3/h at 840 Pa while drawing only 410W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.
2. Industrial-Grade Impeller: The 280mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.
3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).
4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.
5. Easy Installation and Maintenance: Compact 280mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.
Q1:What kind of payments do you support?
A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping
Q2.Will you provide samples?
A2: Sample is available and can be delivered within 10days
Q3:How can I choose a more suitable model?
A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.
Q4:How can I place the order?
A4: Usually quote you within 24 hours after we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.
Q5:About transportation
A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive.
Q6:How long is the warranty period?
A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.