Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

FK3G175-48PL-70 DC Plug Fan 190mm 48V 620 m3/h

FK3G175-48PL-70

Nominal Voltage VDC 48
Current draw A 1.2±10%
Speed(RPM) min-1  2950±5%
Power consumption W 57.6±10%
Max. Air Flow CFM / m3 /H 364.87/620
Max. Static Pressure In.wg /Pa 1.97/492

50pcs

Brand:
FANOVA
Spu:
FK3G175-48PL-70
  • Overview
  • Recommended Products
Brief Description

When a cabinet needs a compact, chemically resistant blower that can sip power from a 48VDC bus, the FK3G175-48PL-70 plug fan delivers a lightweight, corrosion-tolerant alternative to metal impellers. Its 190 mm polypropylene impeller, reinforced with glass fiber, resists acids, bases and humid air while trimming rotating mass, so the BLDCDC72 brushless DC motor can spin it to 2950 RPM on just 57.6 W and 1.2 A. The result is a maximum airflow of 364.87 CFM (620 m3/h) and a static pressure ceiling of 1.97 in.wg (492 Pa) from a single compact plug-in module. Operating from a 36 to 57 VDC range, the fan is a natural fit for telecom -48VDC plants, battery-backed DC microgrids and off-grid solar cabinets where a safe extra-low voltage is preferred. Speed is commanded through a standard PWM input, and a tachometer output reports rotor speed to a DCIM or PLC for closed-loop monitoring. Motor windings are protected against overcurrent and locked-rotor conditions, the drive electronics are potted for vibration and moisture resistance, and insulation is rated for the low-voltage class appropriate to a 48VDC system. Dual ball bearings are specified for an L10 life of 70,000 hours at 40 degrees C, keeping maintenance intervals long in sealed enclosures. Typical installations include telecom equipment rooms, outdoor telecom cabinets, solar inverter housings, laboratory fume hoods and light industrial ventilation. The unit carries CE and RoHS declarations and is manufactured under ISO 9001 quality management.

Product Specification

The FK3G175-48PL-70 is a backward-curved centrifugal plug fan built around a 190 mm diameter impeller molded from glass-fiber-reinforced polypropylene. The material choice is deliberate: unlike painted steel, the composite wheel will not rust in condensing or salt-laden air, and it shrugs off the dilute acids and solvents often found in laboratory exhaust and battery-room ventilation. The backward-curved blade geometry, with a carefully tuned blade count and exit angle, converts the high rotational speed into pressure rather than turbulence, reaching 1.97 in.wg (492 Pa) at shutoff while still moving 364.87 CFM (620 m3/h) at free delivery. The wheel is dynamically balanced in two planes before assembly to keep vibration low at the 2950 RPM design point. A die-cast aluminum endcap and housing hold the bearing tube and motor stator rigidly, acting as a heat spreader for the drive electronics and giving the fan a flat, gasketed mounting face that drops into a square cutout on a cabinet wall or plenum panel. The rotor measures 72 mm in diameter, and the complete module weighs little enough for sheet-metal panels to carry without extra brackets. Inside, the BLDCDC72 motor is a three-phase brushless DC design with an integrated commutation board. It accepts any DC input from 36 to 57 VDC, so the same part number works on nominal 48 V telecom rectifiers, 48 V battery banks that swing high during equalize charge, and 42 to 54 V solar bus architectures. At the nominal 48 V point the fan draws 1.2 A and consumes 57.6 W, a figure low enough that a single 48 V rectifier module can feed a dozen fans without derating. Speed control is through a PWM input compatible with open-collector or push-pull drivers from a PLC, a DCIM controller or a thermostat board; a separate tachometer output provides two pulses per revolution for stall detection and airflow verification. The control leads are pulled up internally, so a disconnected PWM line defaults to full speed, a fail-safe behavior for cooling-critical cabinets. Electrical protection includes overcurrent limiting, locked-rotor shutdown with automatic restart, and reverse-polarity tolerance on the supply input. The 20 AWG cable, 500 mm long, carries the red and black supply pair plus the PWM and tach wires; it is rated for the 1.2 A operating current with margin and is jacketed for routing through cabinet interiors. The motor uses two pre-lubricated ball bearings selected for an L10 rating of 70,000 hours at 40 degrees C ambient, and the bearing tube is machined to a close tolerance so axial play stays controlled through thermal cycles. Acoustic output is held to 68 dB(A) at one meter, a level dominated by blade-passing tone and easily attenuated by a cabinet door or a short duct run. The fan meets CE and RoHS requirements and is built in an ISO 9001 certified facility, with each unit hipot tested and run-in before packing.

Nominal Date
DC Plug Fan image.png
Type FK3G175-48PL-70
Model BLDCDC72

 

Nominal Voltage VDC 48
Voltage range VDC 36~57
Current draw A 1.2±10%
Speed(RPM) min-1  2950±5%
Power consumption W 57.6±10%
Sound Pressure Level dB(A) 68±5%
Max. Air Flow CFM / m3 /H 364.87/620
Max. Static Pressure In.wg /Pa 1.97/492
Insulation class ~ Class B
Degree of protection ~ IP44
Control Input ~ 0~10VDC / PWM
Signal Output ~ FG (Tach output )
Connection diagram
image.png

Remarks:

Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized

Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel

Product drawing
image.png
Aerodynamic Performance Charts
image.png

Test condition:

Ⅰ.The test data is obtained under the specified environment conditions and installation mode

Ⅱ.Input Voltage---Operating voltage

Ⅲ.Temperature---Room temperature 25℃

Ⅴ.Humidity---65%RH

Safety Requirements

Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off

Ⅱ.Do not plug or unplug the fan lead plug when the fan is running

Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury

Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out

Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds

Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product

Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer

Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading

Advantages:

1. High Efficiency: The FK3G175-48PL-70 delivers 620 m3/h at 492 Pa while drawing only 57.6W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.

2. Industrial-Grade Impeller: The 190mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.

3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).

4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.

5. Easy Installation and Maintenance: Compact 190mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.

FAQ

Q1:What kind of payments do you support?

A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping

Q2.Will you provide samples?

A2: Sample is available and can be delivered within 10days

Q3:How can I choose a more suitable model?

A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.

Q4:How can I place the order?

A4:  Usually quote you within 24 hours  after  we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.

Q5:About transportation

A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive. 

Q6:How long is the warranty period?

A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000