Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

FF3G200-2AGD-201 EC Forward Curved Centrifugal Fan 200mm 230V 2050 m3/h

FF3G200-2AGD-201

Nominal Voltage VAC 230
Current draw A 2.4±10%
Speed(RPM) min-1  2400±5%
Power consumption W 500±10%
Max. Air Flow CFM / m3 /H 1206.4/2050
Max. Static Pressure In.wg /Pa 4.44/1110

50pcs

Brand:
FANOVA
Spu:
FF3G200-2AGD-201
  • Overview
  • Recommended Products
Brief Description

One 200 mm forward-curved centrifugal blower can now replace two or three smaller AC fans in a single air handler. The FF3G200-2AGD-201 delivers a maximum airflow of 2050 m3/h (1206.4 CFM) and a maximum static pressure of 1110 Pa (4.44 in.wg), so duct runs can be longer, filters can be denser, and the fan array can be simpler. This is a 230VAC EC fan with a wide operating range of 184 to 270 VAC, 2.4 A current draw and 500 W input power at 2400 RPM. The heart of the unit is a BLDCEC102 electronically commutated motor with integrated control electronics, accepting 0-10V DC or PWM speed signals and providing tach output for system monitoring. The impeller is a 200 mm forward-curved wheel fabricated from cold-rolled steel plate for mechanical strength and stable blade geometry at high speed, while the die-cast aluminum endcap and housing resist vibration and corrosion. Motor protection includes locked-rotor, over-current and over-temperature safeguards, with Class B insulation as standard. Bearings are long-life sealed ball bearings rated for 40,000 hours at 40 degrees C, minimizing maintenance in continuous-duty HVAC equipment. Typical applications include air handling units, cleanroom pressurization, heat recovery ventilation, industrial exhaust and dense HEPA filtration systems. The fan carries CE and RoHS compliance, and the 18AWG 175 mm cable provides a ready-to-wire electrical interface.

Product Specification

The FF3G200-2AGD-201 is built around a 200 mm diameter forward-curved centrifugal impeller formed from cold-rolled steel plate. The wheel uses a multi-blade forward-curved geometry that produces high pressure coefficients at relatively low tip speeds, which is why this single 200 mm blower can reach 1110 Pa static pressure while moving up to 2050 m3/h. Each blade is profiled and riveted or welded to the backplate and front ring to maintain balance and dimensional stability under continuous operation. The impeller is dynamically balanced to reduce vibration and bearing load, and the steel construction tolerates higher temperatures and harsher duty than plastic alternatives. The inlet is fitted with a precision venturi for smooth airflow entry, and the complete rotating assembly is mounted inside a die-cast aluminum housing and endcap that provide rigidity, heat dissipation for the motor electronics and corrosion resistance in humid air streams.

The motor is a BLDCEC102 electronically commutated permanent-magnet rotor with a 102 mm rotor diameter. Unlike a conventional AC induction motor, the EC motor uses integrated power electronics to convert the 230VAC supply into the correct three-phase waveform, so the fan can be speed-controlled without an external VFD. The input voltage range is 184 to 270 VAC at 50/60 Hz, making the fan suitable for markets with nominal 220 to 240 V supplies and tolerant of brownouts and overvoltage. At 2400 RPM the fan draws 2.4 A and consumes 500 W, producing the stated aerodynamic performance. Speed control is via a 0-10V DC analog input or a PWM signal, and a tachometer output is provided for RPM feedback to a BMS or controller. The electronics include soft-start, locked-rotor protection, over-current limiting and over-temperature shutdown, and the motor insulation is Class B rated.

Mechanically, the shaft runs in sealed, pre-lubricated ball bearings rated for approximately 40,000 hours at 40 degrees C ambient, which supports continuous duty in air handling units without scheduled greasing. The die-cast aluminum endcap houses the bearing seats and the stator, and the housing includes mounting flanges for horizontal or vertical installation. Electrical connection is made through an 18AWG cable, 175 mm long, with flying leads for line, neutral, ground, control and tach signals. The fan is CE marked and RoHS compliant, and production units are 100 percent run-tested for airflow, power, current and noise before shipment. With a sound pressure level of 76.4 dB(A) at maximum speed, the unit is suited to plant rooms and ducted systems where the fan is acoustically isolated from occupied spaces.

Nominal Date
AC Forward Curved Centrifugal Fan image.png
Type FF3G200-2AGD-201
Model BLDCEC102

 

Nominal Voltage VAC 230
Voltage range VAC 184~270
Current draw A 2.4±10%
Speed(RPM) min-1  2400±5%
Power consumption W 500±10%
Sound Pressure Level dB(A) 76.4±5%
Max. Air Flow CFM / m3 /H 1206.4/2050
Max. Static Pressure In.wg /Pa 4.44/1110
Insulation class ~ Class B
Degree of protection ~ IP44
Control Input ~ 0~10VDC / PWM
Signal Output ~ FG (Tach output )
Connection diagram
image.png

Remarks:

Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized

Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel

Product drawing
image.png
Aerodynamic Performance Charts
image.png

Test condition:

Ⅰ.The test data is obtained under the specified environment conditions and installation mode

Ⅱ.Input Voltage---Operating voltage

Ⅲ.Temperature---Room temperature 25℃

Ⅴ.Humidity---65%RH

Safety Requirements

Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off

Ⅱ.Do not plug or unplug the fan lead plug when the fan is running

Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury

Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out

Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds

Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product

Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer

Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading

Advantages:

1. High Efficiency: The FF3G200-2AGD-201 delivers 2050 m3/h at 1110 Pa while drawing only 500W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.

2. Industrial-Grade Impeller: The 200mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.

3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).

4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.

5. Easy Installation and Maintenance: Compact 200mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.

FAQ

Q1:What kind of payments do you support?

A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping

Q2.Will you provide samples?

A2: Sample is available and can be delivered within 10days

Q3:How can I choose a more suitable model?

A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.

Q4:How can I place the order?

A4:  Usually quote you within 24 hours  after  we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.

Q5:About transportation

A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive. 

Q6:How long is the warranty period?

A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000