Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

FB3G220-48PL-92 DC Backward Curved Centrifugal Fan 220mm 48V 980 m3/h

FB3G220-48PL-92

Nominal Voltage VDC 48
Current draw A 1.65±10%
Speed(RPM) min-1  2760±5%
Power consumption W 80±10%
Max. Air Flow CFM / m3 /H 577.02/980.5
Max. Static Pressure In.wg /Pa 1.94/485

50pcs

Brand:
FANOVA
Spu:
FB3G220-48PL-92
  • Overview
  • Recommended Products
Brief Description

Where the FB3G220-48PL-92 earns its place is at the intersection of two pressures that telecom and DCIM engineers know well: the need to hang fans directly on a 48VDC plant without adding a conversion stage, and the need to keep the electrical bill and the battery drain as small as possible. This backward curved centrifugal fan draws 80 W at 1.65 A, spins a 220 mm impeller at 2760 RPM, and moves up to 577.02 CFM (980.5 m3H) against as much as 1.94 In.wg (485 Pa) of system resistance, so a single unit can shoulder the airflow duty that would otherwise need several smaller AC fans plus their transformers. The -48VDC input is the native language of telecom racks and DC power distribution: the fan accepts anything from 36 to 57VDC, rides through the float and equalize bands of a battery string, and reports its status to the DCIM layer through the BLDCDC92 drive's speed and alarm signals rather than through a separate monitoring module. Because the motor is electronically commutated, speed is set by a 0-10V analog line or a PWM input, giving the controls team a clean linear response from standstill to full 2760 RPM without the slip losses of an AC induction motor. The impeller is molded from glass-fiber reinforced propylene, which keeps the rotating mass low, resists the acids and solvents found in battery rooms, and costs far less than a machined aluminum wheel of the same diameter; the die-cast aluminum endcap and housing carry the heat out of the stator and hold the bearing seats rigid. Insulation is Class F with a Class B rise limit, the winding is protected against locked-rotor and over-temperature conditions, and the dual ball bearings are rated for 70,000 hours at 40 C so the fan can sit in an unattended cabinet for a decade of continuous duty. With 71.4 dB(A) at full speed and the ability to throttle back to whatever the thermal load actually requires, this model suits telecom cabinets, outdoor DC power shelters, energy-storage racks, EV charging enclosures, and inverter cooling, and it carries CE and RoHS compliance with UL-recognized components on request. For a design team that has been paying for AC-to-DC conversion on every fan, the FB3G220-48PL-92 removes that stage, that heat, and that failure point in one 80 W package.

Product Specification

The impeller of the FB3G220-48PL-92 is a 220 mm backward curved centrifugal wheel with a rotor diameter of 92 mm, injection molded in one piece from propylene compounded with glass fiber for a balance of stiffness, impact resistance, and dimensional stability under continuous rotation. The backward curved blade profile, with its swept trailing edges and gradual divergence toward the discharge, is what allows the wheel to build 1.94 In.wg (485 Pa) of static pressure without the flow separation that flat or forward curved blades suffer at high resistance, and the wheel is dynamically balanced after molding so that vibration stays low across the full 2760 RPM band. The glass-fiber loading raises the elastic modulus of the propylene enough that blade tips do not deflect measurably at top speed, while the plastic itself is unaffected by the humid, mildly acidic atmosphere of a battery room, unlike a coated steel wheel whose coating can chip at the weld lines. The die-cast aluminum endcap and housing form the structural spine of the fan: the endcap carries the front bearing seat and the motor mounting face, and its mass acts as a heat sink that draws stator losses away from the winding, while the housing's machined spigot and flange faces give a true mounting plane for ducted or plenum installations. The motor is a BLDCDC92 brushless DC design with an integrated commutation and drive stage, wound for a nominal 48VDC bus and tolerant of the full 36 to 57VDC range, so it can run from a telecom rectifier plant, a battery string under charge or discharge, or a regulated DC bus without any external converter. At the design point the fan consumes 80 W at 1.65 A and delivers 577.02 CFM (980.5 m3H) at free air, tapering along a stable pressure curve to 485 Pa at shutoff, which lets the same fan be specified for a low-resistance open-cabinet application and for a dense filter-and-duct arrangement simply by setting a different speed command. Speed control is through the drive's 0-10V analog input or a PWM duty-cycle signal, both referenced to the fan's own ground, with a tachometer output available for closed-loop verification and an alarm line for locked-rotor and over-temperature faults; the input impedance and filter constants are chosen so that a controller sharing a cabinet with switching inverters does not see false speed commands. Electrical connection is by a 500 mm flying lead of 20AWG cable, sized for the 1.65 A running current with margin for inrush and for the voltage drop of a long harness run, and the lead exits the housing through a strain-relieved grommet. The stator winding is Class F insulated and the design limits the temperature rise to Class B, which leaves thermal headroom for a 57VDC bus and a hot cabinet ambient; the drive board is conformally protected against humidity and dust. The shaft runs in two pre-lubricated ball bearings selected for an L10 life of 70,000 hours at 40 C, mounted in the aluminum endcap and housing so that bearing alignment is set by machined metal rather than by plastic, and the rotor is balanced as an assembly to keep bearing loads low. Acoustic output is 71.4 dB(A) at full speed, measured at the standard position, and falls roughly with the fifth power of speed as the fan is throttled, so a thermally controlled installation typically runs far below that figure. The fan is CE marked and RoHS compliant, with UL-recognized insulation system components available on request, and each unit is routine-tested for current draw, speed, and balance before packing.

Nominal Date
DC Backward Curved Centrifugal Fan image.png
Type FB3G220-48PL-92
Model BLDCDC92

 

Nominal Voltage VDC 48
Voltage range VDC 36~57
Current draw A 1.65±10%
Speed(RPM) min-1  2760±5%
Power consumption W 80±10%
Sound Pressure Level dB(A) 71.4±5%
Max. Air Flow CFM / m3 /H 577.02/980.5
Max. Static Pressure In.wg /Pa 1.94/485
Insulation class ~ Class B
Degree of protection ~ IP44
Control Input ~ 0~10VDC / PWM
Signal Output ~ FG (Tach output )
Connection diagram
image.png

Remarks:

Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized

Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel

Product drawing
image.png
Aerodynamic Performance Charts
image.png

Test condition:

Ⅰ.The test data is obtained under the specified environment conditions and installation mode

Ⅱ.Input Voltage---Operating voltage

Ⅲ.Temperature---Room temperature 25℃

Ⅴ.Humidity---65%RH

Safety Requirements

Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off

Ⅱ.Do not plug or unplug the fan lead plug when the fan is running

Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury

Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out

Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds

Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product

Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer

Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading

Advantages:

1. High Efficiency: The FB3G220-48PL-92 delivers 980.5 m3/h at 485 Pa while drawing only 80W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.

2. Industrial-Grade Impeller: The 220mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.

3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).

4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.

5. Easy Installation and Maintenance: Compact 220mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.

FAQ

Q1:What kind of payments do you support?

A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping

Q2.Will you provide samples?

A2: Sample is available and can be delivered within 10days

Q3:How can I choose a more suitable model?

A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.

Q4:How can I place the order?

A4:  Usually quote you within 24 hours  after  we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.

Q5:About transportation

A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive. 

Q6:How long is the warranty period?

A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000