FB3G133-48PL-72
| Nominal Voltage | VDC | 48 |
| Current draw | A | 0.65±10% |
| Speed(RPM) | min-1 | 3900±5% |
| Power consumption | W | 31.2±10% |
| Max. Air Flow | CFM / m3 /H | 268.7/456.6 |
| Max. Static Pressure | In.wg /Pa | 1.52/380 |
50pcs
Think of the FB3G133-48PL-72 as the quiet specialist of the FANOVA backward curved centrifugal family: a 133 mm impeller running on a 48VDC nominal supply (usable from 36 to 57VDC) that keeps acoustic output at just 64 dB(A) while drawing a mere 0.65 A and 31.2 W. That combination of near-conversation-level noise and sub-35 W consumption makes it a natural fit for telecom cabinets, DCIM-managed equipment rooms, laboratory instrument bays and office-adjacent air handling where fan noise is heard by people, not just measured by meters. The impeller is molded from glass-fiber reinforced propylene, giving a light rotating mass that spools up smoothly with low vibration and shrugs off many common chemical and humidity exposures, while the die-cast aluminum endcap holds bearing alignment and dissipates motor heat. Drive comes from a BLDCDC72 brushless DC motor with integrated electronic commutation, so speed is controlled electronically through the DC input rather than by voltage-dropping or external drives; PWM and tach feedback options make it straightforward to integrate with building controllers and telecom power systems. Insulation and protection are built for continuous duty, and the bearing system is rated for long L10 life at 3900 RPM. A 20AWG, 500 mm lead-out cable simplifies wiring inside dense enclosures. Typical applications include telecom -48VDC racks, heat exchangers, inverter cooling, air purifiers, medical and lab ventilation and compact AHUs, and the unit is produced under ISO 9001 with CE and RoHS compliance for global shipment.
The FB3G133-48PL-72 is a single-inlet backward curved centrifugal fan built around a 133 mm diameter impeller. The wheel is injection molded from glass-fiber reinforced propylene, a material chosen for its favorable stiffness-to-weight ratio: the blades hold their backward-curved geometry under centrifugal load while the low mass keeps rotor inertia down, which shortens spin-up time and reduces start-up current. Backward curved blade geometry produces a rising pressure characteristic that resists stall in the medium-flow region, giving the fan a stable operating band rather than a sharply peaked curve. At free delivery the fan moves 268.7 CFM (456.6 m3/h); at shutoff it develops 1.52 in.wg (380 Pa). The impeller is dynamically balanced before assembly to control once-per-revolution vibration, which is the main source of tonal noise in compact centrifugal fans and the reason the unit holds 64 dB(A).
Rotation is provided by a BLDCDC72 brushless DC motor with a 72 mm rotor diameter. Commutation is handled by integrated electronics, eliminating brushes and the associated wear debris and electrical noise. The motor is wound for a 48VDC nominal bus with an operating window of 36 to 57VDC, covering the tolerance band of telecom -48VDC plants and 48V battery systems without additional regulation. At 3900 RPM the fan draws 0.65 A and 31.2 W, a low figure for the airflow delivered, which keeps thermal load on upstream power supplies small and extends backup battery runtime in DC-powered installations. Speed is set electronically: the standard interface accepts a DC control signal, with PWM control and tachometer output available as configuration options so the fan can report speed to a DCIM or BMS platform and be modulated on demand rather than run at full speed continuously.
Mechanically, the impeller is carried in a die-cast aluminum endcap that provides a rigid, dimensionally stable seat for the bearing system and acts as a heat spreader for the motor electronics. Bearings are selected for continuous duty at 3900 RPM and rated for long L10 life under the rated load and temperature; the vertical or horizontal mounting attitude should follow the installation drawing to preserve the calculated life. Electrical connection is via a 20AWG cable with a 500 mm free length, adequate for reaching terminal blocks inside rack enclosures and control cabinets; the lead-out is strain-relieved at the motor exit. Insulation is designed for the low-voltage DC class with reinforced separation between the winding and the electronics, and the fan is intended for continuous operation across the rated ambient range.
Quality control covers impeller balance, hipot and insulation resistance on the motor circuit, a full-speed run-in with current and acoustic checks, and a final curve verification against the published airflow and pressure points. The FB3G133-48PL-72 is manufactured in an ISO 9001 facility and carries CE and RoHS declarations. Target applications include telecom -48VDC cabinet cooling, DCIM-monitored equipment rooms, heat exchanger and inverter cooling, air purification, laboratory and medical ventilation and compact air handling units where low noise, low power and a 48V DC bus are all required.
| DC Backward Curved Centrifugal Fan | ![]() |
|
| Type | FB3G133-48PL-72 | |
| Model | BLDCDC72 | |
| Nominal Voltage | VDC | 48 |
| Voltage range | VDC | 36~57 |
| Current draw | A | 0.65±10% |
| Speed(RPM) | min-1 | 3900±5% |
| Power consumption | W | 31.2±10% |
| Sound Pressure Level | dB(A) | 64±5% |
| Max. Air Flow | CFM / m3 /H | 268.7/456.6 |
| Max. Static Pressure | In.wg /Pa | 1.52/380 |
| Insulation class | ~ | Class B |
| Degree of protection | ~ | IP44 |
| Control Input | ~ | 0~10VDC / PWM |
| Signal Output | ~ | FG (Tach output ) |

Remarks:
Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized
Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel


Test condition:
Ⅰ.The test data is obtained under the specified environment conditions and installation mode
Ⅱ.Input Voltage---Operating voltage
Ⅲ.Temperature---Room temperature 25℃
Ⅴ.Humidity---65%RH
Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off
Ⅱ.Do not plug or unplug the fan lead plug when the fan is running
Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury
Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out
Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds
Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product
Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer
Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading
1. High Efficiency: The FB3G133-48PL-72 delivers 456.6 m3/h at 380 Pa while drawing only 31.2W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.
2. Industrial-Grade Impeller: The 133mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.
3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).
4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.
5. Easy Installation and Maintenance: Compact 133mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.
Q1:What kind of payments do you support?
A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping
Q2.Will you provide samples?
A2: Sample is available and can be delivered within 10days
Q3:How can I choose a more suitable model?
A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.
Q4:How can I place the order?
A4: Usually quote you within 24 hours after we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.
Q5:About transportation
A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive.
Q6:How long is the warranty period?
A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.