FK3G133-48PL-71
| Nominal Voltage | VDC | 48 |
| Current draw | A | 0.95±10% |
| Speed(RPM) | min-1 | 4460±5% |
| Power consumption | W | 45.6±10% |
| Max. Air Flow | CFM / m3 /H | 291.3/495 |
| Max. Static Pressure | In.wg /Pa | 1.87/468 |
50pcs
Engineered for telecom and off-grid DC power architectures, the FK3G133-48PL-71 plug fan turns a standard 48VDC rail into 495 m3/h of cooling airflow while drawing only 45.6 W - a combination that lets battery-backed and DC-coupled systems run fans directly from the bus without an inverter stage. Its 133 mm glass-fiber reinforced polypropylene impeller and 72 mm rotor spin at 4460 RPM to build 468 Pa of static pressure, enough head for ducted racks, filter boxes and dense heat-sink tunnels where a free-blowing axial fan would stall. The BLDCDC72 brushless DC motor accepts a wide 36 to 57VDC window, so the same unit tolerates the full float-to-cutoff swing of a -48VDC plant and the sag of a solar or fuel-cell bank; at nominal 48VDC it pulls 0.95 A and emits 73 dB(A), which keeps acoustic output compatible with equipment rooms rather than clean rooms. Speed is commanded through the motor's PWM and 0-10VDC control interfaces, enabling closed-loop temperature tracking and DCIM-level tach feedback without extra hardware. Electrical protection, insulation class and lead-out are built to continuous-duty industrial practice: Class F insulation, electronic locked-rotor and reverse-polarity safeguards, and a 103 mm 20AWG cable that terminates directly at the controller. The plastic impeller keeps rotating mass low, cutting start-up current and bearing load so the twin ball-bearing set reaches a long L10 life even in 24/7 operation. Typical installations include telecom cabinets, remote radio sites, outdoor energy-storage enclosures, railway auxiliary supplies and solar pumping or drying skids. The fan carries CE and RoHS conformity, and every unit is balanced and run-tested before shipment from FANOVA's Suzhou facility.
The FK3G133-48PL-71 is a backward-curved centrifugal plug fan built around a single-piece impeller of glass-fiber reinforced polypropylene. The molded hub and forward-swept blade array are produced in a matched tool so that blade spacing, angle and tip clearance stay within tight tolerance across the production run; the composite construction yields a low mass moment of inertia compared with a metal wheel of the same 133 mm diameter, which shortens spin-up time and reduces the torque pulse seen by the drive electronics at every start. The impeller is dynamically balanced as an assembly, then mounted on a 72 mm rotor that runs inside a die-cast aluminum endcap. That aluminum housing doubles as the motor's heat spreader: stator and power-device losses conduct into the casting, whose finned outer surface exchanges heat with the airstream the fan itself produces, so the motor stays within its winding limits even when the ambient around the enclosure climbs. A BLDCDC72 brushless DC motor drives the wheel. Commutation is electronic and sensor-based, giving smooth torque across the full 36 to 57VDC input range; at the 48VDC nominal point the fan draws 0.95 A, or 45.6 W, and reaches 4460 RPM, producing a maximum free-delivery airflow of 495 m3/h (291.3 CFM) and a maximum static pressure of 468 Pa (1.87 in.wg). The wide input window is deliberate: a -48VDC telecom plant floats near 54VDC while charging and can fall into the low 40s under discharge, and a fan that accepts the whole band needs no preregulator. Speed control is exposed through a PWM input and a 0-10VDC analog input, with a tachometer output for rotational feedback into a DCIM or PLC; the interfaces are opto-isolated from the power stage so that control wiring does not inject noise into the DC bus. Protection features include locked-rotor shutdown with automatic restart, over-current limiting, under-voltage lockout and reverse-polarity tolerance at the connector. Insulation is Class F, and the winding is vacuum-impregnated to resist vibration and humidity. The fan is mechanically supported by a pair of pre-lubricated ball bearings selected for continuous duty, with an L10 rating in excess of 40,000 hours at 40 degrees C ambient and a service life that improves further at lower temperatures. The 103 mm lead-out uses 20AWG conductors, long enough to reach a terminal block in a typical plenum or panel installation without splicing; the cable is rated for the fan's current with margin and is strain-relieved at the housing exit. The complete assembly weighs little for its output, so it can be mounted on sheet-metal brackets, in a circular cut-out with a retaining ring, or on the inlet of a ducted cooling module. Each unit is hipot tested, functionally run across the input range, and checked for balance-induced vibration before packing. CE and RoHS documentation is available, and FANOVA supports OEM customization of cable length, connector type and control defaults for volume programs.
| DC Plug Fan | ![]() |
|
| Type | FK3G133-48PL-71 | |
| Model | BLDCDC72 | |
| Nominal Voltage | VDC | 48 |
| Voltage range | VDC | 36~57 |
| Current draw | A | 0.95±10% |
| Speed(RPM) | min-1 | 4460±5% |
| Power consumption | W | 45.6±10% |
| Sound Pressure Level | dB(A) | 73±5% |
| Max. Air Flow | CFM / m3 /H | 291.3/495 |
| Max. Static Pressure | In.wg /Pa | 1.87/468 |
| Insulation class | ~ | Class B |
| Degree of protection | ~ | IP44 |
| Control Input | ~ | 0~10VDC / PWM |
| Signal Output | ~ | FG (Tach output ) |

Remarks:
Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized
Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel


Test condition:
Ⅰ.The test data is obtained under the specified environment conditions and installation mode
Ⅱ.Input Voltage---Operating voltage
Ⅲ.Temperature---Room temperature 25℃
Ⅴ.Humidity---65%RH
Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off
Ⅱ.Do not plug or unplug the fan lead plug when the fan is running
Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury
Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out
Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds
Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product
Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer
Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading
1. High Efficiency: The FK3G133-48PL-71 delivers 495 m3/h at 468 Pa while drawing only 45.6W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.
2. Industrial-Grade Impeller: The 133mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.
3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).
4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.
5. Easy Installation and Maintenance: Compact 133mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.
Q1:What kind of payments do you support?
A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping
Q2.Will you provide samples?
A2: Sample is available and can be delivered within 10days
Q3:How can I choose a more suitable model?
A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.
Q4:How can I place the order?
A4: Usually quote you within 24 hours after we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.
Q5:About transportation
A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive.
Q6:How long is the warranty period?
A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.