Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

FK3G133-2APL-52 EC Plug Fan 133mm 230V 291 m3/h

FK3G133-2APL-52

Nominal Voltage VAC 230
Current draw A 0.3±10%
Speed(RPM) min-1  4000±5%
Power consumption W 30±10%
Max. Air Flow CFM / m3 /H 171.3/291
Max. Static Pressure In.wg /Pa 2.1/524

50pcs

Brand:
FANOVA
Spu:
FK3G133-2APL-52
  • Overview
  • Recommended Products
Brief Description

The FK3G133-2APL-52 is a 230VAC EC plug fan that proves energy efficiency does not require exotic hardware: running at just 30 W, it draws a mere 0.3 A at 4000 RPM while still delivering up to 171.3 CFM (291 m3H) and 2.1 In.wg (524 Pa) of static pressure. This is the drop-in answer for anyone replacing an AC impeller who wants to cut standby and running watts, because the BLDCEC53 electronically commutated motor carries its own integrated drive and accepts any supply from 184 to 277 VAC, 50 or 60 Hz, without an external transformer or VFD. The 133 mm impeller is molded from propylene reinforced with glass fiber, so the rotating mass stays low, the motor sees a light inertial load at start-up and the part resists the mild chemical and moisture exposure common in air-handling cabinets. A die-cast aluminum endcap grounds the whole rotating assembly in a rigid, thermally stable housing that holds bearing alignment over years of continuous duty. Speed is set by a 0-10 VDC analog signal or a PWM input through the onboard control electronics, giving stepless modulation from a whisper-quiet low end up to the full 4000 RPM rating. Insulation is Class B with an electronically protected winding, and the permanently lubricated ball-bearing system is specified for 40,000 hours at 40 C ambient, which equates to roughly four and a half years of uninterrupted operation. At 66 dB(A) the fan suits office, laboratory and light-commercial ventilation where the unit sits close to occupied space. Target duties include fan-coil and CRAC units, VAV terminal boxes, ERV cores, and compact cooling racks. The fan is CE and RoHS compliant and is built in an ISO 9001 facility, with UL-recognized component options available on request.

Product Specification

At the heart of the FK3G133-2APL-52 sits a single-piece centrifugal impeller of 133 mm nominal diameter, injection molded from glass-fiber reinforced propylene. The backward-curved blade profile is generated with 11 blades set at an outlet angle chosen to keep the pressure curve stable from free delivery through to the 524 Pa maximum, so the fan does not fall into surge when a filter loads up. Glass-fiber loading raises the blade stiffness enough to suppress flutter at 4000 RPM while keeping the impeller light, which limits bearing loads and start-up inrush. The impeller is dynamically balanced in two planes to ISO 1940 G6.3 before assembly. The rotor and stator form the BLDCEC53 outer-rotor motor, a three-phase electronically commutated design with surface-mounted permanent magnets and concentrated windings. Commutation is handled by an integrated inverter board potted onto the motor, so no external drive is needed and the 500 mm, 20AWG cable carries only mains and control signals. Input range is 184 to 277 VAC at 50 or 60 Hz, with 230 VAC nominal; current draw is 0.3 A and shaft power 30 W at the 4000 RPM design point. The control interface provides a 0-10 VDC analog input and a 25 kHz PWM input, both referenced to the fan's internal ground, plus a tachometer output for speed feedback and a fault alarm line. Speed can be trimmed from roughly 10 percent to 100 percent, and the electronics include soft-start, locked-rotor and over-temperature protection. The motor winding is Class B insulated and the electronics are conformally coated for humidity tolerance. Mechanical support comes from the die-cast aluminum endcap, which combines the bearing housing, the mounting flange and the heatsink for the inverter in one casting; the aluminum keeps bearing bores round and conducts motor heat away from the windings. Two pre-lubricated deep-groove ball bearings carry the rotor, rated L10 at 40,000 hours at 40 C ambient, and the assembly is designed for shaft-up, shaft-down or horizontal mounting without re-oiling. The fan weighs approximately 1.3 kg and mounts through the four-hole flange on the endcap. Electrical connection is by flying leads on the 500 mm 20AWG cable, color-coded for line, neutral, earth, control and tachometer. EMC performance meets EN 61000-6-2 and EN 61000-6-4, safety is to EN 60335-1, and the unit carries CE and RoHS marks. Every fan is run-in and hipot tested before packing, and the product is manufactured under an ISO 9001 quality system with full traceability by serial number.

Nominal Date
AC Plug Fan image.png
Type FK3G133-2APL-52
Model BLDCEC53

 

Nominal Voltage VAC 230
Voltage range VAC 184~277
Current draw A 0.3±10%
Speed(RPM) min-1  4000±5%
Power consumption W 30±10%
Sound Pressure Level dB(A) 66±5%
Max. Air Flow CFM / m3 /H 171.3/291
Max. Static Pressure In.wg /Pa 2.1/524
Insulation class ~ Class B
Degree of protection ~ IP44
Control Input ~ 0~10VDC / PWM
Signal Output ~ FG (Tach output )
Connection diagram
image.png

Remarks:

Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized

Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel

Product drawing
image.png
Aerodynamic Performance Charts
image.png

Test condition:

Ⅰ.The test data is obtained under the specified environment conditions and installation mode

Ⅱ.Input Voltage---Operating voltage

Ⅲ.Temperature---Room temperature 25℃

Ⅴ.Humidity---65%RH

Safety Requirements

Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off

Ⅱ.Do not plug or unplug the fan lead plug when the fan is running

Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury

Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out

Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds

Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product

Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer

Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading

Advantages:

1. High Efficiency: The FK3G133-2APL-52 delivers 291 m3/h at 524 Pa while drawing only 30W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.

2. Industrial-Grade Impeller: The 133mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.

3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).

4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.

5. Easy Installation and Maintenance: Compact 133mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.

FAQ

Q1:What kind of payments do you support?

A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping

Q2.Will you provide samples?

A2: Sample is available and can be delivered within 10days

Q3:How can I choose a more suitable model?

A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.

Q4:How can I place the order?

A4:  Usually quote you within 24 hours  after  we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.

Q5:About transportation

A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive. 

Q6:How long is the warranty period?

A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000