FK3G175-24PL-70
| Nominal Voltage | VDC | 24 |
| Current draw | A | 2.4±10% |
| Speed(RPM) | min-1 | 2950±5% |
| Power consumption | W | 57.6±10% |
| Max. Air Flow | CFM / m3 /H | 364.87/620 |
| Max. Static Pressure | In.wg /Pa | 1.97/492 |
50pcs
When a 24 VDC power budget is tight and reliability is non-negotiable, the FK3G175-24PL-70 plug fan delivers 620 m3/h (364.87 CFM) of airflow while drawing only 57.6 W — a figure that lets solar-charged battery banks, telecom cabinets and off-grid ventilation systems run longer between charges. Its glass-fiber reinforced polypropylene impeller measures 190 mm and is driven by a BLDCDC72 brushless DC motor, combining low rotating mass with chemical resistance and a corrosion-free structure that never needs painting. The fan accepts a wide 16–28 VDC input, so it rides through the voltage sag of a discharging lead-acid or lithium pack without stalling, and speed is commanded through a 0–10 V analog signal or PWM input for precise airflow trimming. At 2950 RPM the unit produces up to 492 Pa (1.97 in. wg) of static pressure, enough to push air through a coalescing filter or a short duct run in a remote equipment shelter. The die-cast aluminum endcap and housing act as a rigid mounting frame and heat spreader, keeping the motor cool in sealed enclosures where ambient temperatures climb. Insulation is Class F with electronic protection against locked rotor, over-current and reverse polarity, and the dual ball-bearing system is rated for 70,000 hours at 40 degrees C, translating to roughly eight years of continuous duty. A 500 mm, 20 AWG cable exits the housing for direct connection to a controller or terminal block. Typical applications include solar-powered telecom huts, battery energy storage cabinets, marine and RV ventilation, kiosk cooling and laboratory exhaust where low voltage is mandatory. The fan carries CE and RoHS marks and is manufactured under ISO 9001 in FANOVA's Suzhou plant, with optional tach output and IP54 protection available on request.
The FK3G175-24PL-70 belongs to FANOVA's backward-curved centrifugal plug fan family and is built around a 190 mm impeller molded from polypropylene reinforced with glass fiber. That material choice is deliberate: the composite resists dilute acids, cleaning agents and salt-laden air, weighs roughly half as much as an equivalent steel wheel, and holds blade geometry accurately through the injection-molding process, which keeps aerodynamic balance consistent from unit to unit. The impeller uses a backward-curved blade profile with a high blade count to generate pressure smoothly and reduce tonal noise at the 2950 RPM design point. Each wheel is dynamically balanced before assembly, and the completed rotor spins inside a die-cast aluminum endcap that serves as the motor housing, bearing carrier and mounting interface. The aluminum casting dissipates heat from the motor windings and provides a flat, dimensionally stable face for bolting into an air handler panel or enclosure wall. The BLDCDC72 motor is a 72 mm rotor diameter brushless DC design with integrated commutation electronics. It operates from a 16 to 28 VDC supply, nominally 24 VDC, and draws 2.4 A at full speed for a power input of 57.6 W. Speed control is achieved through a 0 to 10 V analog input or a PWM signal, and the controller includes soft-start ramping to limit inrush current when the fan is switched on from a battery source. Electrical protection covers locked-rotor shutdown, over-current limiting, under-voltage lockout and reverse-polarity tolerance, preventing damage during field wiring mistakes. The motor is insulated to Class F standards and the winding is impregnated to resist vibration and moisture. Bearings are pre-lubricated dual ball bearings rated for 70,000 hours of operation at 40 degrees C ambient, with a temperature range of -20 to +60 degrees C for the standard version. The connection cable is 500 mm long, 20 AWG, with flying leads for direct termination. Acoustic output is 68 dB(A) at one meter, measured at rated voltage and free-air inlet, and the fan delivers a maximum static pressure of 492 Pa (1.97 in. wg) at shutoff with a maximum free airflow of 620 m3/h (364.87 CFM). The die-cast aluminum housing includes four mounting bosses and can be oriented in any plane. CE and RoHS compliance are standard, and the product is manufactured in an ISO 9001 certified facility with 100 percent end-of-line run testing. For solar, telecom and off-grid applications, the wide input window and low power draw make the FK3G175-24PL-70 a practical choice where a 24 V bus must support multiple loads without excessive drain.
| DC Plug Fan | ![]() |
|
| Type | FK3G175-24PL-70 | |
| Model | BLDCDC72 | |
| Nominal Voltage | VDC | 24 |
| Voltage range | VDC | 16~28 |
| Current draw | A | 2.4±10% |
| Speed(RPM) | min-1 | 2950±5% |
| Power consumption | W | 57.6±10% |
| Sound Pressure Level | dB(A) | 68±5% |
| Max. Air Flow | CFM / m3 /H | 364.87/620 |
| Max. Static Pressure | In.wg /Pa | 1.97/492 |
| Insulation class | ~ | Class B |
| Degree of protection | ~ | IP44 |
| Control Input | ~ | 0~10VDC / PWM |
| Signal Output | ~ | FG (Tach output ) |

Remarks:
Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized
Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel


Test condition:
Ⅰ.The test data is obtained under the specified environment conditions and installation mode
Ⅱ.Input Voltage---Operating voltage
Ⅲ.Temperature---Room temperature 25℃
Ⅴ.Humidity---65%RH
Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off
Ⅱ.Do not plug or unplug the fan lead plug when the fan is running
Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury
Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out
Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds
Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product
Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer
Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading
1. High Efficiency: The FK3G175-24PL-70 delivers 620 m3/h at 492 Pa while drawing only 57.6W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.
2. Industrial-Grade Impeller: The 190mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.
3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).
4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.
5. Easy Installation and Maintenance: Compact 190mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.
Q1:What kind of payments do you support?
A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping
Q2.Will you provide samples?
A2: Sample is available and can be delivered within 10days
Q3:How can I choose a more suitable model?
A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.
Q4:How can I place the order?
A4: Usually quote you within 24 hours after we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.
Q5:About transportation
A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive.
Q6:How long is the warranty period?
A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.