FK3G225-24PL-91
| Nominal Voltage | VDC | 24 |
| Current draw | A | 7.6±10% |
| Speed(RPM) | min-1 | 3200±5% |
| Power consumption | W | 180±10% |
| Max. Air Flow | CFM / m3 /H | 929.8/1579.9 |
| Max. Static Pressure | In.wg /Pa | 3.22/805 |
50pcs
The FK3G225-24PL-91 plug fan delivers two standout capabilities in a single compact package: a maximum airflow of 1579.9 m3/h and a maximum static pressure of 805 Pa, letting one 225 mm backward-curved impeller replace a bank of smaller axial fans in ducted and filtered air paths. Operating from a 24VDC supply across a 16 to 28VDC window, it draws 7.6 A and consumes 180 W at 3200 RPM, making it suitable for solar, battery-buffered and off-grid ventilation where safety extra-low voltage is mandatory. The BLDCDC92 brushless DC motor is integrated into a die-cast aluminum endcap that doubles as the heat sink, keeping the electronics cool under continuous duty. Speed is commanded through a 0 to 10VDC analog signal or PWM input, so airflow can be trimmed to match filter loading without external VFD hardware. The impeller is molded from glass-fiber reinforced propylene, giving a light rotating mass that limits start-up current and bearing wear while resisting many common chemical vapors. Insulation is Class F with Class B rise limits and the winding is protected against locked-rotor and over-temperature conditions. Dual ball bearings rated for 40,000 hours at 40 degrees C support maintenance-free operation in continuous ventilation. Typical installations include telecom shelters, cold-chain units, energy-storage cabinets, cleanroom make-up air and OEM air-handling equipment. The fan carries CE and RoHS declarations and is produced under ISO 9001 quality control.
The FK3G225-24PL-91 is a backward-curved centrifugal plug fan built around a 225 mm diameter impeller molded in glass-fiber reinforced propylene. The wheel uses a backward-inclined blade form with a reinforced hub and rim ring; the glass-fiber loading raises stiffness so the blades hold their profile at 3200 RPM while keeping the rotor light enough for fast acceleration and low bearing load. Each impeller is dynamically balanced to reduce vibration and tonal noise, and the finished assembly is housed in a die-cast aluminum endcap that provides both structural rigidity and a thermal path for the motor electronics. The BLDCDC92 brushless DC motor uses a 92 mm rotor diameter with permanent magnets and three-phase stator windings, commutated by integrated drive electronics mounted inside the aluminum endcap. This sensorless drive delivers 180 W of shaft power at the rated point with a current draw of 7.6 A from a 24VDC nominal bus, and it accepts an input range of 16 to 28VDC, so the fan tolerates the voltage sag of battery systems and the higher float voltage of charging cycles without shutdown. Speed control is available through a 0 to 10VDC analog interface or a PWM input, with tachometer and alarm outputs for status monitoring; the control leads are separate from the power pair so that signal wiring can be routed to a controller or DCIM node. The power cable is 20AWG, 500 mm long, rated for the full current at the stated ambient. Electrical protection includes under-voltage lockout, over-current limiting, locked-rotor shutdown and over-temperature foldback of the drive. The motor winding is Class F insulated and the design limits temperature rise to Class B values, supporting long life in enclosed cabinets. Mechanical support comes from two pre-lubricated ball bearings selected for 40,000 hours of L10 life at 40 degrees C ambient, and the rotor is mounted on a hardened shaft with a balanced fan hub to keep axial and radial loads low. At the rated operating point the fan produces 77 dB(A) sound pressure, and the backward-curved blade geometry keeps the noise spectrum broad and free of strong tones, which simplifies acoustic treatment in ducted installations. Air performance reaches 1579.9 m3/h (929.8 CFM) free delivery and 805 Pa (3.22 in.wg) shut-off static pressure, a combination that supports long duct runs, dense filter banks and multi-outlet distribution from one fan rather than several. The plug-fan format allows the unit to be mounted directly into a panel or plenum opening with a circular cutout, and the die-cast aluminum endcap is predrilled for screw fixing. The product is manufactured under an ISO 9001 quality system, is CE marked and RoHS compliant, and is available through FANOVA's OEM/ODM program with options for cable length, connector type and control firmware.
| DC Plug Fan | ![]() |
|
| Type | FK3G225-24PL-91 | |
| Model | BLDCDC92 | |
| Nominal Voltage | VDC | 24 |
| Voltage range | VDC | 16~28 |
| Current draw | A | 7.6±10% |
| Speed(RPM) | min-1 | 3200±5% |
| Power consumption | W | 180±10% |
| Sound Pressure Level | dB(A) | 77±5% |
| Max. Air Flow | CFM / m3 /H | 929.8/1579.9 |
| Max. Static Pressure | In.wg /Pa | 3.22/805 |
| Insulation class | ~ | Class B |
| Degree of protection | ~ | IP44 |
| Control Input | ~ | 0~10VDC / PWM |
| Signal Output | ~ | FG (Tach output ) |

Remarks:
Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized
Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel


Test condition:
Ⅰ.The test data is obtained under the specified environment conditions and installation mode
Ⅱ.Input Voltage---Operating voltage
Ⅲ.Temperature---Room temperature 25℃
Ⅴ.Humidity---65%RH
Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off
Ⅱ.Do not plug or unplug the fan lead plug when the fan is running
Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury
Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out
Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds
Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product
Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer
Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading
1. High Efficiency: The FK3G225-24PL-91 delivers 1579.9 m3/h at 805 Pa while drawing only 180W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.
2. Industrial-Grade Impeller: The 225mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.
3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).
4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.
5. Easy Installation and Maintenance: Compact 225mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.
Q1:What kind of payments do you support?
A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping
Q2.Will you provide samples?
A2: Sample is available and can be delivered within 10days
Q3:How can I choose a more suitable model?
A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.
Q4:How can I place the order?
A4: Usually quote you within 24 hours after we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.
Q5:About transportation
A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive.
Q6:How long is the warranty period?
A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.