FG3G350-2APL-61B
| Nominal Voltage | VAC | 230 |
| Current draw | A | 2.6±10% |
| Speed(RPM) | min-1 | 2500±5% |
| Power consumption | W | 600±10% |
| Max. Air Flow | CFM / m3 /H | 2770.7/4708 |
| Max. Static Pressure | In.wg /Pa | 1.76/440 |
50pcs
When a single axial fan must move nearly 4,800 m3/h while still fitting a 350 mm frame, the FG3G350-2APL-61B is the answer. As the highest-airflow member of the FG3G350 family, this 230VAC EC axial fan delivers a maximum 4,708 m3/h (2,770.7 CFM) at 2,500 RPM, replacing two or three smaller AC fans in one compact unit. Its 600 W BLDCEC102 permanent-magnet motor runs from a wide 184-270 VAC range at 2.6 A, so it can be dropped into existing 230 V single-phase installations without a transformer or external drive. Speed is controlled by a 0-10 VDC/PWM interface or via the onboard potentiometer, giving precise airflow matching in VAV and demand-controlled ventilation systems. The motor is fully electronically commutated with integrated over-current, over-voltage and locked-rotor protection, Class F insulation and an IP54-rated die-cast aluminum housing. Dual ball bearings rated for 70,000 hours at 40 C keep maintenance intervals long, while the glass-fiber reinforced polypropylene impeller keeps rotating mass low and noise to 70.5 dB(A). Typical installations include data center CRAC units, rooftop air handlers, industrial exhaust hoods and OEM replacement of AC axial fans. The fan carries CE and RoHS compliance and is produced under ISO 9001 in FANOVA's Suzhou plant.
The FG3G350-2APL-61B is built around a 350 mm diameter impeller molded from glass-fiber reinforced polypropylene, a material chosen for its high strength-to-weight ratio, resistance to most industrial chemicals and low moisture absorption. The seven-blade aerofoil section is computer-optimized to reduce tip vortex losses, which is why the fan achieves 4,708 m3/h at 2,500 RPM without the turbulent noise signature typical of lower-blade-count designs. Each impeller is dynamically balanced to ISO 1940 G6.3 after molding, and the hub is keyed to the motor shaft with a stainless steel retaining ring to prevent slip under repeated start-stop cycles. The impeller is enclosed in a die-cast aluminum venturi housing that also acts as the motor heat sink, keeping the electronics cool even when the fan is mounted in a hot air stream. The BLDCEC102 motor is a 102 mm rotor diameter, three-phase electronically commutated machine with rare-earth magnets and an integrated inverter board. It is rated 600 W at 2,500 RPM from a 230 VAC nominal supply (operating range 184-270 VAC, 50/60 Hz) and draws 2.6 A at full load. Speed control is available through a 0-10 VDC analog input, a 25 kHz PWM input, or the onboard trim potentiometer; a tachometer output provides two pulses per revolution for system monitoring. The control board includes soft-start, over-current, over-voltage, under-voltage and locked-rotor protection, and automatically restarts after a fault clears. Insulation is Class F (155 C) with a Class B temperature rise, and the motor is protected against moisture and dust to IP54. The shaft runs in two pre-lubricated ball bearings rated for 70,000 hours L10 life at 40 C ambient, mounted in a cast-aluminum bearing housing that damps vibration and maintains alignment. Electrical connection is made through a 162 mm flying lead of 18 AWG cable, color-coded for L, N, PE, 0-10 V, PWM and tachometer, with a pre-stripped end for field termination. The fan is designed for panel or duct mounting in any orientation and weighs approximately 3.2 kg. It meets CE and RoHS directives and is manufactured in an ISO 9001-certified facility with 100% end-of-line run testing, hipot testing and dynamic balance verification. Typical applications include data center precision air conditioning, industrial ventilation, OEM air-handling units and direct replacement of AC axial fans in 230 V systems.
| AC Axial Fan | ![]() |
|
| Type | FG3G350-2APL-61B | |
| Model | BLDCEC102 | |
| Nominal Voltage | VAC | 230 |
| Voltage range | VAC | 184~270 |
| Current draw | A | 2.6±10% |
| Speed(RPM) | min-1 | 2500±5% |
| Power consumption | W | 600±10% |
| Sound Pressure Level | dB(A) | 70.5±5% |
| Max. Air Flow | CFM / m3 /H | 2770.7/4708 |
| Max. Static Pressure | In.wg /Pa | 1.76/440 |
| Insulation class | ~ | Class B |
| Degree of protection | ~ | IP44 |
| Control Input | ~ | 0~10VDC / PWM |
| Signal Output | ~ | FG (Tach output ) |

Remarks:
Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized
Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel


Test condition:
Ⅰ.The test data is obtained under the specified environment conditions and installation mode
Ⅱ.Input Voltage---Operating voltage
Ⅲ.Temperature---Room temperature 25℃
Ⅴ.Humidity---65%RH
Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off
Ⅱ.Do not plug or unplug the fan lead plug when the fan is running
Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury
Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out
Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds
Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product
Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer
Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading
1. High Efficiency: The FG3G350-2APL-61B delivers 4708 m3/h at 440 Pa while drawing only 600W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.
2. Industrial-Grade Impeller: The 350mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.
3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).
4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.
5. Easy Installation and Maintenance: Compact 350mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.
Q1:What kind of payments do you support?
A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping
Q2.Will you provide samples?
A2: Sample is available and can be delivered within 10days
Q3:How can I choose a more suitable model?
A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.
Q4:How can I place the order?
A4: Usually quote you within 24 hours after we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.
Q5:About transportation
A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive.
Q6:How long is the warranty period?
A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.