Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

FF3G120-24GL-70 DC Forward Curved Centrifugal Fan 120mm 24V 326 m3/h

FF3G120-24GL-70

Nominal Voltage VDC 24
Current draw A 2.8±10%
Speed(RPM) min-1  2580±5%
Power consumption W 67±10%
Max. Air Flow CFM / m3 /H 191.8/325.9
Max. Static Pressure In.wg /Pa 1.24/310

50pcs

Brand:
FANOVA
Spu:
FF3G120-24GL-70
  • Overview
  • Recommended Products
Brief Description

Engineered for off-grid and battery-backed air movement, the FF3G120-24GL-70 is a 24VDC forward curved centrifugal fan that delivers up to 191.8 CFM (325.9 m3/h) at 1.24 in.wg (310 Pa) while drawing only 67 W at 2.8 A - a combination that lets solar, telecom and remote-cabinet designers run continuous ventilation from a modest DC supply. Its superpowers are low-voltage safety and extreme power economy: at 24VDC nominal (usable from 16 to 28VDC) the blower can be fed directly from a 24V battery bank, a PV charge controller load output or a DC microgrid without any inverter stage, and the 67 W consumption means a single 100 W panel can support a duty-cycled ventilation strategy. The BLDCDC72 brushless DC motor spins the 120 mm galvanized steel impeller to 2580 RPM, producing strong static pressure for its class so the unit can push air through duct runs, filters and cabinet plenums rather than merely stirring room air. Speed is set by a 0-10VDC or PWM control signal, allowing closed-loop temperature or differential-pressure control, and the fan reports speed feedback for monitoring. Electrical protection and insulation follow the design rules for low-voltage industrial equipment, with locked-rotor and reverse-polarity protection built into the drive electronics, and the ball-bearing system is rated for long continuous life at these low operating temperatures. Noise stays at 65 dB(A), acceptable for equipment rooms, kiosks and enclosure cooling where operators are present. Typical applications include solar-powered ventilation, off-grid telecom shelters, EV charging cabinets, battery energy storage racks, remote monitoring stations and marine DC systems. The fan is CE and RoHS compliant and is produced under FANOVA's ISO 9001 quality system in Suzhou, China.

Product Specification

The FF3G120-24GL-70 is built around a 120 mm diameter forward curved impeller fabricated from galvanized steel sheet, with a multi-blade (approximately 40-blade) drum profile that is continuously seam-rolled and riveted to maintain concentricity at 2580 RPM. Galvanized steel was selected over molded plastic because it resists elevated discharge temperatures, does not embrittle with age, and holds blade geometry under the centrifugal loads generated at the impeller periphery; the zinc coating provides corrosion resistance for humid or coastal installations. The impeller is mounted on a balanced rotor and housed in a die-cast aluminum endcap and casing that combines structural stiffness with effective heat spreading from the motor, keeping winding temperatures low even when the fan is installed in a warm enclosure. The rotor diameter of 72 mm reflects the BLDCDC72 brushless DC motor platform, a three-phase electronically commutated design with integrated Hall sensing and a sinusoidal commutation drive. The motor operates from a 16 to 28VDC input, draws 2.8 A at the 24VDC nominal point, and delivers 67 W of shaft power at 2580 RPM; the wide input window means the fan continues to run as a 24V battery discharges, avoiding the sudden shutdown that afflicts fixed-voltage DC fans. Speed control is via a 0-10VDC analog input or a 25 kHz PWM duty signal, with a tachometer/frequency-generator output available for speed verification and stall detection; start-up is soft-ramped to limit inrush on shared DC buses. The electrical interface is a 500 mm flying lead in 20AWG wire, with color-coded conductors for positive, negative, control and feedback, and the drive includes reverse-polarity protection, over-current limiting and locked-rotor shutdown with automatic restart. Bearings are pre-lubricated ball bearings selected for low-speed DC duty, giving an L10 life suitable for continuous 24/7 operation at rated temperature and allowing any-orientation mounting; the rotor is dynamically balanced to ISO 1940 G6.3 to control vibration and bearing load. Insulation is Class B rated with a dielectric withstand test applied to the stator assembly, and the electronics are conformally protected against humidity and dust ingress for indoor and sheltered outdoor use. Airflow reaches 191.8 CFM (325.9 m3/h) at free delivery with a maximum static pressure of 1.24 in.wg (310 Pa), and sound pressure is held to 65 dB(A) at one meter. Each unit is routine-tested for current, speed, airflow and noise before packing, and production is controlled under ISO 9001 with CE and RoHS declarations issued for the series. FANOVA (Suzhou Xinhengxin Air-conditioning & Refrigeration) supplies the FF3G120-24GL-70 as a standard catalog model and supports OEM voltage, cable and connector customization for off-grid and new-energy ventilation programs.

Nominal Date
DC Forward Curved Centrifugal Fan image.png
Type FF3G120-24GL-70
Model BLDCDC72

 

Nominal Voltage VDC 24
Voltage range VDC 16~28
Current draw A 2.8±10%
Speed(RPM) min-1  2580±5%
Power consumption W 67±10%
Sound Pressure Level dB(A) 65±5%
Max. Air Flow CFM / m3 /H 191.8/325.9
Max. Static Pressure In.wg /Pa 1.24/310
Insulation class ~ Class B
Degree of protection ~ IP44
Control Input ~ 0~10VDC / PWM
Signal Output ~ FG (Tach output )
Connection diagram
image.png

Remarks:

Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized

Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel

Product drawing
image.png
Aerodynamic Performance Charts
image.png

Test condition:

Ⅰ.The test data is obtained under the specified environment conditions and installation mode

Ⅱ.Input Voltage---Operating voltage

Ⅲ.Temperature---Room temperature 25℃

Ⅴ.Humidity---65%RH

Safety Requirements

Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off

Ⅱ.Do not plug or unplug the fan lead plug when the fan is running

Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury

Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out

Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds

Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product

Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer

Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading

Advantages:

1. High Efficiency: The FF3G120-24GL-70 delivers 325.9 m3/h at 310 Pa while drawing only 67W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.

2. Industrial-Grade Impeller: The 120mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.

3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).

4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.

5. Easy Installation and Maintenance: Compact 120mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.

FAQ

Q1:What kind of payments do you support?

A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping

Q2.Will you provide samples?

A2: Sample is available and can be delivered within 10days

Q3:How can I choose a more suitable model?

A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.

Q4:How can I place the order?

A4:  Usually quote you within 24 hours  after  we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.

Q5:About transportation

A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive. 

Q6:How long is the warranty period?

A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000