Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

FB3G560-4AAL-10 EC Backward Curved Centrifugal Fan 560mm 380V 12200 m3/h

FB3G560-4AAL-10

Nominal Voltage VAC 380
Current draw A 2.7±10%
Speed(RPM) min-1  1450±5%
Power consumption W 1800±10%
Max. Air Flow CFM / m3 /H 7179.7/12200
Max. Static Pressure In.wg /Pa 3.24/810

10pcs

Brand:
FANOVA
Spu:
FB3G560-4AAL-10
  • Overview
  • Recommended Products
Brief Description

When a single air mover must carry the whole duty of a large air-handling cabinet, the FB3G560-4AAL-10 backward curved centrifugal fan is built to replace a bank of smaller blowers with one high-output impeller. Its 560 mm die-cast aluminum wheel delivers a maximum air flow of 12200 m3/h (7179.7 CFM) while still developing 810 Pa (3.24 In.wg) of static pressure, so long duct runs and dense filter banks no longer force engineers to double up on fans. Drive comes from a BLDCEC137 electronically commutated motor rated 1800 W at 380VAC (usable from 304VAC), drawing 2.7 A and turning at 1450 RPM, a high-power, low-speed combination that pushes volume without the shrill tip speed of small high-RPM rotors. Speed is commanded over the motor's EC control interface, allowing 0-10V or PWM trimming to match actual system resistance and cut energy at part load. The motor is built with Class F insulation and IP54-class environmental protection, and the pre-lubricated ball bearing set is specified for 40,000 hours of L10 life at rated conditions. At 75 dB(A) it suits plant rooms, central air-handling units, cleanroom recirculation, data center cooling walls, drying tunnels and new-energy process ventilation. The fan carries CE and RoHS declarations and is produced under ISO 9001 quality management, with CCC available for the domestic market. FANOVA builds this model as an OEM/ODM platform, so mounting flanges, cable lengths and control cards can be tailored to the enclosure.

Product Specification

The FB3G560-4AAL-10 is a single-inlet backward curved centrifugal fan assembled around a 560 mm diameter impeller die-cast in aluminum alloy and dynamically balanced to ISO 1940 G6.3 before final assembly. The wheel carries a dense array of backward inclined blades that curve away from the direction of rotation, a geometry that produces a steep, stable pressure curve and keeps the power draw from rising sharply as system resistance increases. Both the impeller and the endcap housing are cast in the same aluminum alloy, giving the air path consistent thermal expansion and corrosion behavior, and the housing is machined to hold tight radial clearance so leakage losses stay low. Air enters axially and leaves through a rectangular discharge sized for standard duct connections. The rotor measures 137 mm in diameter and is coupled directly to the impeller, eliminating belt losses and maintenance. Behind it sits a BLDCEC137 electronically commutated motor: a three-phase permanent magnet synchronous machine with integrated commutation electronics, rated 1800 W at 380VAC with an operating window down to 304VAC, drawing 2.7 A and running at 1450 RPM. The EC architecture means the fan can be speed-controlled without an external variable frequency drive; the control interface accepts a 0-10V analog signal or a PWM input, and a tachometer output reports actual rotor speed back to the building management system. Electrical termination is via an 18AWG cable, 372 mm long, with the conductor gauge matched to the 2.7 A running current so voltage drop across the lead stays negligible. The motor is wound with Class F insulation and the electronics are potted against vibration and humidity, with an environmental rating in the IP54 class. Bearings are sealed, pre-lubricated ball bearings selected for an L10 rating life of 40,000 hours at rated load, and the shaft is supported to keep runout low across the full speed range. The fan is intended for continuous duty in air-handling units, cleanroom recirculation loops, data center cooling, industrial drying and new-energy process ventilation, and every unit is hipot tested and run-in before shipment. Quality management follows ISO 9001, and the product carries CE and RoHS declarations with CCC available for China.

Nominal Date
AC Backward Curved Centrifugal Fan image.png
Type FB3G560-4AAL-10
Model BLDCEC137

 

Nominal Voltage VAC 380
Voltage range VAC 304
Current draw A 2.7±10%
Speed(RPM) min-1  1450±5%
Power consumption W 1800±10%
Sound Pressure Level dB(A) 75±5%
Max. Air Flow CFM / m3 /H 7179.7/12200
Max. Static Pressure In.wg /Pa 3.24/810
Insulation class ~ Class B
Degree of protection ~ IP44
Control Input ~ 0~10VDC / PWM
Signal Output ~ FG (Tach output )
Connection diagram
image.png

Remarks:

Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized

Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel

Product drawing
image.png
Aerodynamic Performance Charts
image.png

Test condition:

Ⅰ.The test data is obtained under the specified environment conditions and installation mode

Ⅱ.Input Voltage---Operating voltage

Ⅲ.Temperature---Room temperature 25℃

Ⅴ.Humidity---65%RH

Safety Requirements

Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off

Ⅱ.Do not plug or unplug the fan lead plug when the fan is running

Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury

Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out

Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds

Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product

Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer

Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading

Advantages:

1. High Efficiency: The FB3G560-4AAL-10 delivers 12200 m3/h at 810 Pa while drawing only 1800W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.

2. Industrial-Grade Impeller: The 560mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.

3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).

4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.

5. Easy Installation and Maintenance: Compact 560mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.

FAQ

Q1:What kind of payments do you support?

A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping

Q2.Will you provide samples?

A2: Sample is available and can be delivered within 10days

Q3:How can I choose a more suitable model?

A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.

Q4:How can I place the order?

A4:  Usually quote you within 24 hours  after  we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.

Q5:About transportation

A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive. 

Q6:How long is the warranty period?

A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000