Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

FB3G190-2APY-71 EC Backward Curved Centrifugal Fan 190mm 230V 909 m3/h

FB3G190-2APY-71

Nominal Voltage VAC 230
Current draw A 0.85±10%
Speed(RPM) min-1  3550±5%
Power consumption W 110±10%
Max. Air Flow CFM / m3 /H 534.83/908.8
Max. Static Pressure In.wg /Pa 2.25/563

50pcs

Brand:
FANOVA
Spu:
FB3G190-2APY-71
  • Overview
  • Recommended Products
Brief Description

Think of the FB3G190-2APY-71 not as a fan you wire in, but as an AC-powered EC blower you simply plug in and start running. That is the first of its two superpowers: a wide-range 230VAC input spanning 184 to 277 volts, so the unit rides out the voltage sag and surge of a real distribution board without a transformer, a voltage selector or a bucket of extra wiring. The second is the molded glass-fiber reinforced polypropylene impeller, a lightweight wheel that resists moisture, most dilute chemicals and long-term fatigue far better than untreated plastic, and which is matched to a die-cast aluminum housing for a stiff, low-vibration rotating assembly. The model number FB3G190-2APY-71 decodes cleanly: a 190 mm diameter backward-curved wheel, a 72 mm rotor BLDCEC72 electronically commutated motor, and a nominal 230VAC supply. At 3550 RPM the fan moves up to 534.83 CFM (908.8 m3/h) and develops a maximum static pressure of 2.25 in.wg (563 Pa) while drawing 0.85 A and 110 W, which puts it in the efficiency sweet spot where it can replace a small fixed-speed AC blower without a load increase. Speed is set by a 0-10V analog signal, a PWM input or an onboard potentiometer, so the same unit can follow a duct-pressure sensor, a thermostat or a simple hand dial. Electrical protection and insulation are built to the EC standard for a reinforced double-insulation layout, and the ball-bearing set is rated for a long continuous L10 service life suitable for 24/7 air handling. Acoustic output peaks at 70.5 dB(A), which suits plant rooms, air curtains, rooftop units and equipment cabinets rather than bedside use. Typical duties are 230VAC air-handling and CRAC units, commercial ventilation retrofits, condenser and evaporator fan decks, and light industrial exhaust; CE and RoHS compliance are standard for this platform. In short, the 2APY-71 is the drop-in AC-powered EC upgrade for anyone tired of transformer-fed DC fans.

Product Specification

The impeller of the FB3G190-2APY-71 is a 190 mm backward-curved centrifugal wheel molded in glass-fiber reinforced polypropylene, with a blade set optimized for a rising pressure curve and a stable, non-overloading operating range. The reinforced compound raises stiffness and creep resistance versus unfilled plastic while keeping rotating mass low, so the wheel accelerates quickly, spins up smoothly under EC commutation and limits bearing load at 3550 RPM. The wheel is dynamically balanced and mounted to a die-cast aluminum endcap and housing; aluminum was chosen over stamped steel for its dimensional stability, corrosion tolerance and heat spreading around the motor, giving the assembly a rigid structure that holds tight running clearances and suppresses the low-frequency vibration that shortens fan life. Inside sits the BLDCEC72 motor, a 72 mm rotor brushless DC machine with integrated electronics and permanent-magnet rotor. The built-in inverter synthesizes the three-phase drive from the rectified AC mains, so the motor delivers high efficiency and low slip losses across the whole 3550 RPM band rather than only at a fixed synchronous point. The control interface accepts a 0-10V analog demand, a PWM duty signal and a local trim potentiometer, with tach output for condition monitoring; soft-start ramps limit inrush, and the electronics include over-current, over-temperature and locked-rotor shutdown. Electrical ratings are 230VAC nominal over a 184 to 277 volt operating window, 0.85 A, 110 W, 50/60 Hz, with power factor correction typical of this EC platform. The flying lead is 20AWG cable, 500 mm long, terminating in a connector for the supply, control and tach lines. The rotor runs in a preloaded ball-bearing pair selected for continuous duty and a long L10 rating at the specified temperature; the die-cast housing locates the bearings concentrically and shields them from dust ingress. The motor is built to a reinforced insulation scheme with Class B/F thermal margins, and the finished unit is inspected for dielectric strength, insulation resistance, balance and performance before packing. Compliance covers CE and RoHS; the fan is rated for an ambient range typical of air-handling equipment, and its 70.5 dB(A) sound level suits plant-room and equipment-cabinet installation. Applications include 230VAC AHU and CRAC fan sections, ventilation retrofits where a transformer-fed DC fan is being removed, condenser and evaporator decks, and light industrial exhaust, with FANOVA OEM/ODM support for harness length, control mapping and labeling.

Nominal Date
AC Backward Curved Centrifugal Fan image.png
Type FB3G190-2APY-71
Model BLDCEC72

 

Nominal Voltage VAC 230
Voltage range VAC 184~277
Current draw A 0.85±10%
Speed(RPM) min-1  3550±5%
Power consumption W 110±10%
Sound Pressure Level dB(A) 70.5±5%
Max. Air Flow CFM / m3 /H 534.83/908.8
Max. Static Pressure In.wg /Pa 2.25/563
Insulation class ~ Class B
Degree of protection ~ IP44
Control Input ~ 0~10VDC / PWM
Signal Output ~ FG (Tach output )
Connection diagram
image.png

Remarks:

Ⅰ. Standard cable length Refer to the figure below. The length of cable can be customized

Ⅱ. Conventional mode is 0-10V/PWM control, can optionally replace the communication protocol, detailed communication protocol, please contact technical personnel

Product drawing
image.png
Aerodynamic Performance Charts
image.png

Test condition:

Ⅰ.The test data is obtained under the specified environment conditions and installation mode

Ⅱ.Input Voltage---Operating voltage

Ⅲ.Temperature---Room temperature 25℃

Ⅴ.Humidity---65%RH

Safety Requirements

Ⅰ.When taking out the fan, do not directly lift the fan lead wire. If the lead wire is excessively stressed, the internal welding part may fall off

Ⅱ.Do not plug or unplug the fan lead plug when the fan is running

Ⅲ.If the fan does not work after starting, do not touch the impeller, rotor, or other parts, professional technical personnel are required to inspect the fan to prevent sudden start of the fan from causing hand or other personal injury

Ⅳ.The power line and control line of the fan cannot be connected in reverse, otherwise it will burn out

Ⅴ.Because of the soft start characteristics of the fan, to prevent personal injury, do not touch the impeller or other parts of the fan during powered on or running at low speeds

Ⅵ.The fan needs to be operated and used under the guidance of professional personnel to prevent children from coming into touch this product

Ⅶ.If the power line is worn or damaged, it needs to be returned to the manufacturer for repair or be replaced under the guidance of the manufacturer

Ⅷ.As a part of the fan, it is not recommended to use the motor alone when there is no impeller or loading

Advantages:

1. High Efficiency: The FB3G190-2APY-71 delivers 908.8 m3/h at 563 Pa while drawing only 110W, achieving 30-40% energy savings over equivalent AC fans through FANOVA's BLDC motor technology.

2. Industrial-Grade Impeller: The 190mm galvanized steel sheet impeller resists corrosion, wear and high temperatures, making the fan suitable for harsh industrial environments and corrosive gas streams.

3. Wide Application Range: Suitable for industrial ventilation, dust extraction, HVAC units, agricultural ventilation and new-energy equipment, offering flexible customized solutions (OEM/ODM).

4. Sustainable Development: Low-voltage DC operation enables direct solar and battery integration; recyclable steel impeller and optimized BLDC drive meet eco-friendly requirements with long-term reliability.

5. Easy Installation and Maintenance: Compact 190mm footprint, 0-10VDC/PWM speed control, FG tach output and standard cable make the fan simple to wire, control and service.

FAQ

Q1:What kind of payments do you support?

A1: For sample order, 100% payment in advance; For batch order, 30% in advance and 70% will be paid before shipping

Q2.Will you provide samples?

A2: Sample is available and can be delivered within 10days

Q3:How can I choose a more suitable model?

A3: We need the information like fan type, quantity, size, material, voltage, air flow and static pressure.

Q4:How can I place the order?

A4:  Usually quote you within 24 hours  after  we get your inquiry. First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.

Q5:About transportation

A5: All available shipping ways could be applied, express shipping, air or sea. Appointed shipping company or our own forwarders all could be used in shipment. Full-way tracking the cargos for you before the goods arrive. 

Q6:How long is the warranty period?

A6: We currently offer 3-year quality guarantee for our own products, and in response to current product problems, our company provides line support, and some customers have been able to improve their products.

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000