FB3G310-4AAS-30
| Nominal Voltage | VAC | 380 |
| Current draw | A | 2.9±10% |
| Speed(RPM) | min-1 | 2900±5% |
| Power consumption | W | 1100±10% |
| Max. Air Flow | CFM / m3 /H | 3112.6/5289 |
| Max. Static Pressure | In.wg /Pa | 4.8/1200 |
50pcs
When a single 310 mm impeller has to shoulder the work of an entire fan wall, the FB3G310-4AAS-30 is the answer. Delivering a maximum airflow of 5289 m3/h (3112.6 CFM) together with a peak static pressure of 1200 Pa (4.8 In.wg), this backward curved centrifugal fan lets HVAC designers collapse multi-fan arrays into one compact, serviceable module without surrendering pressure margin. Behind that performance sits a BLDCEC137 electronically commutated rotor: at 380VAC (operating window from 304V), it draws 2.9 A and converts 1100 W into air movement at 2900 RPM, so the unit belongs in the heavy-duty class rather than the commodity tier. The 310 mm impeller and matching die-cast aluminum endcap are both cast in aluminum alloy, a pairing that keeps rotating mass low, resists corrosion in humid air-handling cabinets, and holds blade geometry stable through continuous duty. Speed is commanded over the standard EC control interface, giving stepless modulation from a controller, a 0-10V signal or a building management system, which is exactly what variable-air-volume and demand-controlled filtration loops require. Insulation is Class F with thermal protection embedded in the winding, and the motor is built for long unattended runs; the ball bearing set is rated for tens of thousands of operating hours, and the 18AWG, 1000 mm factory cable simplifies field wiring. Typical installations include air-handling units, cleanroom and HEPA filtration banks, data-center cooling, industrial exhaust with long duct runs, and new-energy plant ventilation. CE and RoHS compliance and FANOVA's OEM/ODM engineering support round out the package.
The FB3G310-4AAS-30 is a backward curved centrifugal fan built around a 310 mm diameter impeller cast from aluminum alloy in a single piece. The backward-curved blade profile, with its characteristic swept trailing edge, is what allows this fan to generate both high volume and high pressure simultaneously: the blades discharge air radially at a shallow angle, so the airflow of 5289 m3/h and the static pressure ceiling of 1200 Pa are reached at 2900 RPM without the turbulence penalties that forward-curved wheels suffer at this duty point. Because the wheel and the endcap housing are both die-cast aluminum, the rotating assembly is dimensionally rigid, dimensionally stable under thermal cycling, and effectively immune to the moisture-driven corrosion that plagues painted steel impellers in air-handling cabinets. The rotor measures 137 mm and is directly coupled to the motor shaft, eliminating belt losses and alignment drift. The BLDCEC137 motor is an electronically commutated permanent-magnet design rated at 1100 W and 2.9 A on a 380VAC supply that tolerates a lower limit of 304V, so it rides through the voltage sag common on industrial distribution boards. Commutation is handled by an integrated drive that accepts a 0-10V or PWM speed command and reports status back to the host controller, enabling stepless modulation between a low-speed standby point and the full 2900 RPM rating; there is no separate VFD to wire, tune or house. Electrical protection includes Class F insulation and a thermally protected winding, and the motor is designed for continuous operation at the published duty point. The shaft runs in a matched pair of pre-lubricated ball bearings selected for tens of thousands of hours of service, with the bearing bores machined into the die-cast endcap to preserve concentricity over the fan's life. The factory-fitted cable is 18AWG, 1000 mm long, with clearly identified power and control conductors for straightforward termination in a control panel or terminal box. Mounting is via the cast aluminum flange, and the assembly is balanced at the factory to keep vibration within the limits expected of air-handling and filtration equipment. The fan is RoHS compliant and CE marked, and each unit is routine-tested for dielectric strength, insulation resistance, current draw and speed before shipment. FANOVA manufactures the FB3G310-4AAS-30 in its Suzhou plant under an ISO 9001 quality system and offers OEM/ODM customization of cable length, connector type, control protocol and nameplate branding for volume programs. Target applications include AHU supply and return sections, HEPA and cleanroom filter banks, telecom and data-center thermal management, process exhaust with long or restrictive ductwork, and ventilation of new-energy production lines.
| AC Backward Curved Centrifugal Fan | ![]() |
|
| Type | FB3G310-4AAS-30 | |
| Model | BLDCEC137 | |
| Nominal Voltage | VAC | 380 |
| Voltage range | VAC | 304 |
| Current draw | A | 2.9±10% |
| Speed(RPM) | min-1 | 2900±5% |
| Power consumption | W | 1100±10% |
| Sound Pressure Level | dB(A) | 84.8±5% |
| Max. Air Flow | CFM / m3 /H | 3112.6/5289 |
| Max. Static Pressure | In.wg /Pa | 4.8/1200 |
| Insulation class | ~ | Class B |
| Degree of protection | ~ | IP44 |
| Control Input | ~ | 0~10VDC / PWM |
| Signal Output | ~ | FG (Tach output ) |

Remarks:
Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized
Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel


Test condition:
Ⅰ.The test data is obtained under the specified environment conditions and installation mode
Ⅱ.Input Voltage---Operating voltage
Ⅲ.Temperature---Room temperature 25℃
Ⅴ.Humidity---65%RH
Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off
Ⅱ.Do not plug or unplug the fan lead plug when the fan is running
Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury
Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out
Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds
Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product
Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer
Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading
1. High Efficiency: The FB3G310-4AAS-30 delivers 5289 m3/h at 1200 Pa while drawing only 1100W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.
2. Industrial-Grade Impeller: The 310mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.
3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).
4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.
5. Easy Installation and Maintenance: Compact 310mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.
Q1:What kind of payments do you support?
A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping
Q2.Will you provide samples?
A2: Sample is available and can be delivered within 10days
Q3:How can I choose a more suitable model?
A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.
Q4:How can I place the order?
A4: Usually quote you within 24 hours after we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.
Q5:About transportation
A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive.
Q6:How long is the warranty period?
A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.