FB3G220-24PL-92
| Nominal Voltage | VDC | 24 |
| Current draw | A | 3.3±10% |
| Speed(RPM) | min-1 | 2760±5% |
| Power consumption | W | 80±10% |
| Max. Air Flow | CFM / m3 /H | 577.02/980.5 |
| Max. Static Pressure | In.wg /Pa | 1.94/485 |
50pcs
The FB3G220-24PL-92 is a 24VDC backward curved centrifugal fan built for projects that must run entirely from a low-voltage DC bus, where safety and battery economics matter as much as airflow. Operating from a 16-28VDC window at just 80W, it moves up to 980.5 m3/h (577.02 CFM) and develops 485 Pa (1.94 In.wg) of static pressure, making it a genuinely compact powerhouse for off-grid, solar, telecom-cabinet and new-energy equipment. The fan is driven by an FANOVA BLDCDC92 brushless DC motor turning a 220 mm impeller molded from glass-fiber reinforced propylene, so the rotating assembly stays light and the current draw stays modest (3.3 A nominal at 24VDC). Because the whole package is a DC appliance, speed is set through a 0-10VDC or PWM control input rather than a transformer-fed AC drive, which lets a system controller throttle the fan to match real thermal load and protect battery runtime. Electrical protection and insulation are engineered for industrial duty, and the long-life ball bearing system is rated for continuous operation to keep service intervals long and maintenance costs low. Typical installations include outdoor telecom enclosures, solar inverter cooling, energy-storage cabinets, EV charging equipment and compact air-handling units. The unit is CE and RoHS compliant and is produced under FANOVA's ISO 9001 quality system, with a 20AWG 500 mm flying lead for straightforward field wiring. For engineers sizing a quiet, low-power DC air mover that slots directly into a 24V architecture, the FB3G220-24PL-92 is the efficient answer.
At the heart of the FB3G220-24PL-92 sits a 220 mm diameter backward curved impeller injection-molded from glass-fiber reinforced propylene. The glass-fiber loading raises tensile stiffness and creep resistance well beyond unfilled plastic, so the blades hold their aerofoil profile at 2760 RPM without flutter, while the compound keeps rotating mass low enough to limit start-up inrush on a 24VDC supply. The backward curved blade geometry produces a rising pressure characteristic that resists stall in long duct runs, and the die-cast aluminum endcap and housing form a rigid, dimensionally stable cradle that damps vibration and helps dissipate motor heat. Air performance peaks at 980.5 m3/h free delivery and 485 Pa shut-off pressure, a balance point suited to filter-loaded enclosures and compact AHUs where a forward curved wheel would run out of pressure.
Drive is provided by the BLDCDC92 brushless DC motor, a 92 mm rotor design with integrated commutation electronics. The motor is rated 24VDC nominal across a 16-28VDC input range, drawing 3.3 A and 80 W at the duty point, and it reaches 2760 RPM with electronic speed regulation that holds setpoint against supply sag and load change. Speed is commanded through an analog 0-10VDC interface or a PWM duty input, allowing stepless turn-down for night setback, battery-saver modes or acoustic limiting; a tachometer/fault output is available for DCIM or BMS monitoring. Electrical protection covers locked-rotor and over-current shutdown, under/over-voltage cut-out across the stated range, and reverse-polarity tolerance on the supply terminals. Insulation is Class B with a dielectric strength tested to 500VAC for one minute, keeping creepage margins healthy in humid cabinet environments.
Mechanically, the rotor runs in pre-lubricated dual ball bearings selected for horizontal or vertical mounting; the bearing system is rated L10 at 40,000 hours at 40 degrees C ambient, and the sealed construction retains grease for life. The 20AWG, 500 mm flying lead is stripped and tinned for direct termination into a controller or terminal block, with lead colors identifying positive, negative, control and tach signals. Acoustic output is 71.4 dB(A) at maximum speed measured at one meter, and the backward curved blade spacing is tuned to spread tonal energy so the sound is broadband rather than whining. The die-cast aluminum housing is finished for corrosion resistance, and the impeller is balanced dynamically to ISO 1940 G6.3 to hold vibration below 2.8 mm/s.
Every unit is hipot tested, run-in and performance sampled before packing. The FB3G220-24PL-92 carries CE and RoHS declarations and is manufactured in FANOVA's Suzhou plant under ISO 9001, with traceability on motor lot and balance records. It is intended for solar inverters, energy-storage thermal management, outdoor telecom cabinets, EV charger cooling and light industrial ventilation where a 24VDC bus, low power draw and long bearing life define the design brief.
| DC Backward Curved Centrifugal Fan | ![]() |
|
| Type | FB3G220-24PL-92 | |
| Model | BLDCDC92 | |
| Nominal Voltage | VDC | 24 |
| Voltage range | VDC | 16~28 |
| Current draw | A | 3.3±10% |
| Speed(RPM) | min-1 | 2760±5% |
| Power consumption | W | 80±10% |
| Sound Pressure Level | dB(A) | 71.4±5% |
| Max. Air Flow | CFM / m3 /H | 577.02/980.5 |
| Max. Static Pressure | In.wg /Pa | 1.94/485 |
| Insulation class | ~ | Class B |
| Degree of protection | ~ | IP44 |
| Control Input | ~ | 0~10VDC / PWM |
| Signal Output | ~ | FG (Tach output ) |

Remarks:
Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized
Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel


Test condition:
Ⅰ.The test data is obtained under the specified environment conditions and installation mode
Ⅱ.Input Voltage---Operating voltage
Ⅲ.Temperature---Room temperature 25℃
Ⅴ.Humidity---65%RH
Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off
Ⅱ.Do not plug or unplug the fan lead plug when the fan is running
Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury
Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out
Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds
Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product
Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer
Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading
1. High Efficiency: The FB3G220-24PL-92 delivers 980.5 m3/h at 485 Pa while drawing only 80W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.
2. Industrial-Grade Impeller: The 220mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.
3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).
4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.
5. Easy Installation and Maintenance: Compact 220mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.
Q1:What kind of payments do you support?
A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping
Q2.Will you provide samples?
A2: Sample is available and can be delivered within 10days
Q3:How can I choose a more suitable model?
A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.
Q4:How can I place the order?
A4: Usually quote you within 24 hours after we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.
Q5:About transportation
A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive.
Q6:How long is the warranty period?
A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.