Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

FB3G280-2AAL-30 EC Backward Curved Centrifugal Fan 280mm 230V 4650 m3/h

FB3G280-2AAL-30

Nominal Voltage VAC 230
Current draw A 4.8±10%
Speed(RPM) min-1  3500±5%
Power consumption W 1100±10%
Max. Air Flow CFM / m3 /H 2736.6/4650.2
Max. Static Pressure In.wg /Pa 5.4/1350

50pcs

Brand:
FANOVA
Spu:
FB3G280-2AAL-30
  • Overview
  • Recommended Products
Brief Description

When a single backward curved centrifugal fan has to do the work of a small parallel array, the FB3G280-2AAL-30 is built for that promotion. Its superpowers are raw volumetric delivery and genuine high-pressure capability at the same time: 4650.2 m3/h (2736.6 CFM) of free-air flow paired with 1350 Pa (5.4 In.wg) of maximum static pressure, so one 280 mm impeller can serve long duct runs, dense filter banks and multi-outlet plenums that would otherwise demand two or three smaller fans. The unit runs from 230VAC mains anywhere in the 184 to 270V band, drawing 4.8 A and 1100 W at 3500 RPM through a BLDCEC137 electronically commutated motor, which means the same fan accepts a direct AC feed with no external transformer or VFD and still offers continuous speed modulation through the onboard EC interface. The die-cast aluminum impeller and matching aluminum endcap and housing keep rotating mass low and heat rejection high, an important pairing in a 1.1 kW package. Protection and insulation follow FANOVA's EC platform standard, with locked-rotor, over-voltage and over-temperature safeguards plus Class F insulation and IP54-rated motor compartment for dusty plant rooms. Dual ball bearings rated for 40,000 hours at 40 degrees C ambient carry the shaft, and the 18AWG 1000 mm cable terminates in a sealed connector for straightforward field wiring. Typical duties include air-handling unit supply and return sections, cleanroom recirculation, heat-pump and chiller coil blowing, data-center CRAC retrofit, and industrial exhaust where a compact 280 mm frame must move serious air. The fan is CE and RoHS compliant and is produced under FANOVA's ISO 9001 quality system. For OEMs standardizing on one 230VAC EC platform, this model combines the airflow of a multi-fan bank with the pressure head of a dedicated high-static unit.

Product Specification

The FB3G280-2AAL-30 is a backward curved centrifugal fan built around a 280 mm diameter impeller die-cast in aluminum alloy. The backward-curved blade geometry, produced as a single homogeneous casting rather than a riveted assembly, gives the wheel high mechanical stiffness at 3500 RPM while keeping the blade surface smooth enough to limit boundary-layer losses along the trailing edge. The blade count and exit angle were selected to flatten the pressure-flow curve in the mid-band, which is why the fan still holds useful static pressure as flow climbs toward its 4650.2 m3/h ceiling rather than collapsing after free-air. The impeller is dynamically balanced after casting and is mounted directly on the motor shaft, so no belt, coupling or separate bearing housing is needed. The endcap and outer housing are also die-cast aluminum, providing a rigid, dimensionally stable scroll that resists distortion under duct loading and helps conduct motor heat away from the winding. The drive is a BLDCEC137 electronically commutated motor with a 137 mm rotor diameter, a design that trades a larger magnetic circumference for lower current density and cooler operation at the 1100 W rating. At 230VAC nominal the fan accepts any supply from 184 to 270V, 50 or 60 Hz, and draws 4.8 A maximum, giving designers headroom on branch circuits sized for 6 A protection. Speed is controlled through the EC motor's integrated power stage: a 0 to 10 VDC analog input, PWM input or onboard potentiometer header can command the full 3500 RPM range, and the motor reports tachometer and alarm outputs for BMS or DCIM integration. Soft-start ramps eliminate inrush surges, and the power factor correction stage keeps harmonic distortion low enough for multi-fan panels. Electrical protection covers locked rotor, over-current, over-voltage and over-temperature shutdown with automatic recovery, while the insulation system is Class F rated for a 155 degrees C hotspot and the motor compartment is sealed to IP54 against dust and splash. The shaft runs in two pre-lubricated ball bearings rated for 40,000 hours L10 life at 40 degrees C ambient; at lower plant-room temperatures the expected life extends further, and the bearings are field-replaceable in the service kit. The flying lead is 18AWG cable, 1000 mm long, with a sealed connector carrying mains, control and signal conductors. Acoustic output is 88 dB(A) at maximum speed, and because the EC motor holds speed independent of supply fluctuation, noise stays stable as the grid moves within the 184 to 270V window. The fan is CE marked, RoHS compliant and manufactured under FANOVA's ISO 9001 quality system, with routine hipot, insulation-resistance and balance checks on every unit.

Nominal Date
AC Backward Curved Centrifugal Fan image.png
Type FB3G280-2AAL-30
Model BLDCEC137

 

Nominal Voltage VAC 230
Voltage range VAC 184~270
Current draw A 4.8±10%
Speed(RPM) min-1  3500±5%
Power consumption W 1100±10%
Sound Pressure Level dB(A) 88±5%
Max. Air Flow CFM / m3 /H 2736.6/4650.2
Max. Static Pressure In.wg /Pa 5.4/1350
Insulation class ~ Class B
Degree of protection ~ IP44
Control Input ~ 0~10VDC / PWM
Signal Output ~ FG (Tach output )
Connection diagram
image.png

Remarks:

Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized

Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel

Product drawing
image.png
Aerodynamic Performance Charts
image.png

Test condition:

Ⅰ.The test data is obtained under the specified environment conditions and installation mode

Ⅱ.Input Voltage---Operating voltage

Ⅲ.Temperature---Room temperature 25℃

Ⅴ.Humidity---65%RH

Safety Requirements

Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off

Ⅱ.Do not plug or unplug the fan lead plug when the fan is running

Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury

Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out

Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds

Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product

Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer

Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading

Advantages:

1. High Efficiency: The FB3G280-2AAL-30 delivers 4650.2 m3/h at 1350 Pa while drawing only 1100W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.

2. Industrial-Grade Impeller: The 280mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.

3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).

4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.

5. Easy Installation and Maintenance: Compact 280mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.

FAQ

Q1:What kind of payments do you support?

A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping

Q2.Will you provide samples?

A2: Sample is available and can be delivered within 10days

Q3:How can I choose a more suitable model?

A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.

Q4:How can I place the order?

A4:  Usually quote you within 24 hours  after  we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.

Q5:About transportation

A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive. 

Q6:How long is the warranty period?

A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000