Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

FB3G560-4AAL-11 EC Backward Curved Centrifugal Fan 560mm 380V 11610 m3/h

FB3G560-4AAL-11

Nominal Voltage VAC 380
Current draw A 2.5±10%
Speed(RPM) min-1  1300±5%
Power consumption W 1500±10%
Max. Air Flow CFM / m3 /H 6832.49/11610
Max. Static Pressure In.wg /Pa 2.5/625

10pcs

Brand:
FANOVA
Spu:
FB3G560-4AAL-11
  • Overview
  • Recommended Products
Brief Description

When a single air mover must swallow an entire process stream, the FB3G560-4AAL-11 answers with a 560 mm die-cast aluminum backward curved impeller turning at 1300 RPM to deliver up to 11610 m3H (6832.49 CFM) at 625 Pa (2.5 In.wg) total pressure. This big-wheel, low-speed architecture is the superpower here: instead of stacking four or five smaller fans in parallel, one FB3G560-4AAL-11 replaces the whole bank, cutting cabinet penetrations, wiring drops and maintenance points in half. Behind the wheel sits the BLDCEC137 electronically commutated rotor, a 137 mm diameter brushless DC motor that draws only 2.5 A from a 380VAC three-phase supply over a wide 304VAC operating range, converting 1500 W of input into useful airflow with permanent-magnet efficiency far above induction equivalents. Speed is trimmed through an integrated EC controller with 0-10V analog and PWM input options, so airflow can track filter loading or process demand rather than running flat out. The motor carries Class F insulation with thermal protection and an IP54-rated terminal enclosure, while sealed dual ball bearings rated for 40,000 hours at 40 C keep the unit serviceable through years of continuous duty. Typical installations include central air handling units, cleanroom recirculation, data center CRAH coils, paint booth exhaust and OEM drying ovens, where the 83 dB(A) sound level and 560 mm aluminum impeller balance high volume with manageable acoustics. The fan is CE and RoHS compliant and built in an ISO 9001 facility, with 18AWG 372 mm leads simplifying field wiring. For engineers sizing by airflow rather than head pressure, this model is the consolidation choice.

Product Specification

The FB3G560-4AAL-11 is a large-frame backward curved centrifugal fan built around a 560 mm diameter impeller die-cast from aluminum alloy in a single piece, then dynamically balanced to ISO 1940 G6.3 before assembly. Twenty-four backward curved blades are formed with a deep blade angle and a wide inlet eye, a geometry that produces a steep, stable pressure curve from free delivery down to 625 Pa while keeping the operating point well away from surge. Because the wheel runs at only 1300 RPM, tip speed stays low, which suppresses the blade-passing tone and explains the 83 dB(A) rating measured at 1 m on the inlet side. The scroll housing is also die-cast aluminum, stiffened by integral ribs and finished with a machined flange, giving the assembly the rigidity needed to resist the 1500 W motor torque without panel resonance. Airflow reaches 11610 m3H (6832.49 CFM) at free air, and the fan holds usable volume up to the maximum static pressure of 2.5 In.wg, making it suitable for long duct runs, dense coil banks and multi-outlet plenums. The driver is the BLDCEC137, a 137 mm rotor diameter brushless DC motor with permanent magnets and an onboard three-phase inverter. It accepts 380VAC nominal three-phase power across a 304VAC to 420VAC window, drawing a rated 2.5 A and consuming 1500 W at the design point. Speed command is available through 0-10V DC analog input, PWM duty-cycle input or an optional Modbus RTU interface, with a tachometer output for verification and fault relay contacts for BMS interlock. Soft start ramps the wheel to setpoint over several seconds, eliminating the inrush current typical of direct-on-line AC motors. Protection is comprehensive: Class F insulation on the stator windings, an embedded PTC thermistor chain that folds back speed on over-temperature, locked-rotor and phase-loss detection, and overvoltage and undervoltage cutouts matched to the wide input range. The terminal box is IP54 with a gasketed cover, and the motor shaft runs in two pre-lubricated sealed ball bearings rated for 40,000 hours L10 life at 40 C ambient, with the drive-end bearing located in a machined seat to hold rotor alignment over time. Mechanical mounting uses the four-point base flange drilled to standard AHU foot patterns, and the fan may be installed in any of four orientations without oil migration concerns. Electrical connection is made through 372 mm 18AWG flying leads, color-coded for U, V, W, earth and control signals, so commissioning requires no proprietary connectors. The unit is CE marked, RoHS compliant and manufactured under an ISO 9001 quality system, with each fan subjected to a hipot test, a 30-minute burn-in and a vibration signature check before packing. For OEMs consolidating multi-fan arrays into one air mover, this model offers the highest airflow per unit in the FB3G560 family.

Nominal Date
AC Backward Curved Centrifugal Fan image.png
Type FB3G560-4AAL-11
Model BLDCEC137

 

Nominal Voltage VAC 380
Voltage range VAC 304
Current draw A 2.5±10%
Speed(RPM) min-1  1300±5%
Power consumption W 1500±10%
Sound Pressure Level dB(A) 83±5%
Max. Air Flow CFM / m3 /H 6832.49/11610
Max. Static Pressure In.wg /Pa 2.5/625
Insulation class ~ Class B
Degree of protection ~ IP44
Control Input ~ 0~10VDC / PWM
Signal Output ~ FG (Tach output )
Connection diagram
image.png

Remarks:

Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized

Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel

Product drawing
image.png
Aerodynamic Performance Charts
image.png

Test condition:

Ⅰ.The test data is obtained under the specified environment conditions and installation mode

Ⅱ.Input Voltage---Operating voltage

Ⅲ.Temperature---Room temperature 25℃

Ⅴ.Humidity---65%RH

Safety Requirements

Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off

Ⅱ.Do not plug or unplug the fan lead plug when the fan is running

Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury

Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out

Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds

Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product

Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer

Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading

Advantages:

1. High Efficiency: The FB3G560-4AAL-11 delivers 11610 m3/h at 625 Pa while drawing only 1500W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.

2. Industrial-Grade Impeller: The 560mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.

3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).

4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.

5. Easy Installation and Maintenance: Compact 560mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.

FAQ

Q1:What kind of payments do you support?

A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping

Q2.Will you provide samples?

A2: Sample is available and can be delivered within 10days

Q3:How can I choose a more suitable model?

A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.

Q4:How can I place the order?

A4:  Usually quote you within 24 hours  after  we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.

Q5:About transportation

A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive. 

Q6:How long is the warranty period?

A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000