FB3G190-24PL-70
| Nominal Voltage | VDC | 24 |
| Current draw | A | 2.4±10% |
| Speed(RPM) | min-1 | 2950±5% |
| Power consumption | W | 57.6±10% |
| Max. Air Flow | CFM / m3 /H | 364.87/620 |
| Max. Static Pressure | In.wg /Pa | 1.97/492 |
50pcs
The FB3G190-24PL-70 is a 24VDC backward curved centrifugal fan engineered for battery-powered and off-grid ventilation, where low-voltage safety and ultra-low power draw matter more than raw size. Operating on a 16~28VDC envelope at just 57.6 W and 2.4 A, it delivers a maximum airflow of 364.87 CFM (620 m3H) against a static pressure of 1.97 In.wg (492 Pa) while holding speed at 2950 RPM. The BLDCDC72 brushless DC motor keeps the electrical signature gentle enough for solar arrays, DC microgrids and mobile equipment, so a single fan can run continuously without stressing a small battery bank. A 190 mm impeller molded from glass-fiber reinforced propylene spins inside a die-cast aluminum housing, pairing lightweight rotating mass with a stiff, corrosion-tolerant frame. Speed is set by a 0~10VDC or PWM control input, letting the host controller trim airflow to demand and stretch runtime between charges. Insulation is Class B rated with an electrical strength of 1500VAC for one minute at leakage below 0.5 mA, and the dual ball-bearing system supports 70,000 hours of L10 life at 40 degrees C. Typical duties include telecom cabinet cooling, solar combiner and inverter enclosures, EV charging stations, refrigerated transport and remote sensor housings, and the unit carries CE and RoHS compliance backed by ISO 9001 manufacturing.
At the heart of the FB3G190-24PL-70 sits a 190 mm backward curved impeller injection-molded from propylene reinforced with glass fiber, a seven-blade geometry selected to keep the pressure curve steep while the rotor stays light. The reinforced polymer resists chemical attack from salt spray, battery electrolyte mist and cleaning agents, and it dampens the blade-pass vibration that a metal wheel would transmit into the cabinet. Each wheel is dynamically balanced after molding, so the 2950 RPM operating point stays smooth without external isolation. The impeller is enclosed in a die-cast aluminum endcap and housing machined with a close tip clearance, which holds the 1.97 In.wg (492 Pa) maximum static pressure at the top of the curve and keeps the 364.87 CFM (620 m3H) free-air figure stable across the 16~28VDC input range. The BLDCDC72 motor is a three-phase brushless DC design with integrated commutation electronics, delivering 57.6 W at 24VDC and 2.4 A nominal. A 0~10VDC analog input and a 25 kHz PWM input are both accepted for speed setting, with tachometer output and locked-rotor, over-current and under-voltage protection reported back to the host. Electrical strength is verified at 1500VAC for one minute with leakage current under 0.5 mA, insulation falls in Class B, and the winding is rated for ambient temperatures from -20 to +60 degrees C. Two precision ball bearings carry the shaft, lubricated for life and rated at 70,000 hours L10 at 40 degrees C, and the rotor assembly is balanced to ISO 1940 G6.3. A 20AWG cable, 500 mm long, exits the housing for power and control connections. Acoustic output is held to 68 dB(A) at one meter, measured on the free-inlet side. The fan is CE and RoHS compliant and built under an ISO 9001 quality system, with each unit hipot tested and airflow sampled before packing.
| DC Backward Curved Centrifugal Fan | ![]() |
|
| Type | FB3G190-24PL-70 | |
| Model | BLDCDC72 | |
| Nominal Voltage | VDC | 24 |
| Voltage range | VDC | 16~28 |
| Current draw | A | 2.4±10% |
| Speed(RPM) | min-1 | 2950±5% |
| Power consumption | W | 57.6±10% |
| Sound Pressure Level | dB(A) | 68±5% |
| Max. Air Flow | CFM / m3 /H | 364.87/620 |
| Max. Static Pressure | In.wg /Pa | 1.97/492 |
| Insulation class | ~ | Class B |
| Degree of protection | ~ | IP44 |
| Control Input | ~ | 0~10VDC / PWM |
| Signal Output | ~ | FG (Tach output ) |

Remarks:
Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized
Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel


Test condition:
Ⅰ.The test data is obtained under the specified environment conditions and installation mode
Ⅱ.Input Voltage---Operating voltage
Ⅲ.Temperature---Room temperature 25℃
Ⅴ.Humidity---65%RH
Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off
Ⅱ.Do not plug or unplug the fan lead plug when the fan is running
Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury
Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out
Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds
Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product
Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer
Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading
1. High Efficiency: The FB3G190-24PL-70 delivers 620 m3/h at 492 Pa while drawing only 57.6W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.
2. Industrial-Grade Impeller: The 190mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.
3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).
4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.
5. Easy Installation and Maintenance: Compact 190mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.
Q1:What kind of payments do you support?
A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping
Q2.Will you provide samples?
A2: Sample is available and can be delivered within 10days
Q3:How can I choose a more suitable model?
A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.
Q4:How can I place the order?
A4: Usually quote you within 24 hours after we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.
Q5:About transportation
A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive.
Q6:How long is the warranty period?
A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.