FK3G175-48LH-7N
| Nominal Voltage | VDC | 48 |
| Current draw | A | 1.85±10% |
| Speed(RPM) | min-1 | 3900±5% |
| Power consumption | W | 88±10% |
| Max. Air Flow | CFM / m3 /H | 403.7/686 |
| Max. Static Pressure | In.wg /Pa | 2.47/617 |
50pcs
The FK3G175-48LH-7N is a 48VDC backward-curved plug fan engineered for the telecom and DC power ecosystem, where a nominal -48VDC bus is already present and every watt of conversion loss is money spent twice. Running from a 36 to 57VDC input window, it draws just 1.85 A and 88 W while delivering up to 403.7 CFM (686 m3H) of airflow against 2.47 in.wg (617 Pa) of static pressure at 3900 RPM. Because the 175 mm impeller is molded from glass-fiber reinforced propylene, the rotating mass stays low, so the BLDCDC72 brushless DC motor spins up quickly and coasts down without the shaft stress that heavier metal wheels impose on repeated start-stop duty cycles. Speed is commanded over a 0-10VDC analog interface with PWM and FG tach feedback available, letting a DCIM or rack controller modulate the fan continuously rather than switching it on and off. Insulation is Class B, the die-cast aluminum endcap carries the motor heat away and doubles as the mounting structure, and the ball-bearing set is rated for 40,000 hours at 40 degrees C so the unit can match a ten-year telecom service life. Typical installations are 48V rack cooling, outdoor telecom cabinets, battery thermal management, LED and power-electronics enclosures, and off-grid or solar-assisted ventilation where no AC mains exist. The fan is CE and RoHS compliant and is built in an ISO 9001 factory, with a 20AWG 500 mm lead supplied as standard.
The FK3G175-48LH-7N belongs to FANOVA's 175 mm backward-curved plug fan family, a platform defined by a single-piece die-cast aluminum endcap that carries the motor, the mounting flange and the aerodynamic inlet in one rigid part. The impeller is a 175 mm diameter wheel molded in glass-fiber reinforced propylene; the fiber loading raises the elastic modulus of the blade roots so the forward-leaning backward-curved blades hold their profile at 3900 RPM without visible deflection, while the polymer surface resists the acidic and solvent-laden airstreams common in battery rooms and outdoor cabinets. The rotor is a 72 mm brushless DC unit, model BLDCDC72, driven by integrated commutation electronics that accept any supply from 36 to 57VDC, making the fan directly compatible with the -48VDC nominal plant used in telecommunications central offices and data centers. At rated 48VDC the fan consumes 1.85 A and 88 W; the low current draw means a single 10 A branch feed can support several fans in parallel without conductor upsizing, and the 88 W figure sits comfortably inside the DCIM power budget of a standard equipment rack. Aerodynamic output is 403.7 CFM (686 m3H) free delivery and 2.47 in.wg (617 Pa) shut-off, with the operating point typically chosen between 250 and 350 CFM where efficiency peaks. Acoustic emission is 66 dB(A) at one meter, a level dominated by blade passing frequency and easily attenuated by the cabinet's own acoustic lining. Control is through a 0-10VDC analog input, with PWM duty control and an open-collector FG tachometer output offered as options; the control leads and the 20AWG, 500 mm power cable exit the endcap through a strain-relieved grommet. Motor insulation is Class B, the winding is vacuum-impregnated, and the drive board is conformally coated for humidity tolerance. The shaft runs in a preloaded ball-bearing pair lubricated for life and rated 40,000 hours at 40 degrees C ambient, with the aluminum endcap acting as the heat sink that keeps bearing temperature well below the grease limit. The fan is polarity-protected, locked-rotor protected and capable of repeated start-stop cycling without inrush stress. It is CE marked, RoHS compliant, and manufactured under ISO 9001 quality management with 100 percent run-in testing before packing.
| DC Plug Fan | ![]() |
|
| Type | FK3G175-48LH-7N | |
| Model | BLDCDC72 | |
| Nominal Voltage | VDC | 48 |
| Voltage range | VDC | 36~57 |
| Current draw | A | 1.85±10% |
| Speed(RPM) | min-1 | 3900±5% |
| Power consumption | W | 88±10% |
| Sound Pressure Level | dB(A) | 66±5% |
| Max. Air Flow | CFM / m3 /H | 403.7/686 |
| Max. Static Pressure | In.wg /Pa | 2.47/617 |
| Insulation class | ~ | Class B |
| Degree of protection | ~ | IP44 |
| Control Input | ~ | 0~10VDC / PWM |
| Signal Output | ~ | FG (Tach output ) |

Remarks:
Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized
Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel


Test condition:
Ⅰ.The test data is obtained under the specified environment conditions and installation mode
Ⅱ.Input Voltage---Operating voltage
Ⅲ.Temperature---Room temperature 25℃
Ⅴ.Humidity---65%RH
Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off
Ⅱ.Do not plug or unplug the fan lead plug when the fan is running
Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury
Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out
Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds
Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product
Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer
Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading
1. High Efficiency: The FK3G175-48LH-7N delivers 686 m3/h at 617 Pa while drawing only 88W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.
2. Industrial-Grade Impeller: The 175mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.
3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).
4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.
5. Easy Installation and Maintenance: Compact 175mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.
Q1:What kind of payments do you support?
A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping
Q2.Will you provide samples?
A2: Sample is available and can be delivered within 10days
Q3:How can I choose a more suitable model?
A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.
Q4:How can I place the order?
A4: Usually quote you within 24 hours after we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.
Q5:About transportation
A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive.
Q6:How long is the warranty period?
A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.