Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

FK3G250-12PL-90 DC Plug Fan 250mm 12V 1124 m3/h

FK3G250-12PL-90

Nominal Voltage VDC 12
Current draw A 6.0±10%
Speed(RPM) min-1  2050±5%
Power consumption W 72±10%
Max. Air Flow CFM / m3 /H 661.8/1124.5
Max. Static Pressure In.wg /Pa 1.68/420

50pcs

Brand:
FANOVA
Spu:
FK3G250-12PL-90
  • Overview
  • Recommended Products
Brief Description

Where a conventional fan would spend its entire budget just staying cool, the FK3G250-12PL-90 plug fan makes 72 W of DC power do the work of a much larger machine, delivering a maximum airflow of 1124.5 m3/h (661.8 CFM) at a peak static pressure of 420 Pa (1.68 In.wg). This 250 mm backward-curved centrifugal plug fan is built for 12 VDC systems (9 VDC minimum operating range), drawing 6.0 A and turning at 2050 RPM, so it slots directly into battery, solar, telecom and off-grid power architectures without any transformer or inverter stage. The impeller is molded from glass-fiber reinforced propylene, a lightweight composite that shrugs off moisture and many chemical vapors while keeping rotational inertia low, and it is paired with a die-cast aluminum endcap that carries the bearing loads and dissipates motor heat. A BLDCDC92 brushless DC motor drives the wheel, using electronic commutation to hold efficiency high across the speed band rather than bleeding energy as brush losses. Speed is set through a PWM control interface, allowing stepless adjustment from idle to the full 2050 RPM so airflow can be trimmed to the duty point instead of throttled by dampers. Protection and insulation are engineered for continuous duty: the motor carries Class F insulation with a winding design tolerant of elevated ambient temperatures, and onboard electronics guard against over-current, locked-rotor and under-voltage conditions. Bearings are life-lubricated and rated for the long service intervals expected in unattended equipment, and the fan terminates in a 20AWG, 500 mm flying cable for straightforward field wiring. Typical applications include low-power battery cabinets, renewable energy enclosures, air handling units, dehumidifiers, laboratory equipment and compact ventilation assemblies where every watt counts. The FK3G250-12PL-90 is manufactured under FANOVA's OEM/ODM quality system and is available with CE and RoHS compliance documentation on request.

Product Specification

The FK3G250-12PL-90 is a 250 mm diameter backward-curved centrifugal plug fan whose composite impeller is injection-molded from glass-fiber reinforced propylene. The fiber loading stiffens each blade so the wheel holds its shape and blade angle at 2050 RPM without the tip deflection seen in unfilled plastics, and the resulting blade passages are tuned for a backward-curved profile that converts velocity into pressure with low turbulence. Because the impeller weighs a fraction of a steel wheel of the same size, starting torque, bearing load and vibration are all reduced, which keeps the fan quiet (69 dB(A) at free delivery) and extends the life of the drive train. The wheel is mounted in a die-cast aluminum endcap, a rigid, dimensionally stable housing that also acts as a heat spreader for the motor, drawing heat away from the windings and electronics during continuous operation. At the heart of the unit is a BLDCDC92 brushless DC motor with an external-rotor layout and integrated commutation electronics. The drive accepts 12 VDC nominal input, works down to 9 VDC, and draws 6.0 A to produce 72 W of shaft power, an efficiency profile that suits battery-backed and solar-fed systems where conversion losses directly shorten runtime. Speed is regulated by a PWM control interface, so a host controller or building management system can command any speed between minimum and the 2050 RPM maximum; this allows the installer to balance airflow against duct resistance and to reduce speed, and therefore acoustic output, during low-load periods. Electrical ratings are 12 VDC input, 6.0 A maximum current, 72 W input power, with a maximum airflow of 1124.5 m3/h (661.8 CFM) and a maximum static pressure of 420 Pa (1.68 In.wg). The motor uses Class F insulation and its electronics include over-current, locked-rotor and under-voltage protection, so a stalled rotor or a sagging battery bank does not destroy the winding. Bearings are life-lubricated, selected for the low-vibration duty of a lightweight composite wheel, and rated for the extended service intervals expected in unattended remote installations. The electrical interface is a 20AWG, 500 mm flying lead, color-coded for power and PWM control, which connects directly to terminal blocks or controllers without a separate junction box; the cable gauge is matched to the 6.0 A maximum draw over the short lead length to keep voltage drop negligible. The fan is suited to battery cabinets, renewable energy enclosures, air handling units, dehumidifiers, laboratory and medical equipment, and compact ventilation systems where low power draw is the deciding specification. Each unit is manufactured under FANOVA's OEM/ODM quality system, function-tested before packing, and can be supplied with CE and RoHS compliance documentation on request.

Nominal Date
DC Plug Fan image.png
Type FK3G250-12PL-90
Model BLDCDC92

 

Nominal Voltage VDC 12
Voltage range VDC 9
Current draw A 6.0±10%
Speed(RPM) min-1  2050±5%
Power consumption W 72±10%
Sound Pressure Level dB(A) 69±5%
Max. Air Flow CFM / m3 /H 661.8/1124.5
Max. Static Pressure In.wg /Pa 1.68/420
Insulation class ~ Class B
Degree of protection ~ IP44
Control Input ~ 0~10VDC / PWM
Signal Output ~ FG (Tach output )
Connection diagram
image.png

Remarks:

Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized

Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel

Product drawing
image.png
Aerodynamic Performance Charts
image.png

Test condition:

Ⅰ.The test data is obtained under the specified environment conditions and installation mode

Ⅱ.Input Voltage---Operating voltage

Ⅲ.Temperature---Room temperature 25℃

Ⅴ.Humidity---65%RH

Safety Requirements

Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off

Ⅱ.Do not plug or unplug the fan lead plug when the fan is running

Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury

Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out

Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds

Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product

Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer

Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading

Advantages:

1. High Efficiency: The FK3G250-12PL-90 delivers 1124.5 m3/h at 420 Pa while drawing only 72W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.

2. Industrial-Grade Impeller: The 250mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.

3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).

4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.

5. Easy Installation and Maintenance: Compact 250mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.

FAQ

Q1:What kind of payments do you support?

A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping

Q2.Will you provide samples?

A2: Sample is available and can be delivered within 10days

Q3:How can I choose a more suitable model?

A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.

Q4:How can I place the order?

A4:  Usually quote you within 24 hours  after  we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.

Q5:About transportation

A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive. 

Q6:How long is the warranty period?

A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000