FK3G175-24LH-7F
| Nominal Voltage | VDC | 24 |
| Current draw | A | 4.0±10% |
| Speed(RPM) | min-1 | 4250±5% |
| Power consumption | W | 96±10% |
| Max. Air Flow | CFM / m3 /H | 939.4/798.1 |
| Max. Static Pressure | In.wg /Pa | 2.93/731 |
50pcs
When a 24 VDC power source must drive a backward-curved centrifugal impeller against a 731 Pa system resistance while drawing less than 100 W, the FK3G175-24LH-7F is the plug-fan module engineered for that exact intersection of high static pressure and ultra-low power. Its 175 mm glass-fiber reinforced propylene impeller and 72 mm rotor BLDCDC72 brushless DC motor deliver 939.4 CFM (798.1 m3/h) at free air and 2.93 In.wg (731 Pa) maximum static pressure, using only 96 W at 4.0 A from a 16-28 VDC supply. Unlike line-voltage fans that need a transformer or inverter stage, this model accepts DC directly, so it is suited to solar-battery, off-grid, telecom cabinet and battery-energy-storage ventilation where safety extra-low voltage and minimal parasitic load matter. Speed is set electronically across the full 4250 RPM range, giving installers a clean way to match airflow to filter loading without damper losses. The motor carries Class F insulation and is protected against locked-rotor and over-current conditions, while the die-cast aluminum endcap and housing provide a rigid, corrosion-resistant frame that also acts as a heat sink for the drive electronics. Rated bearing life of 70,000 hours at 40 C supports continuous duty in air-handling units, laboratory fume hoods, cleanroom fan-filter units and EV charging enclosures. The unit is CE and RoHS compliant and is manufactured under FANOVA's ISO 9001 quality system in Suzhou, China, with OEM/ODM customization available for cable length, connector type and control interface.
The FK3G175-24LH-7F is a backward-curved centrifugal plug fan built around a 175 mm diameter impeller molded from glass-fiber reinforced propylene. The composite impeller uses a hub-and-shroud construction with a backward-curved blade set selected to trade peak airflow for pressure stability: at free delivery the fan moves 939.4 CFM (798.1 m3/h), and it continues to 2.93 In.wg (731 Pa) at shutoff, a pressure ratio that lets a single compact module serve long duct runs, dense filter banks or multi-outlet plenums that would otherwise require two smaller fans in series. Because the blades are backward-curved, the power curve stays flat toward free air, so the 96 W nominal input does not climb steeply if the system resistance falls; the 4.0 A current draw at 24 VDC keeps the module within the output budget of small solar charge controllers and 24 V battery banks. The rotor diameter of 72 mm is matched to the BLDCDC72 brushless DC motor, an electronically commutated design with integrated drive electronics mounted inside the die-cast aluminum endcap. That endcap doubles as a heat spreader, keeping the power stage within thermal limits across the 16-28 VDC input window and at ambient temperatures up to 40 C. Speed control is via a 0-10 VDC or PWM input (factory-configurable), with tachometer output available for fault detection and DCIM integration; the fan can be operated at any point between minimum and 4250 RPM, allowing airflow to be trimmed to actual demand rather than throttled mechanically. Electrical connection is made through a 500 mm, 20AWG cable, with the lead exit oriented to suit plenum or cabinet mounting; connector type and cable length can be customized for OEM programs. The motor is Class F insulated and protected against locked rotor, over-current and under-voltage, and the fan is designed for continuous duty with an L10 bearing life of 70,000 hours at 40 C, equivalent to roughly eight years of uninterrupted operation. The die-cast aluminum housing provides a rigid mounting flange and corrosion resistance in humid or mildly alkaline environments, while the plastic impeller is unaffected by the condensate and cleaning agents commonly found in air-handling equipment. Typical applications include fan-filter units and cleanroom recirculation, laboratory fume hoods and biological safety cabinets, telecom and data-cabinet cooling, battery energy storage and EV charger enclosures, and solar-powered ventilation in off-grid installations. The FK3G175-24LH-7F is CE and RoHS compliant and is produced under FANOVA's ISO 9001 quality management system, with each unit balanced dynamically and hipot tested before shipment; OEM/ODM options include alternative control protocols, IP-rated cable glands and custom labeling.
| DC Plug Fan | ![]() |
|
| Type | FK3G175-24LH-7F | |
| Model | BLDCDC72 | |
| Nominal Voltage | VDC | 24 |
| Voltage range | VDC | 16~28 |
| Current draw | A | 4.0±10% |
| Speed(RPM) | min-1 | 4250±5% |
| Power consumption | W | 96±10% |
| Sound Pressure Level | dB(A) | 73±5% |
| Max. Air Flow | CFM / m3 /H | 939.4/798.1 |
| Max. Static Pressure | In.wg /Pa | 2.93/731 |
| Insulation class | ~ | Class B |
| Degree of protection | ~ | IP44 |
| Control Input | ~ | 0~10VDC / PWM |
| Signal Output | ~ | FG (Tach output ) |

Remarks:
Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized
Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel


Test condition:
Ⅰ.The test data is obtained under the specified environment conditions and installation mode
Ⅱ.Input Voltage---Operating voltage
Ⅲ.Temperature---Room temperature 25℃
Ⅴ.Humidity---65%RH
Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off
Ⅱ.Do not plug or unplug the fan lead plug when the fan is running
Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury
Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out
Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds
Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product
Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer
Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading
1. High Efficiency: The FK3G175-24LH-7F delivers 798.1 m3/h at 731 Pa while drawing only 96W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.
2. Industrial-Grade Impeller: The 175mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.
3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).
4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.
5. Easy Installation and Maintenance: Compact 175mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.
Q1:What kind of payments do you support?
A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping
Q2.Will you provide samples?
A2: Sample is available and can be delivered within 10days
Q3:How can I choose a more suitable model?
A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.
Q4:How can I place the order?
A4: Usually quote you within 24 hours after we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.
Q5:About transportation
A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive.
Q6:How long is the warranty period?
A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.