FB3G310-48AL-90
| Nominal Voltage | VDC | 48 |
| Current draw | A | 2.5±10% |
| Speed(RPM) | min-1 | 1720±5% |
| Power consumption | W | 120±10% |
| Max. Air Flow | CFM / m3 /H | 1132.1/1923.7 |
| Max. Static Pressure | In.wg /Pa | 1.6/400 |
50pcs
The FB3G310-48AL-90 is built for telecom and data-center engineers who work in the native -48VDC domain: it accepts a 48VDC nominal supply across a 36 to 57VDC window and moves 1923.7 m3/h (1132.1 CFM) at free air, letting a single 310 mm unit replace the paired smaller fans that typically crowd a 19-inch rack shelf or outdoor cabinet. Behind that airflow sits a backward curved impeller of die-cast aluminum with a 310 mm diameter, paired to the BLDCDC92 brushless DC motor rated 120 W at 1720 RPM; the combination develops up to 400 Pa (1.6 In.wg) of static pressure, enough to push air through dense heat-exchanger fins, washable filters and long duct runs without stalling. Speed is set by a 0-10VDC analog signal or PWM input, so a cabinet controller or DCIM layer can trim the fan between idle and full 1720 RPM in step with measured inlet temperature, cutting acoustic output well below the 67 dB(A) full-speed figure during normal load. Electrical endurance comes from dual ball bearings rated for 70,000 hours at 40 C, and the motor carries locked-rotor, reverse-polarity and over-temperature protection plus Class B insulation with a dielectric strength of 500VAC for one minute. The die-cast aluminum housing and impeller resist galvanic and humidity attack in coastal or rooftop telecom shelters, and the 20AWG, 120 mm lead set lands directly on -48VDC distribution terminals. Typical deployments include telecom outdoor cabinets, RRU thermal management, DCIM-monitored server racks, battery energy storage racks, EV charger enclosures and industrial inverter panels. The unit is CE and RoHS compliant and is produced under FANOVA's ISO 9001 quality system in Suzhou, China.
At the heart of the FB3G310-48AL-90 is a 310 mm backward curved centrifugal impeller die-cast in aluminum alloy as a single homogeneous part; the blade array is formed with a swept-back profile that converts the motor's rotational energy into pressure rather than turbulence, which is why the fan holds a stable pressure curve out to 400 Pa instead of collapsing early like a forward-curved drum. The same aluminum alloy is used for the impeller endcap and the outer housing, so thermal expansion across the assembly stays uniform from a cold start at minus 40 C to a 60 C ambient ceiling. The rotor diameter is 92 mm. The BLDCDC92 brushless DC motor is a three-phase electronically commutated design with integrated Hall sensing and a surface-mounted commutation board, eliminating brush wear and the carbon dust that contaminates cleanroom and electronics enclosures. Speed is proportional to the 0-10VDC control voltage and can alternatively be driven by a 25 kHz PWM duty signal; a tachometer output returns two pulses per revolution so a host controller can verify actual RPM against command. The fan draws 2.5 A at 48VDC nominal (120 W input) and tolerates a 36 to 57VDC supply band, covering both conventional 48V rectifier plants and the wider swing of battery-backed -48VDC telecom buses. Protection features include locked-rotor shutdown with automatic restart, reverse-polarity blocking and an internal thermal cutout that trips before winding insulation is stressed. Insulation is Class B, hipot tested at 500VAC for 60 seconds, with a minimum insulation resistance of 10 megohms at 500VDC. Mechanical support comes from two pre-lubricated dual ball bearings rated 70,000 hours L10 at 40 C, mounted in a die-cast hub that keeps rotor runout low and prevents the blade-tip rub that shortens sleeve-bearing fan life. The fan is supplied with a 120 mm, 20AWG four-conductor lead set (supply positive, supply negative, control, tach) stripped and tinned for direct termination. Acoustic output is 67 dB(A) at 1720 RPM measured at one meter on the inlet axis; below full command the backward curved blade geometry and the rigid aluminum impeller keep tonal content low, so the fan can run continuously beside occupied telecom shelters. The assembly is CE marked, RoHS compliant and manufactured under ISO 9001 with 100 percent end-of-line run-in, speed sweep and hipot testing before packing.
| DC Backward Curved Centrifugal Fan | ![]() |
|
| Type | FB3G310-48AL-90 | |
| Model | BLDCDC92 | |
| Nominal Voltage | VDC | 48 |
| Voltage range | VDC | 136~57 |
| Current draw | A | 2.5±10% |
| Speed(RPM) | min-1 | 1720±5% |
| Power consumption | W | 120±10% |
| Sound Pressure Level | dB(A) | 67±5% |
| Max. Air Flow | CFM / m3 /H | 1132.1/1923.7 |
| Max. Static Pressure | In.wg /Pa | 1.6/400 |
| Insulation class | ~ | Class B |
| Degree of protection | ~ | IP44 |
| Control Input | ~ | 0~10VDC / PWM |
| Signal Output | ~ | FG (Tach output ) |

Remarks:
Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized
Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel


Test condition:
Ⅰ.The test data is obtained under the specified environment conditions and installation mode
Ⅱ.Input Voltage---Operating voltage
Ⅲ.Temperature---Room temperature 25℃
Ⅴ.Humidity---65%RH
Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off
Ⅱ.Do not plug or unplug the fan lead plug when the fan is running
Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury
Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out
Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds
Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product
Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer
Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading
1. High Efficiency: The FB3G310-48AL-90 delivers 1923.7 m3/h at 400 Pa while drawing only 120W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.
2. Industrial-Grade Impeller: The 310mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.
3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).
4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.
5. Easy Installation and Maintenance: Compact 310mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.
Q1:What kind of payments do you support?
A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping
Q2.Will you provide samples?
A2: Sample is available and can be delivered within 10days
Q3:How can I choose a more suitable model?
A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.
Q4:How can I place the order?
A4: Usually quote you within 24 hours after we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.
Q5:About transportation
A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive.
Q6:How long is the warranty period?
A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.