Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

FK3G175-24PL-70 DC Plug Fan 190mm 24V 620 m3/h

FK3G175-24PL-70

Nominal Voltage VDC 24
Current draw A 2.4±10%
Speed(RPM) min-1  2950±5%
Power consumption W 57.6±10%
Max. Air Flow CFM / m3 /H 364.87/620
Max. Static Pressure In.wg /Pa 1.97/492

50pcs

Brand:
FANOVA
Spu:
FK3G175-24PL-70
  • Overview
  • Recommended Products
Brief Description

When a project runs on a 24VDC bus, the last thing you want is an inverter between the battery bank and the fan. The FK3G175-24PL-70 is a backward-curved plug fan built specifically to sit on low-voltage DC power: wide 16~28VDC input tolerance, only 2.4A at full load, and a modest 57.6W power draw that lets solar arrays, off-grid battery cabinets and telecom DC plants drive ventilation directly without a single AC conversion stage. That low current profile matters more than the wattage figure alone - at 24VDC nominal the unit behaves like a small appliance on the DC rail, so it can share a supply with control electronics without tripping protection or forcing a dedicated breaker. The impeller is a 190mm glass-fiber reinforced polypropylene wheel on a 72mm rotor, paired with a die-cast aluminum endcap that doubles as the motor heat sink. Air performance is 364.87 CFM (620 m3/h) at free delivery, with maximum static pressure of 1.97 In.wg (492 Pa) for short-to-medium duct runs. Speed is fixed at 2950 RPM, and a 20AWG, 500mm flying lead handles the electrical interface. Insulation and protection are rated for continuous duty, and the motor's DC design eliminates brush wear entirely. Acoustic output is 68 dB(A) at full speed. Typical installations include solar-powered container ventilation, battery energy storage cabinets, off-grid telecom shelters and 24V DC cooling enclosures for new-energy equipment. The fan carries CE and RoHS certification and is manufactured under FANOVA's Suzhou OEM/ODM quality system.

Product Specification

The FK3G175-24PL-70 is a plug fan in the FK3G175 series, designated on the data sheet as a backward centrifugal fan. Its impeller measures 190mm in diameter and is molded from polypropylene reinforced with glass fiber. The blade geometry is a backward-curved, non-overloading profile: as system resistance rises, the absorbed power falls rather than climbs, which protects the DC supply from overload when filters load up or dampers close. The choice of glass-fiber reinforced plastic delivers three practical benefits in the field - the wheel weighs a fraction of a comparable steel impeller, so start-up and run-out loads on the bearing set are lower; the material resists dilute acids, salts and many solvents that would attack galvanized steel in coastal or chemical environments; and the molding process holds blade-to-blade dimensional repeatability, which keeps the aerodynamic balance consistent from unit to unit. The hub and endcap are die-cast aluminum, machined after casting so the rotor runs concentrically inside the motor bore. The motor itself is a BLDCDC72 brushless DC design with a 72mm rotor diameter, electronically commutated in three phases with integrated Hall sensing for closed-loop speed stability. Because there are no brushes, there is no carbon dust, no commutator arcing and no wear-out mechanism tied to rotation count - service life is governed by the bearings, not the commutation. The unit accepts an input span of 16 to 28VDC, which accommodates the sag of a lead-acid or lithium pack under load as well as the higher open-circuit voltage of a charging source, and draws 2.4A at nominal 24VDC for 57.6W of input power. Running speed is 2950 RPM, producing a maximum free-air flow of 364.87 CFM (620 m3/h) and a maximum static pressure of 1.97 In.wg (492 Pa). Speed control is handled through the DC input; the drive electronics are on-board, so no external VFD is required, and the motor can be operated across its voltage window for proportional speed turndown. Electrical connection is made through a 20AWG cable with a 500mm free length, sufficient for routing to a terminal block or connector inside a control enclosure. The motor is built with Class F insulation and is intended for continuous duty at ambient temperatures typical of cabinet and shelter installations. Acoustic performance is 68 dB(A) at rated speed, measured at standard test conditions. The impeller/motor assembly is balanced before final assembly to keep vibration within limits across the operating band, and the die-cast endcap provides a rigid mounting interface that also conducts heat away from the stator. Because the fan operates from a low-voltage DC source, it is intrinsically suited to solar-direct systems, battery-backed energy storage cabinets, off-grid telecom sites and 24V DC distribution in new-energy equipment, where eliminating the DC-to-AC inverter removes a failure point and a conversion loss. The model is CE marked and RoHS compliant, and production follows FANOVA's incoming inspection, in-process and final test procedures at the Suzhou facility, with routine checks on input current, speed, airflow and noise before packing.

Nominal Date
DC Plug Fan image.png
Type FK3G175-24PL-70
Model BLDCDC72

 

Nominal Voltage VDC 24
Voltage range VDC 16~28
Current draw A 2.4±10%
Speed(RPM) min-1  2950±5%
Power consumption W 57.6±10%
Sound Pressure Level dB(A) 68±5%
Max. Air Flow CFM / m3 /H 364.87/620
Max. Static Pressure In.wg /Pa 1.97/492
Insulation class ~ Class B
Degree of protection ~ IP44
Control Input ~ 0~10VDC / PWM
Signal Output ~ FG (Tach output )
Connection diagram
image.png

Remarks:

Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized

Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel

Product drawing
image.png
Aerodynamic Performance Charts
image.png

Test condition:

Ⅰ.The test data is obtained under the specified environment conditions and installation mode

Ⅱ.Input Voltage---Operating voltage

Ⅲ.Temperature---Room temperature 25℃

Ⅴ.Humidity---65%RH

Safety Requirements

Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off

Ⅱ.Do not plug or unplug the fan lead plug when the fan is running

Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury

Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out

Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds

Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product

Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer

Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading

Advantages:

1. High Efficiency: The FK3G175-24PL-70 delivers 620 m3/h at 492 Pa while drawing only 57.6W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.

2. Industrial-Grade Impeller: The 190mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.

3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).

4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.

5. Easy Installation and Maintenance: Compact 190mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.

FAQ

Q1:What kind of payments do you support?

A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping

Q2.Will you provide samples?

A2: Sample is available and can be delivered within 10days

Q3:How can I choose a more suitable model?

A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.

Q4:How can I place the order?

A4:  Usually quote you within 24 hours  after  we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.

Q5:About transportation

A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive. 

Q6:How long is the warranty period?

A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000