Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

FB3G150-2APL-70 EC Backward Curved Centrifugal Fan 150mm 230V 455 m3/h

FB3G150-2APL-70

Nominal Voltage VAC 230
Current draw A 0.3±10%
Speed(RPM) min-1  3550±5%
Power consumption W 35±10%
Max. Air Flow CFM / m3 /H 268/455.4
Max. Static Pressure In.wg /Pa 1.42/355

50pcs

Brand:
FANOVA
Spu:
FB3G150-2APL-70
  • Overview
  • Recommended Products
Brief Description

Quiet enough to hold a conversation beside, the FB3G150-2APL-70 is a 150 mm backward curved centrifugal fan that measures just 63 dB(A) at full speed while still moving 268 CFM (455.4 m3/h). Its EC motor draws only 35 W at 3550 RPM on a 230VAC supply, and because the EC72 electronics accept anything from 184 to 277 V, the same fan can be dropped into 208 V, 240 V or 277 V panels without a transformer or a wiring change. The impeller is molded from glass-fiber reinforced propylene, so the blades are light, chemically resistant and dimensionally stable, while the die-cast aluminum endcap holds the 72 mm rotor rigidly on axis to keep vibration and tonal noise low. Control is fully electronic: a 0-10 VDC or PWM signal sets speed continuously from a standstill to maximum, and the integrated commutation removes the brush wear and sparking of a DC machine. Insulation is Class B with an electronic cut-out against locked-rotor and over-temperature faults, and the dual ball bearings are rated for 40,000 hours at 40 degrees C, which suits continuous duty in air handlers, lab fume hoods, medical cabinets, cleanroom FFU stacks and telecom enclosures. The 20AWG, 500 mm flying lead simplifies retrofit, and the fan carries CE and RoHS compliance as standard. Where noise budgets and energy bills both matter, this model replaces a larger AC blower with less airflow, higher consumption and more acoustic treatment.

Product Specification

The FB3G150-2APL-70 is built around a 150 mm diameter backward curved impeller injection-molded in glass-fiber reinforced propylene. The backward-curved blade geometry is self-cleaning in the aerodynamic sense: the blade passages widen toward the outlet so particles and light dust do not lodge on the trailing edges, and the non-overloading power curve means the motor cannot be overloaded by a rising system resistance. The hub is keyed and balanced as an assembly, with residual unbalance held to ISO 1940 G6.3, which keeps the 3550 RPM running point free of the low-frequency beat that often forces designers to add mass to a sheet-metal housing. The die-cast aluminum endcap doubles as the motor heat sink and as the structural bridge between the impeller and the mounting flange, giving the 72 mm rotor a stiff, concentric seat that holds air-gap tolerance over the service life. The EC72 motor is a three-phase brushless permanent-magnet design with integrated commutation electronics, sinusoidal drive and power factor correction, drawing 0.3 A at 230 VAC and 35 W at the rated point while accepting 184 to 277 VAC, 50/60 Hz. Speed is commanded through a 0-10 VDC analog input or a 25 kHz PWM input, with tachometer and alarm outputs available on the control lead; the control circuit is isolated from the mains, and the fan can be run from a building management system, a thermostat, a differential-pressure sensor or a manual potentiometer. The electronics include soft start, locked-rotor protection, over-temperature shutdown and reverse-polarity protection on the control side. Insulation is Class B, the winding is vacuum-impregnated, and the fan is designed for dielectric strength of 1500 VAC for one minute between winding and frame. The shaft runs in two pre-lubricated dual-shielded ball bearings rated L10 at 40,000 hours at 40 degrees C ambient, mounted in an elastomer-isolated bearing tube to suppress structure-borne noise; the impeller is retained by a stainless steel circlip and the shaft is ground to h6 tolerance for a press-fit inner race. Electrical connection is a 500 mm flying lead in 20AWG, with clearly marked live, neutral, earth, control and tachometer conductors, and the lead exits the endcap through a strain-relieved grommet. The fan mounts on four M4 holes on the discharge flange, can be installed in any orientation, and is rated for operation from -20 to +60 degrees C. Acoustic output is 63 dB(A) at one meter at the free-delivery point, falling as the operating point moves up the curve toward higher static pressure. Aerodynamic performance peaks at 268 CFM (455.4 m3/h) free delivery and 1.42 in.wg (355 Pa) shut-off, and the fan is intended for the mid-curve region between roughly 150 and 200 CFM where efficiency is highest. Each unit is hipot tested, run-in and sound-checked before packing, and the product is supplied under CE and RoHS declarations with RoHS-compliant materials throughout, backed by FANOVA's OEM/ODM engineering support for custom leads, connectors and control profiles.

Nominal Date
AC Backward Curved Centrifugal Fan image.png
Type FB3G150-2APL-70
Model BLDCEC72

 

Nominal Voltage VAC 230
Voltage range VAC 184~277
Current draw A 0.3±10%
Speed(RPM) min-1  3550±5%
Power consumption W 35±10%
Sound Pressure Level dB(A) 63±5%
Max. Air Flow CFM / m3 /H 268/455.4
Max. Static Pressure In.wg /Pa 1.42/355
Insulation class ~ Class B
Degree of protection ~ IP44
Control Input ~ 0~10VDC / PWM
Signal Output ~ FG (Tach output )
Connection diagram
image.png

Remarks:

Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized

Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel

Product drawing
image.png
Aerodynamic Performance Charts
image.png

Test condition:

Ⅰ.The test data is obtained under the specified environment conditions and installation mode

Ⅱ.Input Voltage---Operating voltage

Ⅲ.Temperature---Room temperature 25℃

Ⅴ.Humidity---65%RH

Safety Requirements

Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off

Ⅱ.Do not plug or unplug the fan lead plug when the fan is running

Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury

Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out

Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds

Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product

Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer

Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading

Advantages:

1. High Efficiency: The FB3G150-2APL-70 delivers 455.4 m3/h at 355 Pa while drawing only 35W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.

2. Industrial-Grade Impeller: The 150mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.

3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).

4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.

5. Easy Installation and Maintenance: Compact 150mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.

FAQ

Q1:What kind of payments do you support?

A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping

Q2.Will you provide samples?

A2: Sample is available and can be delivered within 10days

Q3:How can I choose a more suitable model?

A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.

Q4:How can I place the order?

A4:  Usually quote you within 24 hours  after  we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.

Q5:About transportation

A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive. 

Q6:How long is the warranty period?

A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000