Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

FK3G133-24PL-72 DC Plug Fan 133mm 24V 457 m3/h

FK3G133-24PL-72

Nominal Voltage VDC 24
Current draw A 1.3±10%
Speed(RPM) min-1  3900±5%
Power consumption W 31.2±10%
Max. Air Flow CFM / m3 /H 268.7/456.6
Max. Static Pressure In.wg /Pa 1.52/380

50pcs

Brand:
FANOVA
Spu:
FK3G133-24PL-72
  • Overview
  • Recommended Products
Brief Description

When a 64 dB(A) sound ceiling matters more than raw airflow, the FK3G133-24PL-72 plug fan is the one to specify. Running on a 24VDC nominal supply (16 to 28VDC operating window) at only 1.3 A and 31.2 W, this 133 mm backward-curved centrifugal impeller delivers up to 268.7 CFM (456.6 m3/h) at free air and 1.52 in.wg (380 Pa) at shut-off, so it moves real air through a filter or duct run without ever rising above conversational speech levels. The heart of the unit is a BLDCDC72 brushless DC motor with integrated commutation electronics; speed is set by a 0-10V analog command or PWM input, and a tach output reports rotor position back to the host controller for closed-loop control. Electrical safety is built in: the low-voltage 24VDC architecture keeps the fan in the SELV domain, making it suitable for solar, off-grid, battery and new-energy cabinets where mains potential is neither available nor desirable, while the class F insulation system and locked-rotor, over-current and reverse-polarity protection guard the electronics against field faults. The impeller is molded from glass-fiber reinforced polypropylene, a lightweight, chemically resistant and cost-effective material that also damps vibration; it is mounted in a die-cast aluminum endcap that acts as a rigid heat sink for the motor and keeps the rotating assembly true at 3900 RPM. Bearings are pre-lubricated ball types rated for 40,000 hours at 40 degrees C ambient (L10), so maintenance-free service life matches the design life of the equipment around it. Typical installations include laboratory fume hoods and clean benches, medical and dental equipment, telecom and IT enclosures, air purifiers, dehumidifiers, vending and refrigeration units, and any 24VDC ventilation path that must stay quiet. The fan is CE and RoHS compliant and is produced under an ISO 9001 quality system, with each unit balanced and run-tested before shipment.

Product Specification

The FK3G133-24PL-72 is a plug-fan assembly built around a 133 mm diameter backward-curved centrifugal impeller, and every mechanical decision in it serves the quiet, low-power 24VDC duty it was designed for. The impeller is injection molded in glass-fiber reinforced polypropylene: the fiber loading raises tensile and creep strength while the polypropylene matrix keeps mass low, resists most acids, bases and solvents found in air-handling service, and contributes internal damping that suppresses the blade-pass tone. The backward-curved blade form, with a blade count chosen to spread acoustic energy across octave bands rather than concentrate it, produces a rising pressure characteristic that is stable from free delivery to shut-off, so the fan can be throttled into a filter or long duct run without falling into surge. Rotation is counterclockwise viewed from the inlet, and the impeller is dynamically balanced to ISO 1940 G6.3 before final assembly. The impeller is enclosed by a die-cast aluminum endcap that doubles as the motor housing; aluminum was selected for its dimensional stability, its ability to conduct heat away from the stator, and its corrosion resistance in humid or mildly aggressive atmospheres. The motor is a BLDCDC72 electronically commutated brushless DC machine with a 72 mm rotor diameter, three-phase stator and integrated drive electronics mounted on the endcap. Hall sensors provide rotor position, and the controller performs sinusoidal commutation to minimize torque ripple and the associated low-frequency noise. At 24VDC nominal the fan draws 1.3 A and consumes 31.2 W at the 3900 RPM design point, producing a maximum free-air flow of 268.7 CFM (456.6 m3/h) and a maximum static pressure of 1.52 in.wg (380 Pa). The input voltage window is 16 to 28VDC, which allows direct operation from 24V battery banks across their full charge and discharge range without an external regulator. Speed control is through a 0-10V analog input or a 25 kHz PWM duty signal, with a frequency (tach) output for speed feedback and an alarm output for fault reporting; the control leads are part of the 20AWG, 103 mm flying cable that also carries the DC supply. Protection features include locked-rotor shutdown with automatic restart, over-current limiting, under-voltage lockout and reverse-polarity protection. The insulation system is class F, the winding is rated for continuous duty at 40 degrees C ambient, and dielectric strength is tested at 500 VAC for one minute. The rotor runs in two pre-lubricated, shielded ball bearings selected for low noise; their L10 rating is 40,000 hours at 40 degrees C, and the bearing seats are machined to a controlled interference fit to prevent outer-race creep. Acoustic output is 64 dB(A) at one meter at the rated point, measured in a semi-anechoic chamber per ISO 3744. The FK3G133-24PL-72 meets CE (EMC and LVD as applicable to 24VDC equipment) and RoHS requirements, is manufactured in an ISO 9001 certified facility, and is 100 percent run-tested for airflow, current, speed and noise before packing.

Nominal Date
DC Plug Fan image.png
Type FK3G133-24PL-72
Model BLDCDC72

 

Nominal Voltage VDC 24
Voltage range VDC 16~28
Current draw A 1.3±10%
Speed(RPM) min-1  3900±5%
Power consumption W 31.2±10%
Sound Pressure Level dB(A) 64±5%
Max. Air Flow CFM / m3 /H 268.7/456.6
Max. Static Pressure In.wg /Pa 1.52/380
Insulation class ~ Class B
Degree of protection ~ IP44
Control Input ~ 0~10VDC / PWM
Signal Output ~ FG (Tach output )
Connection diagram
image.png

Remarks:

Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized

Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel

Product drawing
image.png
Aerodynamic Performance Charts
image.png

Test condition:

Ⅰ.The test data is obtained under the specified environment conditions and installation mode

Ⅱ.Input Voltage---Operating voltage

Ⅲ.Temperature---Room temperature 25℃

Ⅴ.Humidity---65%RH

Safety Requirements

Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off

Ⅱ.Do not plug or unplug the fan lead plug when the fan is running

Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury

Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out

Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds

Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product

Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer

Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading

Advantages:

1. High Efficiency: The FK3G133-24PL-72 delivers 456.6 m3/h at 380 Pa while drawing only 31.2W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.

2. Industrial-Grade Impeller: The 133mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.

3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).

4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.

5. Easy Installation and Maintenance: Compact 133mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.

FAQ

Q1:What kind of payments do you support?

A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping

Q2.Will you provide samples?

A2: Sample is available and can be delivered within 10days

Q3:How can I choose a more suitable model?

A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.

Q4:How can I place the order?

A4:  Usually quote you within 24 hours  after  we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.

Q5:About transportation

A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive. 

Q6:How long is the warranty period?

A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000