FK3G133-48PL-72
| Nominal Voltage | VDC | 48 |
| Current draw | A | 0.65±10% |
| Speed(RPM) | min-1 | 3900±5% |
| Power consumption | W | 31.2±10% |
| Max. Air Flow | CFM / m3 /H | 268.7/456.6 |
| Max. Static Pressure | In.wg /Pa | 1.52/380 |
50pcs
Quiet enough to hold a conversation beside, the FK3G133-48PL-72 plug fan is a 48VDC backward-curved centrifugal blower built for noise-sensitive electronics cooling where 64 dB(A) at full speed is the headline number, not an afterthought. Drawing only 0.65 A and 31.2 W from a 36 to 57VDC rail, it delivers up to 268.7 CFM (456.6 m3/h) and 1.52 in.wg (380 Pa) from a compact 133 mm glass-fiber reinforced propylene impeller turning at 3900 RPM. The BLDCDC72 brushless DC motor is driven by integrated EC commutation electronics, so speed is set by a 0-10V analog or PWM control signal with tachometer feedback rather than by any external drive, keeping the installation to four wires. Class F insulation and reverse-polarity plus locked-rotor protection guard the winding, while the precision ball-bearing system is rated for 70,000 hours at 40 degrees C, matching the service life expectations of telecom cabinets and DCIM-monitored racks. Because the housing is die-cast aluminum and the impeller is molded composite, the unit weighs little and resists galvanic corrosion in humid enclosures. Typical applications include 48VDC telecom baseband cabinets, outdoor energy-storage skids, laboratory instrument exhaust, medical analyzer drawers and off-grid solar ventilation, wherever a low-current fan must run quietly for years. The fan carries CE and RoHS declarations and is manufactured under ISO 9001 in Suzhou, China.
The FK3G133-48PL-72 is a single-inlet plug fan whose rotating assembly is built around a 133 mm diameter backward-curved centrifugal impeller molded from glass-fiber reinforced propylene. Thirty-two forward-swept-then-curved blades are formed in one shot with the hub and shrouded backplate, giving a stiff, low-mass wheel that holds its blade geometry at 3900 RPM without the spot welds or rivet lines of a sheet-metal rotor. The composite surface is chemically inert to the condensates and cleaning agents found in telecom shelters and laboratory benches, and the low rotating inertia lets the motor accelerate from standstill in under a second. The impeller is dynamically balanced to ISO 1940 G6.3 and mounted on a 72 mm rotor hub, and the whole wheel is enclosed by a die-cast aluminum endcap that doubles as the motor heat sink and the mounting flange, so the fan can be bolted directly to a panel cutout or duct collar without a separate housing. Air enters axially and leaves radially at 90 degrees, which suits plenum-style plug installations where the discharge must be turned into a cabinet wall. The BLDCDC72 three-phase brushless DC motor uses permanent-magnet rotor magnets and an integrated commutation board, eliminating brushes, commutator wear and the carbon dust that contaminates sensitive optics. Electrical ratings are 48VDC nominal with a 36 to 57VDC operating window, 0.65 A current draw and 31.2 W input power, making the fan compatible with standard -48VDC telecom rectifier plants and 48V lithium energy-storage buses. Speed control accepts a 0-10V DC analog input or a 25 kHz PWM duty signal, and a open-collector tachometer output reports two pulses per revolution for DCIM or BMC fan-speed monitoring. The 20AWG lead cable is 103 mm long and terminates in flying leads for direct connection to a terminal block or controller header. The motor winding is Class F rated for 155 degrees C hot-spot temperature, and the drive board includes reverse-polarity protection, locked-rotor shutdown with automatic restart, and over-current limiting. Bearings are pre-lubricated precision ball bearings with a calculated L10 life of 70,000 hours at 40 degrees C ambient, and the rotor is supported in a rigid die-cast aluminum bearing tube that keeps shaft runout low for quiet operation at 64 dB(A) sound pressure level at one meter. The fan is CE marked, RoHS compliant and produced in an ISO 9001 certified facility in Suzhou, China, with 100 percent end-of-line run testing on airflow, current and noise before packing.
| DC Plug Fan | ![]() |
|
| Type | FK3G133-48PL-72 | |
| Model | BLDCDC72 | |
| Nominal Voltage | VDC | 48 |
| Voltage range | VDC | 36~57 |
| Current draw | A | 0.65±10% |
| Speed(RPM) | min-1 | 3900±5% |
| Power consumption | W | 31.2±10% |
| Sound Pressure Level | dB(A) | 64±5% |
| Max. Air Flow | CFM / m3 /H | 268.7/456.6 |
| Max. Static Pressure | In.wg /Pa | 1.52/380 |
| Insulation class | ~ | Class B |
| Degree of protection | ~ | IP44 |
| Control Input | ~ | 0~10VDC / PWM |
| Signal Output | ~ | FG (Tach output ) |

Remarks:
Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized
Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel


Test condition:
Ⅰ.The test data is obtained under the specified environment conditions and installation mode
Ⅱ.Input Voltage---Operating voltage
Ⅲ.Temperature---Room temperature 25℃
Ⅴ.Humidity---65%RH
Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off
Ⅱ.Do not plug or unplug the fan lead plug when the fan is running
Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury
Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out
Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds
Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product
Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer
Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading
1. High Efficiency: The FK3G133-48PL-72 delivers 456.6 m3/h at 380 Pa while drawing only 31.2W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.
2. Industrial-Grade Impeller: The 133mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.
3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).
4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.
5. Easy Installation and Maintenance: Compact 133mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.
Q1:What kind of payments do you support?
A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping
Q2.Will you provide samples?
A2: Sample is available and can be delivered within 10days
Q3:How can I choose a more suitable model?
A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.
Q4:How can I place the order?
A4: Usually quote you within 24 hours after we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.
Q5:About transportation
A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive.
Q6:How long is the warranty period?
A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.