FB3G175-2ALH-7F
| Nominal Voltage | VAC | 230 |
| Current draw | A | 0.45±10% |
| Speed(RPM) | min-1 | 3200±5% |
| Power consumption | W | 51±10% |
| Max. Air Flow | CFM / m3 /H | 368.2/625.6 |
| Max. Static Pressure | In.wg /Pa | 1.75/438 |
50pcs
The FB3G175-2ALH-7F is a 230VAC EC backward curved centrifugal fan that combines a lightweight glass-fiber reinforced polypropylene impeller with a brushless DC (BLDCEC72) motor to deliver 368.2 CFM (625.6 m3/h) at a maximum static pressure of 1.75 In.wg (438 Pa). Its standout superpowers are extreme energy efficiency and wide-voltage plug-and-play operation: drawing only 51 W at 3200 RPM and 0.45 A, it replaces conventional AC fans while accepting any supply from 184 to 277 VAC without a transformer. The 175 mm impeller is injection-molded from propylene with reinforced glass-fiber, giving a low-inertia, corrosion-resistant rotor that spins up quickly and resists chemical attack in HVAC and industrial air streams. The die-cast aluminum endcap and housing provide a rigid, thermally stable platform that holds bearing alignment and dampens vibration. Speed is controlled via a 0-10 VDC / PWM input or onboard potentiometer, with tach output and alarm options for system integration. Motor protection includes locked-rotor and over-temperature protection, Class B insulation, and a 20AWG 500 mm lead for simple wiring. Dual ball bearings rated for 70,000 hours at 40 degrees C ensure long service life. Typical applications include air handling units, cleanroom FFUs, kitchen and laboratory exhaust, telecom cabinet cooling, and new-energy equipment ventilation. The fan carries CE and RoHS certification and is manufactured under ISO 9001 quality management.
The FB3G175-2ALH-7F is built around a 175 mm diameter backward curved centrifugal impeller molded from glass-fiber reinforced polypropylene. The impeller features 11 backward-curved blades that are aerodynamically profiled to reduce separation losses and lower noise at the 3200 RPM design point. The hub and blade root are reinforced with a fiber-loaded polymer, allowing a thin, lightweight blade section that keeps rotor inertia low while maintaining stiffness under centrifugal load. The die-cast aluminum endcap and housing are machined in a single fixture to ensure concentricity between the bearing seats and the motor stator, which minimizes vibration and extends bearing life. The BLDCEC72 motor is an electronically commutated brushless DC motor with a 72 mm rotor diameter, using permanent magnets and a three-phase stator driven by an integrated inverter. The inverter accepts a universal 184-277 VAC input, rectifies it internally and provides power-factor-corrected DC to the motor, so the fan can be used on 230 VAC nominal systems without an external transformer. Speed control is via a 0-10 VDC analog input, a 25 kHz PWM input, or an onboard potentiometer; a tachometer output and a fault alarm relay are available for monitoring. Electrical ratings are 230 VAC nominal (184-277 VAC range), 0.45 A, 51 W, and 3200 RPM. The motor is protected against locked rotor, over-current and over-temperature, and is insulated to Class B. The fan is supplied with a 20AWG, 500 mm cable for power and control connections. The rotor runs on two pre-lubricated ball bearings rated for 70,000 hours at 40 degrees C ambient. Acoustic noise is 69.4 dB(A) at maximum speed. The fan is CE and RoHS compliant and is produced in an ISO 9001 certified facility with 100 percent end-of-line run testing.
| AC Backward Curved Centrifugal Fan | ![]() |
|
| Type | FB3G175-2ALH-7F | |
| Model | BLDCEC72 | |
| Nominal Voltage | VAC | 230 |
| Voltage range | VAC | 184~277 |
| Current draw | A | 0.45±10% |
| Speed(RPM) | min-1 | 3200±5% |
| Power consumption | W | 51±10% |
| Sound Pressure Level | dB(A) | 69.4±5% |
| Max. Air Flow | CFM / m3 /H | 368.2/625.6 |
| Max. Static Pressure | In.wg /Pa | 1.75/438 |
| Insulation class | ~ | Class B |
| Degree of protection | ~ | IP44 |
| Control Input | ~ | 0~10VDC / PWM |
| Signal Output | ~ | FG (Tach output ) |

Remarks:
Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized
Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel


Test condition:
Ⅰ.The test data is obtained under the specified environment conditions and installation mode
Ⅱ.Input Voltage---Operating voltage
Ⅲ.Temperature---Room temperature 25℃
Ⅴ.Humidity---65%RH
Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off
Ⅱ.Do not plug or unplug the fan lead plug when the fan is running
Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury
Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out
Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds
Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product
Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer
Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading
1. High Efficiency: The FB3G175-2ALH-7F delivers 625.6 m3/h at 438 Pa while drawing only 51W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.
2. Industrial-Grade Impeller: The 175mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.
3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).
4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.
5. Easy Installation and Maintenance: Compact 175mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.
Q1:What kind of payments do you support?
A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping
Q2.Will you provide samples?
A2: Sample is available and can be delivered within 10days
Q3:How can I choose a more suitable model?
A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.
Q4:How can I place the order?
A4: Usually quote you within 24 hours after we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.
Q5:About transportation
A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive.
Q6:How long is the warranty period?
A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.