FB3G190-2APL-90
| Nominal Voltage | VAC | 230 |
| Current draw | A | 1.1±10% |
| Speed(RPM) | min-1 | 4000±5% |
| Power consumption | W | 150±10% |
| Max. Air Flow | CFM / m3 /H | 505.2/858.4 |
| Max. Static Pressure | In.wg /Pa | 3.08/771 |
50pcs
When ductwork is long, filters are dense and every pascal of pressure counts, the FB3G190-2APL-90 answers with 771 Pa of maximum static pressure from a compact 190 mm backward curved impeller. This 230VAC electronically commutated fan replaces a conventional AC centrifugal blower without any step-down transformer: the wide 184 to 277VAC input accepts nominal 230V mains plus normal utility sag and surge, so the same unit ships to European, Asian and 240V markets. At 4000 RPM the BLDCEC92 motor delivers 150 W while moving up to 858.4 m3/h (505.2 CFM), drawing only 1.1 A - a combination that lets one high-pressure fan do the work of two lower-pressure units in series. Pressure is the headline here: the glass-fiber reinforced propylene impeller is molded with a backward curved blade profile optimized for high pressure rise, giving the fan the headroom to push air through HEPA-grade media, long exhaust runs, silencers and multi-outlet manifolds. Speed is fully controllable through the integrated EC electronics, so airflow can be trimmed on site to match the actual system resistance rather than throttled with a damper. The motor winding is protected against over-temperature and locked-rotor conditions, insulation is Class F, and the die-cast aluminum endcap carries heat away from the electronics for stable continuous duty. Bearings are long-life ball type rated for tens of thousands of hours at moderate ambient, keeping maintenance intervals long in air-handling cabinets and cleanroom plenums. Typical installations include laboratory fume extraction, commercial ventilation with high-efficiency filtration, air purifiers, heat recovery units and industrial process cooling. The fan carries CE and RoHS compliance and is built in an ISO 9001 facility.
The FB3G190-2APL-90 is a backward curved centrifugal fan built around a 190 mm diameter impeller injection-molded from glass-fiber reinforced propylene. The impeller uses a multi-blade backward curved geometry in which the blade exit angle is set to convert high tangential velocity into static pressure rather than pure volume, which is why the model reaches 771 Pa at shutoff condition while still delivering 858.4 m3/h at free air. The hub and blade root are thickened and the glass-fiber loading raises the elastic modulus of the propylene so the wheel holds its shape at 4000 RPM without flutter, a critical property for a pressure-optimized wheel where blade deflection would erode both efficiency and acoustic quality. The wheel is dynamically balanced after molding to keep vibration low across the speed range. The impeller is enclosed by a die-cast aluminum endcap and mounting flange; aluminum was selected over steel for its dimensional stability, corrosion resistance and its ability to conduct heat away from the motor and control board, which extends the service life of the electronics in enclosed air-handling cabinets. The rotor diameter is 92 mm, matched to the BLDCEC92 three-phase electronically commutated motor. This motor uses permanent magnets on the rotor and a stator wound for sinusoidal commutation, driven by an integrated inverter that rectifies the incoming AC and synthesizes a variable-frequency three-phase waveform. Because speed is set electronically, the fan delivers a nearly flat efficiency curve across a wide flow range and avoids the slip losses of an induction motor. Input is 230VAC nominal with full operation from 184 to 277VAC at 50 or 60 Hz; current draw is 1.1 A and input power 150 W at the rated operating point, with active power factor correction keeping the power factor close to unity so the fan presents a light reactive load to the supply. Speed control is via a 0 to 10 VDC analog signal or PWM input on the control leads, with tachometer output for monitoring; the fan can also be operated at fixed speed by leaving the control input at its default. Electrical connection is made through a 500 mm flying lead of 20AWG cable, with clearly identified live, neutral, control and tachometer conductors. Protection features include locked-rotor shutdown, over-current limiting and thermal protection of the winding; insulation is Class F with a dielectric strength tested to standard requirements. The shaft runs in long-life ball bearings selected for horizontal or vertical mounting and rated for extended L10 life at the rated speed and moderate ambient temperatures, with the bearing system preloaded to suppress axial play and reduce noise. Acoustic output is 74 dB(A) at full speed, measured at one meter in free field; the backward curved blade design and the rigid aluminum housing keep tonal content low so the sound is broadband rather than whining. The unit is CE marked, RoHS compliant and manufactured under an ISO 9001 quality system, with each fan run-tested for speed, current and balance before packing.
| AC Backward Curved Centrifugal Fan | ![]() |
|
| Type | FB3G190-2APL-90 | |
| Model | BLDCEC92 | |
| Nominal Voltage | VAC | 230 |
| Voltage range | VAC | 184~277 |
| Current draw | A | 1.1±10% |
| Speed(RPM) | min-1 | 4000±5% |
| Power consumption | W | 150±10% |
| Sound Pressure Level | dB(A) | 74±5% |
| Max. Air Flow | CFM / m3 /H | 505.2/858.4 |
| Max. Static Pressure | In.wg /Pa | 3.08/771 |
| Insulation class | ~ | Class B |
| Degree of protection | ~ | IP44 |
| Control Input | ~ | 0~10VDC / PWM |
| Signal Output | ~ | FG (Tach output ) |

Remarks:
Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized
Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel


Test condition:
Ⅰ.The test data is obtained under the specified environment conditions and installation mode
Ⅱ.Input Voltage---Operating voltage
Ⅲ.Temperature---Room temperature 25℃
Ⅴ.Humidity---65%RH
Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off
Ⅱ.Do not plug or unplug the fan lead plug when the fan is running
Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury
Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out
Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds
Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product
Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer
Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading
1. High Efficiency: The FB3G190-2APL-90 delivers 858.4 m3/h at 771 Pa while drawing only 150W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.
2. Industrial-Grade Impeller: The 190mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.
3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).
4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.
5. Easy Installation and Maintenance: Compact 190mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.
Q1:What kind of payments do you support?
A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping
Q2.Will you provide samples?
A2: Sample is available and can be delivered within 10days
Q3:How can I choose a more suitable model?
A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.
Q4:How can I place the order?
A4: Usually quote you within 24 hours after we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.
Q5:About transportation
A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive.
Q6:How long is the warranty period?
A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.